DYNAMIX DW-01 Plus/H User’s Manual
PREFACE............................................................................................................................V PART I: Dynamix DW-01Plus/H GATEWAY OVERVIEW .................................................. 1 1.1 Overview...................................................................................................................................2 1.2 Software Specifications ...........................................................................................................
.4.4 VoIP Incoming Call ...........................................................................................................42 PART IV: WEB MANAGEMENT INTERFACE ................................................................. 44 4.1 Login and welcome screen .....................................................................................................45 4.2 Save and Reboot.....................................................................................................................46 4.
5.3.6 [commit] .......................................................................................................................... 83 5.3.7 [ifaddr]............................................................................................................................. 84 5.3.8 [time] ............................................................................................................................... 87 5.3.9 [ping] .......................................................................
Dynamix DW-01Plus/H Gateway User Manual Part I: Dynamix DW-01Plus/H Gateway Overview This part introduces the software/hardware specifications and default settings of the Dynamix DW-01Plus/H Gateway.
Dynamix DW-01Plus/H Gateway User Manual 1.1 Overview The Dynamix DW-01Plus/H is a one-port telephone extension and three ports SOHO Router to IP network gateway. It provides Data transfer by 10/100Mbps, telephone services and T.38 fax over IP network with easily operation and configuration. It is most suitable for SOHO and small-to-medium enterprise in Internet communication environment.
Dynamix DW-01Plus/H Gateway User Manual 1.2 Software Specifications Dynamix DW-01Plus/H Gateway Features Provide Voice over IP and Fax over IP features. Built-in NAT/IP sharing function FSK and DTMF Caller ID Transmit Voice and T.38 fax simultaneously Support T.38 ECM function (Error Correction in high speed fax Mode) Provides call progress tone E.
Dynamix DW-01Plus/H Gateway User Manual Remote Firmware Upgrade You can use FTP/TFTP to perform firmware upgrade for the Dynamix DW-01Plus/H Gateway from a remote location. Security Password protection for system management Built-in NAT function. CE, FCC Certification 1.3 Hardware Specifications Chassis 190mm(W) x 110mm(D) x 51.5mm(H) Weight (unit): 0.3 kg Four 10/100 Base-T Ethernet RJ-45 ports (Auto LAN MDI/MDIX). Input AC 100V-240V, Output DC 12V.
Dynamix DW-01Plus/H Gateway User Manual Power (Green): (1) Light on: Dynamix DW-01Plus/H is connected with power adapter correctly and power on. (2) Light off: Dynamix DW-01Plus/H is not connected with power adapter correctly or not power on. Status (Green): (1) (2) (3) Light on: Dynamix DW-01Plus/H is under Gatekeeper mode and successfully register to Gatekeeper. Light off: Under Peer-to-Peer mode.
Dynamix DW-01Plus/H Gateway User Manual Ethernet Port: Ethernet port is for connecting VoIP Gateway to network, transmit rate supports 10/100 Base-T. Ethernet connector LAN/WAN TEL Port: RJ-11 connector, Dynamix DW-01Plus/H interface to connect analog phone sets or trunk port of PABX. PSTN Port (Dynamix DW-01Plus/H Only): RJ-11 connector, Dynamix DW-01Plus/H interface to CO PSTN line or extension port of PABX. DC 12V Port: DC 12V Power supply.
Dynamix DW-01Plus/H Gateway User Manual Part II: Start-UP This part explains how to configure essential and basic items before user can run Dynamix DW-01Plus/H gateway.
Dynamix DW-01Plus/H Gateway User Manual 2.1 Software Installation Guide This guide covers all essential configurations under different application, user can follow steps below to configure basic items to run Dynamix DW-01Plus/H gateway. 2.1.1 Default Settings of Dynamix DW-01Plus/H gateway WAN IP Parameters (1) (2) WAN IP Address = 10.1.1.3 Subnet mask = 255.0.0.0 Default gateway = 10.1.1.254 LAN IP Address = 192.168.123.123 Subnet mask = 255.255.255.
Dynamix DW-01Plus/H Gateway User Manual Connect the WAN port (silver) on the Dynamix DW-01Plus/H Gateway to the Ethernet port of your network (e.g. Cable Modem, ADSL Modem) using the standard CAT-5 straight Ethernet cable. Step 2. Connect your PC to the LAN port of Dynamix DW-01Plus/H Connect your PC to the LAN port of Dynamix DW-01Plus/H with standard CAT-5 straight Ethernet cable. Step 3.
