3-BURNER LP GAS GRILL Model #DGC310CNP/DGC310CNP-D #DGC310RNP/DGC310RNP-D #DGC310BNP/DGC310BNP-D #DGC310GNP/DGC310GNP-D Français XX Français p. p. 28 XX Español Españolp.p.55 ATTACH YOUR RECEIPT HERE Serial Number _____________________________ Purchase Date ______________________ Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-877-447-4768, 8:30 a.m. – 4:30 p.m., CST, Monday – Friday or e-mail us at customerservice@ghpgroupinc.com.
TABLE OF CONTENTS Safety Information ...................................................................................................................... 3 Package Contents ...................................................................................................................... 5 Hardware Contents .................................................................................................................... 6 Preparation ...................................................................
SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble, operate or install the product. If you have any questions regarding the product, please call customer service at: 1-877-447-4768, 8:30 a.m. – 4:30 p.m., CST, Monday – Friday. DANGER • Do not use in an explosive atmosphere. Keep grill area clear and free from combustible materials, gasoline and other flammable vapors and liquids. CAUTION • Never use charcoal or lighter fluid with the grill.
SAFETY INFORMATION WARNING • Do not place the grill under overhead combustible construction or awnings. Minimum clearance from sides and back of unit to combustible construction, 36 inches (914.4mm) from sides and back. NOTE: The installation must conform with local codes or, in the absence of local codes, with either the National Fuel Gas Code, ANSI Z223.1/NFPA 54, Natural Gas and Propane Installation Code, CSA B149.1, or Propane Storage and Handling Code, B149.2.
PACKAGE CONTENTS B A C D F E G J K F H I L R M N O P X Q S V T W U PART A B C D E F G H I J K L DESCRIPTION PART QUANTITY Warming Rack Hood and Grill Body Assembly Cooking Grate Heat Tent LP Gas Tank Heat Shield Side Table Assembly Grease Cup Cart Rear Upper Brace Assembly Cart Rear Lower Brace Assembly Left Rear Leg Assembly Cart Left Upper Brace Assembly Left Front Leg Assembly M N O P Q R S T U V W X 1 1 1 3 1 2 1 1 1 1 1 1 5 DESCRIPTION QUANTITY Cart Left Lower Brace Asse
HARDWARE CONTENTS AA M6x12 Bolt Qty. 30 BB CC Wheel Wheel axle axle Wheel axle Wheel axle Cotter Cotterpin pin Cotter pin Qty. 2 Qty. 2 FF GG HH M6 Wingnut M6x18 Bolt M5 Wingnut Qty. 1 Qty. 2 Qty. 1 Cotter pin DD EE M4x12 Bolt M6x26 Bolt Qty. 6 Qty. 1 PREPARATION Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list on previous page and hardware contents above.
OPERATION INSTRUCTIONS CHECKING FOR LEAKS After all connections are made, check all connections and fittings on the LP gas tank valve, gas hose and regulator for leaks with a water and soap solution. To prevent fire or explosion while testing for a leak: • Always perform leak test prior to lighting the grill. • Do not smoke while testing for a leak. • Always perform leak tests outdoors in a well-ventilated area. • Do not use any source of flame while testing for leaks.
OPERATION INSTRUCTIONS CONNECTING GAS CYLINDER The propane gas supply cylinder to be used must be constructed and marked in accordance with the Specifications for LP Gas Cylinders of the U.S. Department of Transportation (D.O.T.) or the National Standard of Canada, CAN/CSA-B339, Cylinders, Spheres and Tubes for Transportation of Dangerous Goods; and Commission, as applicable; and provided with a listed overfilling prevention device. Use only 20-pound cylinders (height: 18.11 inches, tank diameter: 9.
