Installation manual

ManualsBrandsDynalite ManualsConsumer electronicsDMC810GL

WMGD Pty Limited trading as Dynalite ABN 33 097 246 92

Unit 6, 691 Gardeners Road Mascot NSW 2020 Australia

t +61 8338 9899 f +61 2 8338 9333 dynalite.info@philips.com philips.com/dynalite

DMC810GL

Leading Edge Dimmer/HF Ballast Controller

Installation Manual

contents

Warning…………………………………………….. 2

Dimmable Lamps Chart……………………….….. 7

Features…………………………………………….. 2

Troubleshooting……………………………………. 8

Important Safeguards…………………………….. 2

Specification………………………………………. 8

Internal View……………………………………….. 3

Mounting…………………………………….……… 4

Supply & Load Cable Connections.……………… 5

Connecting Serial Control Cables……………….. 6

Hardware Controls …………………………………7

Summary of content (8 pages)

PAGE 1
DMC810GL Leading Edge Dimmer/HF Ballast Controller Installation Manual contents Warning…………………………………………….. 2 Features…………………………………………….. 2 Important Safeguards…………………………….. 2 Internal View……………………………………….. 3 Mounting…………………………………….……… 4 Supply & Load Cable Connections.……………… 5 Connecting Serial Control Cables……………….. 6 Hardware Controls …………………………………7 Dimmable Lamps Chart……………………….….. 7 Troubleshooting……………………………………. 8 Specification……………………………………….
PAGE 2
important safeguards Warning     TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS DEVICE TO RAIN OR MOISTURE. DO NOT ENERGISE UNLESS THE FRONT COVER IS IN PLACE. THIS DEVICE MUST BE EARTHED. INSTALLATION, PROGRAMMING AND MAINTENANCE MUST BE CARRIED OUT BY QUALIFIED PERSONNEL features        Single Phase Supply Simple supply requirement, single phase at 40A. 4 Dimmed Outputs Each dimmed 10A output is independently regulated, protecting loads from voltage surges and spikes.
PAGE 3
internal view Entry Gland Plate for Load Cables Circuit Breakers and Emergency Lighting line Outputs Dimmed or Switched 230V Outputs 40A Single Phase Supply Connections 4 x Side Entry Gland Knockouts DALI Broadcast, 1-10V or DSI Control Outputs Earth Link Accessory Port DyNet Port Network Socket Service Switch Service LED Low Voltage Cable Gland For spare parts, please call your nearest Dynalite Customer Service Centre, and specify: DMC810GL 3 DMC810GL Installation Manual Rev E.
PAGE 4
mounting Select a Suitable Location This device is designed for indoor use only. If installing in an external location, the DMC810GL must be housed in a suitable well-ventilated enclosure. Choose a dry location that will be accessible after the installation is complete. To ensure the cooling system functions correctly, the DMC810GL should only be mounted vertically, the right way up.
PAGE 5
supply & load cable connections Supply Cables 1. Supply Terminals 2. Emergency Lighting Terminals 3. Load Terminals 4. Ballast Control Terminals 1-10V, DSI, or DALI Broadcast 3. 2. 1 . The Phase & Neutral supply terminals are located toward the middle of the enclosure. The supply cables shall have a minimum capacity of 40A, to prevent cable overheating.
PAGE 6
connecting serial control cables Connecting Data Cable Connect Data Cable in a ‘Daisy Chain’ Determine Your Requirements Serial ports are used to interconnect other dimmers, smart control panels, sensors and AV controllers. Serial port devices can be identified by 6 terminals, labelled: SHLD, GND, DATA+, DATA-, +VE, AUX.
PAGE 7
preset programming using the program key AUX Input - This is a dry contact interface that is active low. The dry contact is connected between the AUX and GND terminals on the DyNet connector strip. The function of the AUX input is programmable. Ensure that the cable length between the dry contact and terminal strip is no longer than 2 metres.
PAGE 8
Trouble shooting Check the following list. If you are still unable to rectify the situation, contact your nearest Dynalite office. A complete list of distributors worldwide can be found on the Internet at: www.philips.com/dynalite Please ensure that you have completed the following prior to calling our technical support department.