Dynamix DW-01Plus/H Gateway User Manual 2.1.3 Essential Configuration via Web Management interface This section describes how to setup Dynamix DW-01Plus/H via Web management interface. Please follow procedures below to configure essential items before you use Dynamix DW-01Plus/H gateway. 2.1.3.1 Save Data and Reboot After any configuration has been made, user has to save all data and reboot system to make configurations take effect. Step 1. Click [Commit Data] on the navigation panel.
Dynamix DW-01Plus/H Gateway User Manual Step 3. Close the current browser windows and launch your web browser again.
Dynamix DW-01Plus/H Gateway User Manual 2.1.3.2 Setup Network (1) Fixed IP To configure the VoIP Gateway IP address, please click [Network Interface] on the navigation panel. In the Network Interface screen, type a new IP address, subnet mask and the default routing gateway (e.g. IP Address: 192.168.13.62, Subnet mask: 255.255.248.0, Default routing gateway: 192.168.8.254) and click the OK button.
Dynamix DW-01Plus/H Gateway User Manual (2) DHCP Click [Network Interface] on the navigation panel. In the Network Interface screen, enable the DHCP function if you are using the cable modem or DHCP server and click the [OK] button.
Dynamix DW-01Plus/H Gateway User Manual (3) PPPoE Configuring the VoIP Gateway IP address for PPPoE Mode. Click [Network Interface] on the navigation panel. In the Network Interface screen, Select IP mode: PPPoE, and put the info of the PPPoE User Name, password, and Reboot After Remote Host Disconnection: Enable (e.g. User: 123456@hinet.net, password: 123456) and click the [OK] button.
Dynamix DW-01Plus/H Gateway User Manual - PPPoE User Name: Set PPPoE authentication User Name. PPPoE Password: Set PPPoE authentication password. Reboot After Remote Host Disconnection: Enable/Disable auto reboot after PPPoE disconnection. If user enables this function, after PPPoE being disconnected, Dynamix DW01Plus/H will automatically reboot to re-connect, and after rebooting, if Dynamix DW-01Plus/H still can’t get contact with server, Dynamix DW-01Plus/H will keep trying to connect.
Dynamix DW-01Plus/H Gateway User Manual 2.1.3.3 Application mode-GK/Peer-to-Peer Mode After setting IP address, user must assign Dynamix DW-01Plus/H to work under GK routed mode or Peer-to-Peer mode. If there is no Gatekeeper, please set your Dynamix DW-01Plus/H as Peer-to-Peer Mode. 2.1.3.3.1 GK routed mode GK mode means that there will be an intermediate Gatekeeper between Dynamix DW01Plus/H Gateway and the remote entity.
Dynamix DW-01Plus/H Gateway User Manual To configure Peer-To-Peer Mode in Dynamix DW-01Plus/H Gateway, follow the steps below: Step 1. Configure the Dynamix DW-01Plus/H Gateway H323 Configuration. Click [H323 Configuration] on the navigation panel. In the H323 Configuration screen, select Peer-to-Peer Mode function, set Line1 number and click the [OK] button. Step 2. Configure Phone Book in the Dynamix DW-01Plus/H Gateway. Click [Phone Book] on the navigation panel.
Dynamix DW-01Plus/H Gateway User Manual - 18 -
Dynamix DW-01Plus/H Gateway User Manual 2.1.4 Essential Configuration via Telnet Command Line interface This section describes how to setup Dynamix DW-01Plus/H via Telnet command line interface. Please follow procedures below to configure essential items before you use Dynamix DW-01Plus/H gateway. 2.1.4.1 Save Data and Reboot After any configuration has been made, user has to save all data and reboot system to make configurations take effect. Step 1.
Dynamix DW-01Plus/H Gateway User Manual usr/config$ commit usr/config$ reboot Step 4. When Dynamix DW-01Plus/H successfully establish PPPoE connection, use command [ifaddr -print] to see detail information. For example: usr/config$ ifaddr -print IP mode : PPfPoE PPPoE adapter information Status : Ready IP address : 61.223.39.135 Destination : 61.223.128.254 DNS primary : 168.95.192.1 Subnet Mask : 255.255.255.
