User Manual
9
OPERATING YOUR CHARGER
POWER UP SCREEN
When the charger is powered ON, there is a series of self tests and
the charger will require the user to verify they have read the manual by
pressing the ENTER / Start button. The charger will not proceed with
charge functions until this process is completed.
BATT/PROGRAM
Li** BATT
Li** CHARGE
2.0A 14.8V (4S)
BATT/PROGRAM
Ni** BATT
Ni** CHARGE
CURRENT 2.0A
Ni** Auto CHARGE
CURRENT 3.0A
Ni** DISCHARGE
1.0A CUT: 3.2V
Li** FAST CHG
2.0A 14.8V (4S)
Li** BALANCE CHG
2.0A 14.8V (4S)
Li** STORAGE
2.0A 14.8V (4S)
Li** DISCHARGE
1.0A 14.8V (4S)
Ni** RE-PEAK
1
Ni** CYCLE
CHG>DCHG 1
BATT/PROGRAM
SYSTEM SETTING->
Safety Timer
ON 120Min
Capacity Cut-Off
ON 5000mAh
Temp Cut-Off
On 50C 122F
Temperature Unit
Celcius
Rest Time
CHG>DCHG 10Min
NiMH Sensitivity
D.Peak 4mV
Key Beep ON
Buzzer ON
Bal. Connection
ON
Load Factory Set
Enter
Version
HW:1.00 SW:1.03
Pb CHARGE
2.0A 12.0V (6P)
Pb DISCHARGE
1.0A 12.0V (6P)
BATT/PROGRAM
Pb BATT
0.00 0.00 0.00 V
0.00 V
MAIN: 0.00V
H:0.00 L:0.00V
BATT/PROGRAM
BATT METER
BATTERY CHECK
...................
0.00 0.00 0.00
0.00 0.00 0.00
BATT/PROGRAM
BATT RESISTANCE
NiCd Sensitivity
D.Peak 4mV
BATT/PROGRAM
BATT MEMORY
DC INPUT LOW
10.0V
AC MAX POWER
100W
VERSION
HW: FW:
[ BATT MEMORY X ]
ENTER SET-> LiPo
BATT TYPE
BATT VOLTAGE
14.8V(4S)
CHARGE CURRENT
2.0A
DISCHRG CURRENT
1.0A
DISCHG VOLTAGE
3.0V/CELL
4.20V
TVC=YOUR RISK!
SAVE PROGRAM
ENTER
NEVER LEAVE THE CHARGER UNATTENDTED WHILE IN OPERATION.
NEVER CHARGE ON OR AROUND COMBUSTIBLE MATERIALS.
Charging batteries can be dangerous
if proper precautions are not taken.
By Pressing the ENTER button you
are confirming that you understand
this and that you have read the
manual and understand the warnings
enclosed.
WARNING!
DYNAMITE PASSPORT
P2 AC PLUS
2 PORT ACDC CHARGER
DYNC3016
BATT/PROGRAM
LiPo BATT
BATT/PROGRAM
LiPo BATT
BATT/PROGRAM
LiPo BATT
BATT/PROGRAM
LiPo BATT
A
B
C
D
LI** (LI-PO/LI-HV/LI-FE/LI-ION) LITHIUM CHARGING
1. Connect the banana plugs of the battery adapter cable to the charge port.
Confirm the positive and negative connectors match, red to red (positive to
positive) and black to black (negative to negative).
2. Connect the Balance Adapter Board to the Balance Port of the charge port.
3. Connect the battery connector to the battery adapter cable.
4. Connect the balance connector of the battery to the balance adapter.
5. Press the Batt / PROG Stop button to access the root menu. Press the DEC
or INC button to scroll through the main menu screens until you reach
Program Select=Li-Po/Li-Ion/Li-Fe.
6. Press ENTER / Start
7. Press the DEC or INC Button to scroll through the program options (Charge,
Balance Charge, Storage, Discharge). Select Charge.
8. Press ENTER / Start to select a program option. The Parameter will begin
flashing.
9. Press the DEC or INC Button to change the value of the parameter. Press
the ENTER / Start Button again to move to the next parameter.
10. Once the parameters are at the desired settings, press and hold the
ENTER / Start Button for 3 seconds. Press ENTER / Start again to confirm
and start the charge process.
11. The charger will check the battery and charger settings and charging will
begin.
12. Press the DEC Button to see the rest of the Charging information. Press
the INC Button to see the voltages for each cell.