OPERATION INSTRUCTIONS NOTE: Other cylinders may be acceptable for use with this appliance provided they are compatible with the appliance nesting hole and retention means. Refer to Step 15 of the Assembly Instructions for correct cylinder to cylinder holder connection. WARNING ALL INSTRUCTIONS AND SAFEGUARDS ON THIS PAGE MUST BE FOLLOWED TO PREVENT FIRE, DAMAGE AND/OR INJURY. CONNECTING THE LP TANK 1. The knob on the LP tank must be closed. Make sure that the knob is turned clockwise to a full stop.
OPERATION INSTRUCTIONS Lighting The Grill Before first use: Remove all hangings or plastic straps, if present. Before you cook on your new gas grill, it is important to clean your grill with heat. To do this, operate the grill for approximately 15 minutes with the lid closed and the control knob in the highest position. This will clean the internal parts by burning off any residue and odor from the manufacturing process.
OPERATION INSTRUCTIONS CAUTION Make sure all burners controls are off except for the burner being lit and the burners that have been lit. WARNING If ignition does not occur in 5 seconds, turn the burner control(s) OFF O . Wait 5 minutes, and repeat the lighting procedure. SHUTDOWN INSTRUCTIONS 1. Turn control knobs clockwise to the O OFF position. 2. Close valve at tank fully by turning clockwise. 3. Close lid. Turn off LP supply at cylinder when appliance is not in use.
CARE AND MAINTENANCE Cooking Grates The best time to ‘burn-off’ the cooking grates is after every use (approx. 15 minutes). The grill is already hot from cooking thus requiring less fuel to obtain necessary temperature for ‘burn-off’. To ‘burn off’ or heat clean your grill, turn the burners to highest position and run for 15 minutes with the lid closed. Then turn off the burners and use a wire brush to clean excess food residue from the grates.
CARE AND MAINTENANCE Burner Assembly Warming Rack Removing The Burner Assembly Cooking Grates 1. Make sure all control knobs are in the OFF position, gas supply valve is closed, and the gas hose is disconnected from the gas supply. Heat Tents 2. Open lid and remove warming rack, cooking grates, heat tents, clip for burner, ignition chain and main burner. 3. Remove hinge pin as illustrated in Figure 1. Figure 1 4. Slide main burmers out of firebox. 5. Detach ignition wire from electrode in Figure 2.
CARE AND MAINTENANCE Cleaning the Burner Assembly – Make sure the grill is cool 1.Turn gas off at the control knobs and LP gas cylinder. 2. Disconnect LP gas cylinder from regulator and hose. 3.Remove warming rack, cooking grates and heat tents. 4.Detach burner by removing the cotter pins at the back of the burners to detach them from the brackets. 5.Detach ignition wire from electrode by hand only. DO NOT use pliers or any other tool as it may damage the electrode or wire. 6.Lift burner slowly. 7.
TROUBLESHOOTING If you have any questions regarding the product, please call customer service at 1-877-447-4768, 8:30 a.m. – 4:30 p.m., CST, Monday – Friday. PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION The burner will not light using the ignitor procedure (weak or no spark being generated). 1. The igniter electrode may be covered with grease or residue. 2. The igniter electrode may have a loose or disconnected wire. 3. Cracked or broken ignition electrode. 1. Clean the ignitor electrode. Low Heat. 1.
TROUBLESHOOTING PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION The burner will not light with a match. 1. Match not reaching burners (when holding match with hand). 2. Empty tank. 1. Use match holder found in cabinet door. 3. Poor connection between valve regulator and LP cylinder coupling. 4. Burner inlet blocked. No gas flow or an 1. Tank valve not on or fully obstructed gas flow. opened. 2. Empty tank. 3. Poor connection between valve regulator and LP cylinder coupling. 4. Burner inlet blocked.
REPLACEMENT PARTS LIST 2 1 3 4 6 5 7 9 11 10 12 8 13 14 15 16 18 17 21 19 23 20 22 24 25 26 23 27 29 28 33 35 30 31 32 38 34 36 39 37 41 42 26 40
REPLACEMENT PARTS LIST For replacement parts, call our customer service department at 1-877-447-4768, 8:30 a.m. – 4:30 p.m., CST, Monday – Friday.