Dynamix DW-01Plus/H Gateway User Manual 2.1.4.3 Application mode-GK/Peer-to-Peer Mode After setting IP address, user must assign Dynamix DW-01Plus/H to work under GK routed mode or Peer-to-Peer mode. If there is no Gatekeeper, please set your Dynamix DW-01Plus/H as Peer-to-Peer Mode. 2.1.4.3.1 GK routed mode GK mode means that there will be an intermediate Gatekeeper between Dynamix DW01Plus/H Gateway and the remote entity.
Dynamix DW-01Plus/H Gateway User Manual Step 2. Configure Phone Book, using “pbook” command. usr/config$ pbook –add name TEST1 ip 10.1.1.1 e164 10 In this case user add one callee record named as TEST1, IP address as 10.1.1.1, and mapping e.164 number as 10. After phone book data has been set, user can dial 10 to make a call for IP 10.1.1.1. After the command completed, you can type “pbook –print” to see if the input record is correct.
Dynamix DW-01Plus/H Gateway User Manual 2.1.5 Essential Configuration via Installation Wizard Installation Wizard is a friendly software tool that can provide you an easy way to configure your Dynamix VoIP devices. You only need to Input the MAC address of your product and Click [Search Device]; you can configure your VoIP device without changing your PC’s setting. Additionally, when you forget IP address of the VoIP device, Installation Wizard gives you a solution to solve this problem.
Dynamix DW-01Plus/H Gateway User Manual 2.1 Special Housing Installation Guide Dynamix DW-01Plus/H has special adjustable housing for vertical or horizontal type. Please follow procedures as below to change type you like. 2.1.1 Horizontal Type 2.1.1.1 Insert stand board on one side. 2.1.1.2 Insert the other stand board on the other side. 2.1.1.3 Finally Dynamix DW-01Plus/H can stand as horizontal type.
Dynamix DW-01Plus/H Gateway User Manual 2.1.2 Vertical Type 2.1.2.1 Insert stand board on one side. 2.1.2.2 Insert the other stand board on the same side. 2.1.2.3 Finally Dynamix DW-01Plus/H can stand as vertical type.
Dynamix DW-01Plus/H Gateway User Manual Part III: Special Applications and Features This part explains how to configure Dynamix DW-01Plus/H Gateway under special application mode, such as behind NAT, and how to upgrade firmware.
Dynamix DW-01Plus/H Gateway User Manual 3.1 Behind IP-Sharing 3.1.1 IP Sharing Configuration 3.1.1.1 One Dynamix DW-01Plus/H Gateway behind IP Sharing device This application is only for the user who is using the IP Sharing device. It is said Gateway is connected behind IP Sharing. The IP Sharing Device must support the DMZ or Virtual server functions such as ADSL network. Step 1. The WAN IP Address obtained from ADSL has two kinds of methods.
Dynamix DW-01Plus/H Gateway User Manual Please see following for example: >Advanced setting > NAT setting > DMZ Host setting DMZ Host setting ▣ Activate DMZ DMZ Host IP: 192.168.1.5 Step 6. Configure the Dynamix DW-01Plus/H Gateway IP address for IP Sharing Mode. Click [Network Interface] on the navigation panel. In the Network Interface screen, enter the IP address, Subnet mask and the default gateway in the network table. Please follow up your IP Sharing device Step 7.
Dynamix DW-01Plus/H Gateway User Manual Step 9. Click [Reboot System] on the navigation panel. In the VoIP Gateway screen, click the [Reboot] button. It will take around 40 seconds to reboot. Step 10. Close the current browser windows and launch your web browser again. Enter the new IP address in the Location or Address field.
Dynamix DW-01Plus/H Gateway User Manual 3.2 NAT mode (PPPoE) Step 1. Set PPPoE mode, using [ifaddr –mode 2], input the user id & password provided by your ISP, using [ifaddr –id –pwd], reboot the device after disconnection, using [ifaddr –reboot 1] usr/config$ ifaddr –mode 2 usr/config$ ifaddr –id 123@hinet.net (PPPoE login account) usr/config$ ifaddr –pwd 123 (PPPoE login Passowd) usr/config$ ifaddr –reboot 1 (Enable) Step 2.
