User manual
Table Of Contents
- 1 Introduction
- 2 Controls, Indicators and Connections
- 2.1 Input Mono
- 2.2 Input Stereo
- 2.3 FX 1/2
- 2.4 AUX 1/2
- 2.5 MON 1/2
- 2.6 MASTER with GEQ
- 49 - MASTER LED DISPLAY
- 50 - MUTE
- 51 - PFL
- 52 - MASTER L/R fader
- 53 - STANDBY
- 54 - MASTER A OUT L/R
- 55 - MASTER A INSERTS L/R
- 56 - MASTER B OUTPUTS L/R
- 57 - MASTER B
- 58 - PRE/POST of MASTER B
- 59 - STEREO/MONO of MASTER B
- 60 - PHONES jack
- 61 - PHONES control
- 62 - REC SEND L/R
- 63 - 2TRACK IN L/R
- 64 - 2TRACK to MASTER
- 65 - REC SEND & USB OUT
- 66 - LAMP 12V/5W
- 67 - 11-BAND STEREO GRAPHIC EQUALIZER
- 68 - GRAPHIC EQ to MASTER / MON 1/2
- 2.7 DISPLAY with function keys
- 2.8 Rear panel
- 3 Display & functions
- 4 DIGITAL AUDIO INTERFACE
- 5 Setting up a standard PA
- 6 Setup examples
- 1 Einführung
- 2 Bedienelemente und Anschlüsse
- 2.1 Input Mono
- 2.2 Input Stereo
- 2.3 FX 1/2
- 2.4 AUX 1/2
- 2.5 MON 1/2
- 2.6 MASTER mit GEQ
- 49 - MASTER LED-Display
- 50 - MUTE-Schalter
- 51 - PFL-Schalter
- 52 - MASTER L/R-Fader
- 53 - STANDBY-Schalter
- 54 - MASTER A OUT L/R-Buchsen
- 55 - MASTER A INSERTS L/R-Buchsen
- 56 - MASTER B OUTPUTS L/R-Buchsen
- 57 - MASTER B-Regler
- 58 - PRE/POST-Schalter für MASTER B
- 59 - STEREO/MONO-Schalter für MASTER B
- 60 - PHONES-Buchse
- 61 - PHONES-Regler
- 62 - REC SEND L/R-Buchsen
- 63 - 2TRACK IN L/R-Buchsen
- 64 - 2TRACK to MASTER
- 65 - REC SEND & USB OUT-Regler
- 66 - LAMP 12V/5W
- 67 - 11-BAND STEREO GRAPHIC EQUALIZER
- 68 - GRAPHIC EQ to MASTER / MON 1/2
- 2.7 DISPLAY mit Funktions-Tasten
- 2.8 Rückseite
- 73 - Netzbuchse
- Die Spannungsversorgung des CMS erfolgt ausschließlich mit dem mitgelieferten IEC-Netzkabel über eine verriegelnde Netzbuchse. Schließen Sie das CMS nur an eine geeignete Netzversorgung an, die den auf dem Typenschild angegebenen Anforderungen ent...
- 74 - Netzschalter (POWER)
- 75 - MIDI IN/OUT-Buchsen
- 3 Display & Funktionen
- 4 DIGITAL AUDIO INTERFACE
- 5 Aufbau einer Standard-PA
- 6 Aufbaubeispiele
- 7 Specifications
CMS
3
24
63 - 2TRACK IN L/R
Here you can connect a recorder, a CD/MP3 player, an
open reel or an additional SUB-mixer. The signal is
post master fader and post STANDBY switch, which
allows playing intermission music during performance
breaks or checking the mix during the rehearsal, using
the headphones. You just have to engage the STAND-
BY switch to mute all channel signals at the master
outputs. The 2TRACK IN signal however will pass un-
obstructed.
HINT: The 2TRACK IN signal is not available at the
REC SEND connectors, the DIGITAL AUDIO
INTERFACE or the MASTER B OUTPUTS in
PRE fader mode.
64 - 2TRACK
TO MASTER
This control is used to mix the 2TRACK signal to the
master mix, post fader of the master controls.
CAUTION: When adjusting the level of the device
that is connected to the 2TRACK IN –
CD player, tape deck, etc. – always
begin with the 2TRACK to MASTER con-
trol set at its minimum setting. Other-
wise, depending on the output quality
of the connected sound source, the out-
putted level can instantly “hit the top”.
65 - REC SEND & USB OUT
This control allows adjusting the volume at the REC
SEND outputs or, when used, the level of the DIGITAL
AUDIO INTERFACE output channels.
66 - LAMP 12V/5W
This XLR-type socket provides a DC voltage of 12V/
5 watts and is meant for the connection of a goose-
neck lamp. Please make sure that the used lamp com-
plies with the here mentioned specifications and pin
assignment. We recommend using the gooseneck
lamp (DC-LITLITE-4P), available from the DYNACORD
accessory assortment. For further information, please
consult your local dealer.
67 - 11-BAND STEREO GRAPHIC EQUALIZER
The master channel employs a 11-band stereo equal-
izer, which gets activated through the use of the ON
button. The EQ’s insert point is post master fader and
pre power amplifier. The EQ is bypassed when the EQ
ON switch is not locked in its “ON” position. Eleven
frequency bands offering 10 dB boost/cut and a qual-
ity of Q = 2 allow shaping the overall sound to meet
your personal preferences or to optimally match it to
the acoustic conditions of different locations.
Illustration 2-18: Pin assignment of LAMP 12V/5W output