User Manual

4
Included Items
AC Power Cord
(4) Charge Adapter: Banana to EC3™ Device (DYNC0072)
(2) Bare charge leads
(4) Balancing Adapter Board: XH (DYN5032)
Optional Items
Temperature Sensor (DYN5033)
Dynamite
®
LiPo Charge Bag: small (DYN1400), large (DYN1405)
Charge Adapter: Banana to Deans (DYNC0056)
Charge Adapter: Banana to XT60 (DYNC0143)
DC Power Cord: Alligator to XT60 (DYNC1108)
CONTROL LAYOUT
A. DC Power Input Port
B. DC Power Cable (optional, not included)
C. Main Power Switch
D. AC Power Input Cable
E. AC Power Input Port
F. LCD Screen
G. Charge Port Selection Button
H. Charge Port C Positive Power Output
I. Charge Port C Negative Power Output
J. Charge Port C Balance Connector
K. Balance Board
L. BATT/PROG Stop
M. DEC (decrease)
N. INC (increase)
O. ENTER/Start
P. Charge Port D Negative Power Output
Q. Charge Port D Positive Power Output
R. Charge Port D Balance Board Connector
S. Charge Port D Temperature Sensor Port
T. PC Link
U. 5V 2.1A USB Power supply
V. Charge Port C Temperature Sensor Port
W. Battery Adapter Cable
X. Charge Port A Negative Power Output
Y. Charge Port A Positive Power Output
Z. Charge Port A Temperature Sensor Port
AA. Charge Port A Balance Connector
Specifications
AC Power Distribution Channels A and C: 100 watts total
Channels B and D: 100 watts total
Power Distribution
Adjustable Range
Channels A and B: 50 – 100 watts
Channels C and D: 0 – 50 watts
Charge Current Channels A and B: 0.1 – 10 Amps
Channels C and D: 0.1 – 5 Amps
Peak Charge Voltage LiPo: 4.18 – 4.20V/cell LiHV: 4.20 – 4.35V/cell LiFe: 3.58 – 3.6V/cell LiIon: 4.08 – 4.1V/cell
NiMH/NiCd: Uses delta peak detection
Discharge Wattage 10 Watts per channel
Discharge Current 0.1 – 2 Amps per channel
Discharge Cut-off Voltages LiPo: 3.0 – 3.3V/cell LiHV: 3.1 – 3.4V/cell LiFe: 2.6 – 2.9V/cell LiIon: 2.9 – 3.2V/cell
NiMH/NiCd: 0.1 – 1.1V/cell
Input Voltage 100 – 240V AC (50 – 60Hz); 11 – 18V DC
Charging Capability 1 – 6S Li-Po/Li-HV/Li-Ion/Li-Fe; 1 – 15C Ni-Cd/Ni-MH; 2 – 12V Pb
Battery Capacities 100 – 50000 mAh
Charge Current
Channel A/B: 0.1A – 10A Channel C/D: 0.1-5A (in 0.1A Increments/100W max AC, 200W DC)
Discharge Current 0.10A – 5.0A x 4 (in 0.1A Increments/10W max)
Balance Current 200mA max per cell
Operating Temperature 0ºC to + 40ºC
Charging Mode Ni-Cd/Ni-MH: Peak; 1-6S Li-Po/Li-HV/Li-Ion/Li-Fe/Pb: CC/CV
Protection Short-circuit, over-current, reverse polarity, low input voltage, over-temperature
Standard Battery Parameters
Battery Type LiPo LiIon LiFe LiHV NiCd NiMH PB
Nominal Voltage (per cell) 3.7V 3.6V 3.3V 3.7V 1.2V 1.2V 2.0V
Max Charge Voltage (per cell) 4.2V 4.1V 3.6V 4.35V 1.5V 1.5V 2.4V
Storage Voltage (per cell) 3.8V 3.7V 3.3V 3.85V n/a n/a n/a
Allowable Fast Charge Rate ≤1C ≤1C ≤4C ≤1C ≤1C ≤1C ≤0.4C
Minimum Discharge Voltage (per cell) 3.0V 2.9V 2.6V 3.1V 0.9V 0.9V 1.8V