Dynamix DW-01Plus/H Gateway User Manual usr/config$ ifaddr -print IP mode : PPPoE PPPoE adapter information Status : Ready IP address : 61.223.39.135 Destination : 61.223.128.254 DNS primary : 168.95.192.1 Subnet Mask : 255.255.255.255 Authenticate : PAP Protocol : TCP/IP Device : PPP/PPPoE DHCP server switch : Enable NAT function switch : Enable LAN port IP (for NAT) : 192.168.123.123 DNS primary : 168.95.192.1 DNS secondary : 168.95.1.1 HTTP port : 80 SNTP : mode=1 server 168.95.195.
Dynamix DW-01Plus/H Gateway User Manual location (where xxx is a number between 2 and 254 used by the VoIP Gateway to identify each computer), and the default [Subnet Mask 255.255.255.0]. Please notice that two computers on the same LAN cannot have the same IP address. Set Default Gateway value as 192.168.123.123 in the [new gateway] field. Then save your change. PC can also use DHCP mode when DHCP server of Dynamix DW01Plus/H is enabled.
Dynamix DW-01Plus/H Gateway User Manual 3.3 Upgrade Your Dynamix DW-01Plus/H . 3.3.1 Upgrade via Web management interface 3.3.1.1 Before start Step 1. Please confirm Host PC, which is installed as TFTP / FTP server and is in available network. Step 2. Note down your current configurations, such as [H323 Configuration], [Phone Book]. 3.3.1.2 Upgrade Version Step 1. To update the Dynamix DW-01Plus/H Gateway ROM Version, please click [ROM Upgrade] on the navigation panel.
Dynamix DW-01Plus/H Gateway User Manual Step 3. Click [Flash Clean] on the navigation panel. In the Flash Clean screen, click the [CLEAN] button. Step 4. In the Flash Clean screen to Display [Flash cleaned!! Please reboot your system!!], when Flash Clean Ok.
Dynamix DW-01Plus/H Gateway User Manual Step 5. Click [Reboot System] on the navigation panel. In the Reboot Dynamix DW01Plus/H Gateway screen, click the [Reboot] button. It will take 40 seconds to reboot. Step 6. Close the current browser windows and launch your web browser again. Enter the IP address in the Location or Address field. 3.3.2 Upgrade via Telnet Command interface Use [rom] command to upgrade software of Dynamix DW-01Plus/H.
Dynamix DW-01Plus/H Gateway User Manual Parameter Usages: -print: show versions of all rom files. -app, boot, boot2m, dsptest, dspcore, dspapp, ht: To update main Application program code, Boot code, DSP testing code, DSP kernel code, or DSP application code, and Hold Tone file. Note: Most of all, the Rom file needed to get upgrade is App or Boot2m. Please check the exact Rom file before doing download procedure. -s: To specify TFTP server’s IP address when upgrading ROM files.
Dynamix DW-01Plus/H Gateway User Manual 3.4 Dynamix DW-01Plus/H PSTN Line Application 3.4.1 PSTN Outgoing Call 3.4.1.1 Make PSTN call from TEL Phone set Default TEL line is intended to make IP call, if user wants to make a call via PSTN line, please dial “* #”, then user will hear dial tone from PSTN side. The dial tone between IP side and PSTN are different. If the PSTN port doesn't connect a PSTN line, press “*#”, the signal will be back to IP side then play busy tone. 3.4.1.
Dynamix DW-01Plus/H Gateway User Manual Part IV: Web Management Interface This part explains how to configure the Dynamix DW-01Plus/H Gateway via WEB management interface.
Dynamix DW-01Plus/H Gateway User Manual 4.1 Login and welcome screen Step 1. Start your web browser. Step 2. Launch your web browser and enter [192.168.123.123] (the default IP address of the LAN port) in the Location or Address field. Press Enter. Step 3. Password request screen will appear as below. Please input “root” or “administrator” in the user name field and no password in the password field. Step 4. Click OK. Step 5. After a successful login, you will see the welcome screen described next.
Dynamix DW-01Plus/H Gateway User Manual 4.2 Save and Reboot Click OK at the end of every configuration page to confirm your changes. All configurations will not take effect before reboot system. Please remember to do [Commit Data] to save all configuration then [Reboot System] to reboot Dynamix DW01Plus/H.
