3-Burner LP Gas Grill with SearPLUS™ BURNER Model #DGH353CRP/DGH353CRP-D Français Françaisp.p.29 Español Españolp.p.57 Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-877-447-4768, 8:00 a.m. – 4:30 p.m., CST, Monday – Friday or e-mail us at CustomerService@ghpgroupinc.
Table Of Contents Safety Information................................................................................................................................ 3 Package Contents................................................................................................................................ 5 Hardware Contents.............................................................................................................................. 6 Preparation.........................................
Safety Information Please read and understand this entire manual before attempting to assemble, operate or install the product. If you have any questions regarding the product, please call customer service at: 1-877-4474768, 8:00 a.m. – 4:30 p.m., CST, Monday – Friday. DANGER • Do not use in an explosive atmosphere. Keep grill area clear and free from combustible materials, gasoline and other flammable vapors and liquids.
Safety Information WARNING • Do not place the grill under overhead combustible construction or awnings. Minimum clearance from sides and back of unit to combustible construction, 36 inches (914.4mm) from sides and back. 36in 36in 914.4mm 36in 914.4mm 914.4mm NOTE: The installation must conform with local codes or, in the absence of local codes, with either the National Fuel Gas Code, ANSI Z223.1/NFPA 54, Natural Gas and Propane Installation Code, CSA B149.1, or Propane Storage and Handling Code, B149.
Package Contents A B H C I D M A1 B1 J C1 K F E S O L K G N U Z R T Y P Q W V X PART A B C D E F G H I J K L M N O DESCRIPTION Lid Handle Assembly Temperature Gauge Temperature Gauge Bezel Grill Body Assembly Control Knob Grease Cup Holder Grease Cup Warming Rack Cooking Grate Heat Tent For Main Burner Side Table Control Knob For Sear Burner Heat Tent For Sear Burner Tank Heat Shield Left Leg Assembly QTY.
Hardware Contents AA BB CC DD 2X 2X 2X 20X St4 8x10 Screw M8 Nut M8 Wrench M6x16 Screw EE FF GG HH II 2X 2X 2X 4X 16X M6 Wing Nut M6 Spring Washer M6 Plain Washer M4x10 Screw M5x14 Screw Preparation Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list on previous page and hardware contents above. If any part is missing or damaged, do not attempt to assemble the product. Contact customer service for replacement parts.
Operation Instructions CHECKING FOR LEAKS After all connections are made, check all connections and fittings on the LP gas tank valve, gas hose and regulator for leaks with a water and soap solution. To prevent fire or explosion while testing for a leak: • • • • • • Always perform leak test prior to lighting the grill. Do not smoke while testing for a leak. Always perform leak tests outdoors in a well-ventilated area. Do not use any source of flame while testing for leaks.
Operation Instructions CONNECTING GAS CYLINDER The propane gas supply cylinder to be used must be constructed and marked in accordance with the Specifications for LP Gas Cylinders of the U.S. Department of Transportation (D.O.T.) or the National Standard of Canada, CAN/CSA-B339, Cylinders, Spheres and Tubes for Transportation of Dangerous Goods; and Commission, as applicable; and provided with a listed overfilling prevention device. Use only 20-pound cylinders (height: 18 inches, tank diameter: 12.
Operation Instructions NOTE: Other cylinders may be acceptable for use with this appliance provided they are compatible with the appliance nesting hole and retention means. Refer to Step 16 of the Assembly Instructions for correct cylinder to cylinder holder connection. WARNING ALL INSTRUCTIONS AND SAFEGUARDS ON THIS PAGE MUST BE FOLLOWED TO PREVENT FIRE, DAMAGE AND/OR INJURY. CONNECTING THE LP TANK 1. The knob on the LP tank must be closed. Make sure that the knob is turned full stop.
Operation Instructions Lighting The Grill Before first use: Remove all hangings or plastic straps, if present. Before you cook on your new gas grill, it is important to clean your grill with heat. To do this, operate the grill for approximately 15 minutes with the lid closed and the control knobs in the highest position. This will clean the internal parts by burning off any residue and odor from the manufacturing process.
Operation Instructions LIGHTING THE GRILL WITH A MATCH 1. 2. 3. 4. Open the lid. Insert a match in the end of the match holder that is installed on the inside of the cabinet door. Light the match. Immediately place the lit match through the spaces in the grill grates near the ports of the burner between the heat tents as shown. Make sure the lit match is close to the burner ports. 5.
Care and Maintenance Cooking Grates The best time to “burn-off” the cooking grates is after every use (approx. 15 minutes). The grill is already hot from cooking, thus requiring less fuel to reach the necessary temperature for “burn-off.” To “burn off” or heat-clean your grill, turn the burners to highest position and run for 15 minutes with the lid closed. Then turn off the burners and use a wire brush to clean excess food residue from the grates.
Care and Maintenance Burner Assembly Removing The Burner Assembly 1. Make sure all control knobs are in the OFF position, gas supply valve is closed, and the gas hose is disconnected from the gas supply. 2. Open lid and remove warming rack, cooking grates, heat tents, and smoker box assembly. 3. Remove hinge pin as shown in Figure 1. 4. Slide main burners and SearPLUS™ burner out of firebox. 5. Detach ignition wire from electrode in Figure 2.
Care and Maintenance WARNING If these instructions are not followed, a fire or explosion may result, possibly causing serious bodily injury or death. Cleaning the Burner Assembly – Make sure the grill is cool. 1. Ensure all burner ports are clear of clogs. Use of a pin or paper clip works well. 2. Ensure burner is free of any damage. If damage is found, replace with new burner. 3. Ensure the end of the burner and primary air screen are clear from insect nests, dirt or debris.
