Instructions for Use

Turbo-14 DECAL
FuselageTurbo-01
Turbo-02 wing Turbo-03 Vertical stabilizer
Turbo-07 Plastic Part set
Turbo-08
Landing gear
Turbo-9 Canopy
Turbo-10 Hardware
Turbo-11 Duct
Turbo-12 6 leaf blades
Turbo-13 Duct hardware
DY-1007 9g Servo
DY-6006 11.1V 2200mAh 20C Li-Po Battery
DY-3003 Glue
DYE-1004 40A ESC
DYR-2001
2.4G Receiver
Turbo-04 Elevator
Turbo-05 EDF SET
Turbo-06 Cockpit
DECAL:
DY8937
Dynam RC
dynam-rc.cn
of
This product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Please recycle.
over
DIRECTIONS FOR ASSEMBLY AND ADJUSTMENT
SPARE PART LIST:
Wingspan: 1180mm
Fuselage Length: 1080mm
Flying weight: 1150g
Servo: 9gX4
Battery: 11.1v 2200mAh 20C Li-Po
ESC: 40AX2
Motor: KV3300X2
Wing loading: 63g/dm
2
ASSEMBLY:
Insert the speed controllers
into fuselage.
Apply the foam glue on the joiner of
the left and right horizontal stabilizer.
Insert the vertical stabilizer into
the fuselage.
Secure the EDF set on the
fuselage with 3X40mm screw.
Glue the horizontal
stabilizer in place.
Secure the vertical stabilizer on the
fuselage with 2.3X20mm screw.
Insert the direction pushrod into the
hold of quick-controller and tighten
clamp connectors.
Insert speed controller
wires into THR channel of receiver.
Fix the nose landing gear
on fuselage with 2.5X8mm screw.
Insert Z-bend of pushrod into the hole
of the nose landing gear.
Apply the foam glue to the stuffing
foam and insert it into fuselage
as shown.
Insert elevator pushrod into the hold
of quick-controller and tighten
clam connectors.
(Remark: The servo should be in center position)
18
Apply the foam glue on the joiner of the
left and right wings.
Apply the foam glue on the plastic part
and insert it in the main wing
as shown.
Apply the foam glue on the joiner of
the rear landing gear and push
it in the position.
Secure the wing on fuselage
with 6X50mm plastic screw.
Put the battery in position.
Connect the aileron servos
with Y wires.
Glue the left and right main wings
together.
Apply the foam glue to the stuffing
foam and insert it into wing as
shown.
19
20
55-60mm
Center of gravity
55-60mm
Center of gravity
55
60
ESC-40A
Leads with silicon
rubber(red/black)
11.1V 2200mAh
Li-Po 20C
ESC-40A
ESC-40A
EDF 64
5
4
5
6
7
3
17
265
17
21
12
11
2
1
6
8
16
13
13
20
10
24
1
19
23
24
25
26
27
28
29
30
31
32
33
18
22
3
8
9
10
How to open
canopy
DY-1024- Turbojet front E-Retract
DYT-1023 E-Retract ø3.1 90
BM2815D-KV3600 Brushless Motor
DYAT-008 Servo Horn
DY-3001 quick-controller
DY-3007 Flap hinges
Turbo-15 Plastic Tab
Turbo-16 Screw set