Dynamix DW-01Plus/H Gateway User Manual 4.3 Web Management Configuration 4.3.1 Network Interface Click [Network Interface] in the navigation panel and open the Network Interface Screen. - IP Mode: To configure the fixed or dynamic IP address for this unit. Please configure to PPPoE if the ADSL is using the PPPoE type.
- Dynamix DW-01Plus/H Gateway User Manual IP Address: Set WAN IP Address of Dynamix DW-01Plus/H. Subnet Mask: Set the Subnet Mask of Dynamix DW-01Plus/H Default routing gateway: Set Default routing gateway of Dynamix DW-01Plus/H DHCP server: The DHCP server IP address. DHCP Server switch: Enable the DHCP function for the LAN interface. NAT function switch: To enable or disable the NAT function. LAN port IP for NAT: To configure the LAN port IP for the NAT device.
- - Dynamix DW-01Plus/H Gateway User Manual After Remote Host Disconnection: This unit will reboot and re-connect to the ISP Send PPPoE Echo Request: In the PPPoE mode, if the network connector or the ADSL modem was lost, after the connector and modem connected, it will reboot automatically for the re-connect with the PPPoE server. EMS IP: Set the EMS server IP address. EMS User name: Set the EMS login user name. EMS password: Set the EMS login password. EMS time: Set the EMS search time.
4.3.2 H323 Configuration Screen Dynamix DW-01Plus/H Gateway User Manual Click [H323 Configuration] in the navigation panel and open the H323 Configuration Screen. - Mode: Pick up the calling mode for this gateway. 1. GK routed: Users have to register on the GK if users picked up this option. 2.
- Dynamix DW-01Plus/H Gateway User Manual define the phone book for this mode. Gatekeeper IP Address: Enter the GK ip if users pick up the GK routed mode. It support on GK mode only. 2nd Gatekeeper IP: Support the secondary GK function. It support on GK mode only. Default Gateway IP: if the number couldn’t be found in the phone book configuration, it will be sent to this location. Gateway Type: Pick up the type for gateway. It support on GK mode only. 1.
- - - Dynamix DW-01Plus/H Gateway User Manual RTP Port: The UDP port for the voice sending. RTP ports support a range of the UDP. The line 1 is using UDP (RTP) 16384 and (RTCP) 16385. The line 2 is using UDP (RTP) 16386 and (RTCP) 16387….etc. This configuration is defining the start port for the RTP packets. Support the GK and Peer-to-Peer mode both. Gatekeeper finding port: The port for the Gatekeeper Discovering function of this gateway. Support the GK mode only.
4.3.3 Line Configuration Dynamix DW-01Plus/H Gateway User Manual Click [System Configuration] in the navigation panel and open the [System Configuration] Screen. The Line configuration will show the status of the registrations and the ports. It includes the hunt group, hotline, and no answer forward configuration. - - - Type: Just show the interface for this port. Hunt Group: Define the group number of this port. When the port is busy, the call could be transferred to another port in the same group.
Dynamix DW-01Plus/H Gateway User Manual 4.3.4 Phone Book Configuration Screen Click [PPPoE Configuration] in the navigation panel and open the [PPPoE Configuration] Screen. The Phone Book configuration is only support the gateway in Peer-to-Peer mode. - Add Data: User can specify 5 sets of phone book via Web Management Interface. Please input index, Name, IP Address and E.164 number of the destination device.
Dynamix DW-01Plus/H Gateway User Manual 4.3.5 Support Configuration Screen Click [Support Configuration] in the navigation panel and open the [Support Configuration] Screen. This gateway supports the FAX over IP, fast start function and other functions. - - T.38 FAX: Enable this function to support the FAX function. T.38 FAX Request Mode: The switch can control the request message sending or not. This is the special function, please info your reseller before you change this switch. T.
Dynamix DW-01Plus/H Gateway User Manual 4.3.6 System Configuration Screen Click [System Configuration] in the navigation panel and open the [System Configuration] Screen. - Inter Digit Time: The call will be sent out if user didn’t enter the digits after this timer.
- - Dynamix DW-01Plus/H Gateway User Manual Forward time: It supports the No Answer Forward function. If users configure it for 10, the call will be forwarded when it rings about 10 seconds. From 5 to 65535. Keypad Type: User could define the keypad for the DTMF sending. 1. In-Band : The DTMF signal sending by RTP. 2. - Out-Band : The DTMF signal sending not by RTP. Including the H.245(Alpha), H.245(Signal), Q.931 and RFC 2833.
