Owner's Manual

I
:1
i
l'A'hll
t Component Specifications
Damp
with~
Appearance:
Black butyl
core
with
4
mil aluminum
constraining
layer, self adhesive
with
release liner
Mass:
0.4Sibs./ft.
2
(2.20kg/m
2
)
Adhesive
Peel Strength:
42.6
lb./in.
(74.8 N/cm)
Diffuse with Back-Wave Foam
Appearance:
Dark gray
polyurethane
foam
Mass:
0.16
lbs.
(72 g)
Tensil
Strength:
20psi(138
kPa)
Dimensions:
13" x 9"
(33cm
x 22cm)
Thickness:
0.067"(1.7mm)
Temperature
Range
(Optimal Performance):
14
°F
to
+ 140
°F
(
-1
0 °(
to
+60
°()
Temperature
Range
(Resistance):
-
65
°F
to
+300
°F
(-54 o
cto+
149
°()
Thickness:
1"
(25.4mm)
Density:
2 lbs./ft
3
(32kg/m
3
)
Tear
Resistance:
1.1
pli
(193N/M)
Adhesive:
Peel
and stick
self-adhesive
Decouple with
~~~~~
Dynil
barrier between
two
layers
of
gray acoustic foam.
FOAM
Thickness:
1.5" (38.1 mm)
total
Mass:
0.16
lb/ft
2
(0.78 kg/m
2
)
Density:
2.0
lb/ft
3
(0.125
kg/m
3
)
Tensile
Strength:
15
psi
Tear
Strength:
1.9
Thermal Conductivity
(R):
1.9 (hr-ft
2
-deg.F /BTU)
Standards:
Meets UL94
HF-1
Temperature
Range
(Resistance):
-40
°F
to
+225
°F
(-40
°(
to+
107
°()
Installation
DYNIL™
Appearance:
Black Flexivinyl
Barrier
Color:
Charcoal
Gray
STC:
28
Mass:
lib
per
square
foot
Thickness:
0.09
inches
Temperature
Range
(Resistance):
-40 °F
to
+220
°F
(-40
°(
to+
1
OS
0
()
Standards:
Meets
UL94-VO
Chemical
Resistance:
Resistant
to
water and
mineral oils
En-Wall
kits are designed for easy retrofit
or
new
construction
Before you start, make sure you have chosen
the
proper
size
of
the
En
-
Wall
Kit based on your wall
thickness
(4"
or
6").
For retrofit installation,
first remove
the
in-wall
speaker.
Prepare
the
surface
by
wiping
the
dust,
dirt
and debris from
the
area
behind the
in
-wall
speaker opening.
Place
Dyna
mat
Xtreme on a
flat
surface, a
nd
attach
the
B
ac
k-Wave
Fo
am
to
the
aluminum
face.
Fold
the Dynamat Xtreme/Back-Wave Foam
as
needed
to
pass
through
the
in-wall
speaker opening.
Remove
the
release liner
and attach
the
Dynamat
Xtreme/Back-Wave Foam
ass
e
mbly
to
the
clean drywall
making sure
that
it
adheres properly.
(Be
careful
not
to
drop
the Dynamat Xtreme/Back-
Wave
Foam in the
wall.)
Slide
the
SoundSnake
through
the
hole
and position one
end against a wall
stud.
Insert
remainder
of
SoundSnake
to
create a rounded corner
enclosure
(See
picture on opposite
side).
Position
th
e speaker
wir
e behind
th
e
SoundSnake
against
th
e back
wall.
Finish
by
joining
th
e e
nd
s
of
th
e
SoundSnake
together.
Install
(re-install)
the
in-wall
speaker.