Passport™ P4 AC Plus 4 Port AC/DC Multi-Charger Instruction Manual
NOTICE All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit horizonhobby.com and click on the support tab for this product.
• Always end the charging process if the battery becomes hot to the touch or starts to change form (swell) during the charge process. • Always connect the charge cable to the charger first, then connect the battery to avoid short circuit between the charge leads. Reverse the sequence when disconnecting. • Always connect the positive red leads (+) and negative black leads (–) correctly. • Always disconnect the battery after charging, and let the charger cool between charges.
Specifications AC Power Distribution Channels A and C: 100 watts total Channels B and D: 100 watts total Power Distribution Channels A and B: 50 – 100 watts Adjustable Range Channels C and D: 0 – 50 watts Charge Current Channels A and B: 0.1 – 10 Amps Channels C and D: 0.1 – 5 Amps Charge Voltage LiPo: 4.18 – 4.25V/cell LiHV: 4.25 – 4.35V/cell LiFe: 3.58 – 3.7V/cell LiIon: 4.08 – 4.2V/cell NiMH/NiCd: Uses delta peak detection Discharge Wattage 10 Watts per channel Discharge Current 0.
C A D B E Not to scale. Not all wiring shown. Not all connectors shown. L F M N O G H P I Q J R S T U V W K LEFT SIDE (PORT A) X Y Z The right side of the charger features the same connections for port B as the left side has for port A.
BLUETOOTH CONNECTION Scan the QR code at the right to download the Dynamite Dashboard App. All Charger features are accessible from the app. QR Code to download app Compatible with iOS and Android devices 1. Download the Dynamite Dashboard App from the iOS or Play Store. 2. Install the app and verify the Bluetooth is activated on the mobile device. 3. Power on the charger, and open the app. The app will open a dialog box that says Bluetooth Device, touch the line that says charger to connect.
FLOW CHART BATT/PROGRAM Li** BATT Li** 2.0A Li** 2.0A Li** 2.0A Li** 2.0A Li** 1.0A BALANCE CHG 14.8V (4S) CHARGE 14.8V (4S) FAST CHG 14.8V (4S) STORAGE 14.8V (4S) DISCHARGE 14.8V (4S) BATT/PROGRAM Ni** BATT Ni** CHARGE CURRENT 2.0A Ni** Auto CHARGE CURRENT 3.0A Ni** DISCHARGE 1.0A CUT: 3.2V Ni** RE-PEAK 1 Ni** CYCLE CHG>DCHG 1 BATT/PROGRAM Pb BATT Pb CHARGE 2.0A 12.0V (6P) Pb DISCHARGE 1.0A 12.0V (6P) BATT/PROGRAM BATT METER 0.00 0.00 0.00 V 0.00 V MAIN: 0.00V H:0.00 L:0.
GETTING STARTED CAUTION: Before charging, always ensure you have chosen the correct battery chemistry type for the battery you are charging. CAUTION: Never connect the AC and DC input cords to an active power source at the same time. This will void the warranty, cause product damage and possibly injure the user. WHEN USING AN EXTERNAL DC POWER SOURCE: 1. Connect the DC power cord to the charger DC Power Input Port. 2. Connect the DC power source. 3.
OPERATING YOUR CHARGER POWER UP SCREEN When the charger is powered ON, there is a series of self tests and the charger will require the user to verify they have read the manual by pressing the ENTER / Start button. The charger will not proceed with charge functions until this process is completed. NEVER LEAVE THE CHARGER UNATTENDTED WHILE IN OPERATION. NEVER CHARGE ON OR AROUND COMBUSTIBLE MATERIALS. Charging batteries can be dangerous if proper precautions are not taken.
LI** (LI-PO/LI-FE/LI-ION) LITHIUM DISCHARGING 1. Connect the banana plugs of the battery adapter cable to the charge port. Confirm the positive and negative connectors match, red to red (positive to positive) and black to black (negative to negative). 2. Connect the Balance Port to the Balance Circuit Adapter Board. 3. Connect the battery connector to the battery adapter cable. 4. Connect the balance connector of the battery to the Balance Adapter Board. 5.
NI** (NI-MH/NI-CD) CHARGING CAUTION: Before charging or discharging, always ensure you have chosen the correct battery chemistry type for the battery you are charging. 1. Connect the banana plugs of the battery adapter cable to the charge port. Confirm the positive and negative connectors match, red to red (positive to positive) and black to black (negative to negative). 2. Connect the battery connector to the battery adapter cable. 3. Press the Batt / PROG Stop button to access the root menu.