- - - Dynamix DW-01Plus/H Gateway User Manual users configure this for 1. Only support FXO. Delay to add DTMF (FXO): The timer for sending DTMF signal, if the calls are from the IP to PSTN side. It could only support the one-stage-dialing function. Only support FXO. Auto connect time (FXO): The FXO will send the connect message to the IP side is this timer is up in the one-stage-dialing function. It could only support the one-stage-dialing function. Only support FXO.
4.3.7 Voice Configuration Screen Dynamix DW-01Plus/H Gateway User Manual Click [Voice configuration] in the navigation panel and open the [Support Configuration] Screen. - - - Codec Priority: Set priority preference of installed codes, G.723, G.711A, G.711U, G.729, G.729A, G.729B, and G.729AB. Frame Size: Set Specify sending packet size, G.723: 30/60/90, G.711A, G.711U, G.729, G.729A, G.729B, G.729AB: 20/40/60ms.The smaller the packet size, the shorter the delay time.
Dynamix DW-01Plus/H Gateway User Manual 4.3.8 Phone Configuration Screen Click [Phone Configuration] in the navigation panel and open the [Phone Configuration] Screen. For tone simulation, Dynamix DW-01Plus/H Gateway adopts dual frequencies as traditional telephone does. If users want to have their own call progress tone, they can change the value of tones. - Ring Cadence: Setting the played tone type, when VoIP Gateway is receiving a call.
Dynamix DW-01Plus/H Gateway User Manual Note: For tone simulation, VoIP Gateway adopts dual frequencies as traditional telephone does. If users want to have their own call progress tone, they can change the value of tones. High and Low frequency/level/cadence can be configured respectively.
Dynamix DW-01Plus/H Gateway User Manual 4.3.9 RTP Pay Load Type Configuration Click [RTP Payload Type Configuration] in the navigation panel and open the [RTP Payload Type Configuration] Screen. - RFC2833 Payload Type: To define the payload type for RFC2833 type. DTMF Payload Type: To define the payload for the DTMF type. FAX Payload Type: To define the payload for the FAX type. FAXByPass Payload type: To define the payload for the FAX by Pass type.
Dynamix DW-01Plus/H Gateway User Manual 4.3.10 IP Packets ToS Configuration Screen The Type of Service should be worked with the network router. The router will check all the packets if it support the TOS function. There is a field in the packet for the TOS value. This WEB is for users to configure these values to make the packets with the correct values for the TOS service from the gateway.
Dynamix DW-01Plus/H Gateway User Manual DROP Precedence Class #1 Class #2 Class #3 Class #4 (AF11) (AF21) (AF31) (AF41) 001010 010010 011010 100010 (AF12) (AF22) (AF32) (AF42) 001100 010100 011100 100100 (AF13) (AF23) (AF33) (AF43) 001110 010110 011110 100110 Low Drop Precedence Medium Drop Precedence High Drop Precedence Please refer to RFC standard documents for more information about what is DSCP.
4.3.11 DDNS Screen Dynamix DW-01Plus/H Gateway User Manual Dynamix DW-01Plus/H supports DDNS function. Before using this function, please have a DDNS account and some info from your DDNS server. Click [Password configuration] in the navigation panel to open the [Password Configuration] screen. - Status: To enable or disable this function. Server: Enter the server address of your DDNS server. Host Name: Your DDNS address. ID: Your account. Password: Your password.
Dynamix DW-01Plus/H Gateway User Manual 4.3.12 Prefix Configuration Screen The Prefix function is using the drop and inserts function. Click [Prefix Configuration] in the navigation panel and open the [Prefix Configuration] Screen. - - Index: Setting the index number for prefix record (max 30 record). Prefix: Setting the prefix number of the whole numbers that could be into this VoIP gateway (1~20 digits). Drop: Select enable or disable drop prefix function.
Dynamix DW-01Plus/H Gateway User Manual 4.3.13 Password Configuration Screen There are two login accounts in this unit. One is the “root” another is “administrator”. The default passwords for these two accounts are null. Users can define the passwords for these two accounts. Click [Password Configuration] in the navigation panel and open the [Password Configuration] Screen. - Root: The password for the root account. Administrator: The password for the administrator account.