13. Press ENTER / Start to return to the charging screen.
14. Press the Batt / PROG Stop Button at any time to stop charging.
15. When charging is complete, the charger will sound a series of beeps.
16. Disconnect the battery from the charger when the charge is complete.
4.20 4.20 4.20
0.00 0.00 0.00
BATT/PROGRAM
Li** BATT
Li** CHARGE
2.0A 14.8V (4S)
2.0A 14.8V (4S)
BATT/PROGRAM
Ni** BATT
Ni** CHARGE
CURRENT 2.0A
Ni** Auto CHARGE
CURRENT 3.0A
Ni** DISCHARGE
1.0A CUT: 3.2V
Li** FAST CHG
2.0A 14.8V (4S)
Li** BALANCE CHG
2.0A 14.8V (4S)
Li** STORAGE
2.0A 14.8V (4S)
Li** DISCHARGE
1.0A 14.8V (4S)
Ni** RE-PEAK
1
Ni** CYCLE
CHG>DCHG 1
BATT/PROGRAM
SYSTEM SETTING->
Safety Timer
ON 120Min
DC SUPPLY: OFF
CH1:50W CH2:50W
Capacity Cut-Off
ON 5000mAh
Temp Cut-Off
On 50C 122F
Temperature Unit
Celcius
Rest Time
CHG>DCHG 10Min
NiMH Sensitivity
D.Peak 4mV
Key Beep ON
Buzzer ON
Key Beep ON
Voice ON
Bal. Connection
ON
Load Factory Set
Enter
Version
HW:1.00 SW:1.03
Pb CHARGE
2.0A 12.0V (6P)
Pb DISCHARGE
1.0A 12.0V (6P)
BATT/PROGRAM
Pb BATT
0.00 0.00 0.00 V
0.00 V
MAIN: 0.00V
H:0.00 L:0.00V
BATT/PROGRAM
BATT METER
BATTERY CHECK
...................
0.00 0.00 0.00
0.00 0.00 0.00
BATT/PROGRAM
BATT RESISTANCE
NiCd Sensitivity
D.Peak 4mV
BATT/PROGRAM
BATT MEMORY
DC INPUT LOW
10.0V
AC MAX POWER
100W
VERSION
HW: FW:
[ BATT MEMORY X ]
ENTER SET-> LiPo
BATT TYPE
BATT VOLTAGE
14.8V(4S)
CHARGE CURRENT
2.0A
DISCHRG CURRENT
1.0A
DISCHG VOLTAGE
3.0V/CELL
4.20V
TVC=YOUR RISK!
SAVE PROGRAM
ENTER
BATT/PROGRAM
Li** BATT
Li** CHARGE
2.0A 14.8V (4S)
2.0A 14.8V (4S)
BATT/PROGRAM
Ni** BATT
Ni** CHARGE
CURRENT 2.0A
Ni** Auto CHARGE
CURRENT 3.0A
Ni** DISCHARGE
1.0A CUT: 3.2V
Li** FAST CHG
2.0A 14.8V (4S)
Li** BALANCE CHG
2.0A 14.8V (4S)
Li** STORAGE
2.0A 14.8V (4S)
Li** DISCHARGE
1.0A 14.8V (4S)
Ni** RE-PEAK
1
Ni** CYCLE
CHG>DCHG 1
BATT/PROGRAM
SYSTEM SETTING->
Safety Timer
ON 120Min
DC SUPPLY: OFF
CH1:50W CH2:50W
Capacity Cut-Off
ON 5000mAh
Temp Cut-Off
On 50C 122F
Temperature Unit
Celcius
Rest Time
CHG>DCHG 10Min
NiMH Sensitivity
D.Peak 4mV
Key Beep ON
Buzzer ON
Key Beep ON
Voice ON
Bal. Connection
ON
Load Factory Set
Enter
Version
HW:1.00 SW:1.03
Pb CHARGE
2.0A 12.0V (6P)
Pb DISCHARGE
1.0A 12.0V (6P)
BATT/PROGRAM
Pb BATT
0.00 0.00 0.00 V
0.00 V
MAIN: 0.00V
H:0.00 L:0.00V
BATT/PROGRAM
BATT METER
BATTERY CHECK
...................
0.00 0.00 0.00
0.00 0.00 0.00
BATT/PROGRAM
BATT RESISTANCE
NiCd Sensitivity
D.Peak 4mV
BATT/PROGRAM
BATT MEMORY
DC INPUT LOW
10.0V
AC MAX POWER
100W
VERSION
HW: FW:
[ BATT MEMORY X ]
ENTER SET-> LiPo
BATT TYPE
BATT VOLTAGE
14.8V(4S)
CHARGE CURRENT
2.0A
DISCHRG CURRENT
1.0A
DISCHG VOLTAGE
3.0V/CELL
4.20V
TVC=YOUR RISK!
SAVE PROGRAM
ENTER
CAUTION: Before charging or discharging, always ensure you have
chosen the correct battery chemistry type for the battery you are charging.