NI** (NI-MH/NI-CD) CYCLE CHARGING 1. Connect the banana plugs of the battery adapter cable to the charge port. Confirm the positive and negative connectors match, red to red (positive to positive) and black to black (negative to negative). 2. Connect the battery connector to the battery adapter cable. 3. Press the Batt / PROG Stop button to access the root menu. Press the DEC or INC button to scroll through the main menu screens until you reach Program Select=Ni-MH/Ni-Cd. 4. Press the ENTER / Start button.
CAUTION: Before charging, always ensure you have chosen the correct battery chemistry type for the battery you are charging. PB CHARGING 1. Connect the banana plugs of the battery adapter cable to the charge port. Confirm the positive and negative connectors match, red to red (positive to positive) and black to black (negative to negative). 2. Connect the battery connector to the battery adapter cable. 3. Press the Batt / PROG Stop button to access the root menu.
BATTERY MEMORY The charger can store up to 10 settings for specific batteries. The following images show programming a Li** battery, options will vary with Ni** and Pb battery types. [ BATT MEMORY X ] ENTER SET-> BATT TYPE LiPo 1. Press the Batt / PROG Stop button to access the root menu. Press the DEC or INC button to scroll through the main menu screens until you reach BATT/PROGRAM BATT MEMORY. 2. Press the ENTER / Start button to enter the Battery Memory settings 3.
SCAN TO GO The Passport P4 can be automatically set with the SCAN TO GO feature by scanning a compatible QR code. Check your battery for a compatible QR code. If you need to add one, a QR code can be generated from within the Battery Memory section. HOW TO GENERATE A QR CODE: 1. Add battery memory settings to match your battery. 2. Touch the QR code next to the battery memory, save it to the Gallery on your device. 3. Print the QR code and apply it to your battery.
SYSTEM SETTINGS 1. Press the Batt / PROG Stop button to access the root menu. Press the DEC or INC button to scroll through the main menu screens until you reach BATT/PROGRAM SYSTEM SETTING page. 2. Press the ENTER / Start button to enter the system setting menu. 3. Press the DEC or INC button to scroll through the menu. 4. Press the ENTER / Start button to edit the parameter. 5. Press the DEC or INC button to increase or decrease the value. 6. Press the ENTER / Start button again to save the selection. 7.
NI-CD SENSITIVITY D. PEAK – DEFAULT The D.Peak (Delta Peak) value is adjustable between 3mV/Cell and 15mV/ Cell. 10mV/Cell is a good starting point for Ni-Cd batteries. If the Delta Peak value is too high, you risk overcharging the battery; if the value is too low, charging will stop before the battery reaches full capacity. KEY BEEP (DEFAULT ON) / BUZZER (DEFAULT ON) Use the Key Beep/Buzzer menu to set the key beep and charger alarm buzzer at ON or OFF as needed.
TROUBLESHOOTING During charger operation, circuits monitor battery and charger functions. If the following messages show on the charger’s LCD screen, make the recommended responses. If the message continues after you respond as recommended, contact your nearest Horizon Hobby customer service center for assistance.
WARRANTY AND SERVICE CONTACT INFORMATION Country of Purchase Horizon Hobby Contact Information Address Horizon Service Center (Repairs and Repair Requests) United States of America servicecenter.horizonhobby. com/RequestForm/ Horizon Product Support productsupport@ horizonhobby.com. (Product Technical Assistance) 877-504-0233 Sales 2904 Research Rd Champaign, Illinois, 61822 USA websales@horizonhobby.
Inspection or Services - If this Product needs to be inspected or serviced and is compliant in the country you live and use the Product in, please use the Horizon Online Service Request submission process found on our website or call Horizon to obtain a Return Merchandise Authorization (RMA) number. Pack the Product securely using a shipping carton. Please note that original boxes may be included, but are not designed to withstand the rigors of shipping without additional protection.
FCC INFORMATION FCC ID: REY-Q200 FCC Information This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
© 2019 Horizon Hobby, LLC. Dynamite, Passport, EC3 and the Horizon Hobby Logo are trademarks or registered trademarks of Horizon Hobby, LLC. All other trademarks, service marks and logos are property of their respective owners.