Dynamix DW-01Plus/H Gateway User Manual 4.3.14 Version and Information Screen Users can get more detail about the software version for all the parts in this web page. Click [Version and Information] in the navigation panel and open the [Version and Information] Screen. - Boot Rom: The version of the Boot Rom layer. Application Rom: The version of the Application Rom layer. DSP Application: The version of the DSP Application Rom layer. DSP Kernel: The version of the DSP Kernel layer.
4.3.15 ROM Configuration Screen Dynamix DW-01Plus/H Gateway User Manual Click [ROM Upgrade] in the navigation panel and open the [ROM Configuration] Screen.
4.3.16 Flash Clean Screen Dynamix DW-01Plus/H Gateway User Manual Click [Flash Clean] in the navigation panel and open the [Flash Clean] Screen. - Press CLEAN will clean all configurations of Dynamix DW-01Plus/H and reset to factory default value. Note: User must re-configure all commands all over again (except Network Configure) once execute this function.
Dynamix DW-01Plus/H Gateway User Manual 4.3.17 Commit Configuration Data Screen Click [Commit Data] in the navigation panel and open the [Commit Configuration Data] Screen. - Commit Date to save all configurations. Please remember to commit data before reboot your Dynamix DW-01Plus/H.
Dynamix DW-01Plus/H Gateway User Manual 4.3.18 Reboot Dynamix DW-01Plus/H System screen Click [Reboot System] in the navigation panel and open the [Reboot Dynamix DW01Plus/H Gateway] Screen. - Press reboot will reset Dynamix DW-01Plus/H. Note: To execute reboot, please remember to do Commit Data before Reboot System.
Dynamix DW-01Plus/H Gateway User Manual Part V: Telnet Command Interface This part gives information on how to configure Dynamix DW-01Plus/H gateway via Telnet command line interface.
Dynamix DW-01Plus/H Gateway User Manual 5.1 Login For you first login, enter the login: [root] and default no password. login: root password: Welcome to Terminal Configuration Mode Please enter your configuration item usr/config$ Note: Login account [root] or [administrator] is the default login account and there is no password needed. 5.2 Save and Reboot After any configuration has been made, user has to save all data and reboot system to make configurations take effect. Step 1.
Dynamix DW-01Plus/H Gateway User Manual 5.3 System Commands Overview 5.3.1 [help] Press help/man/ ? will display all command list of Dynamix DW-01Plus/H. The following table lists all of the commands that you can use with the Gateway. Refer to the following chapters for descriptions of commonly used commands. This user’s guide describes commands that are helpful for configuring the Gateway. Using commands not documented in the user’s guide can damage the unit and possibly render it unusable.
5.3.2 [quit] Dynamix DW-01Plus/H Gateway User Manual Type [quit] will quit the Gateway configuration mode. And turn back to login prompt. usr/config$ quit Disconnecting.. login: root Welcome to Terminal Configuration Mode Please enter your configuration item usr/config$ Note: It is recommended that type the [quit] command before you leave the console. If so, Gateway will ask password again when next user connects to console port. 5.3.
- Dynamix DW-01Plus/H Gateway User Manual h323: h323 related information vp: voice related information delete: Remove specified debug flag. open: Start to show debug messages. close: Stop showing debug messages. In this example, user open debug flags including h323, vp, h323vp. usr/config$ debug -add h323 vp h323vp usr/config$ debug –open For example: usr/config$ debug -status Current debug type enabled : Debug Mode is open DEBUG-> H323VP H323 usr/config$ 5.3.
Dynamix DW-01Plus/H Gateway User Manual 5.3.5 [flash] Clean the configuration stored in flash. usr/config$ flash Flash memory information and configuration Usage: flash [-clean] flash -clean Clean the configuration stored. Note: This command will clean the configuration stored in the flash and reboot it. usr/config$ Parameter Usages: - clean: clean all the user defined value, and reboot Gateway in factory default mode.
For example: Dynamix DW-01Plus/H Gateway User Manual usr/config$ flash -clean Flash clean ok!! Rebooting ... Attached TCP/IP interface to cpm unit 0 Attaching interface lo0...done Hardware Type : 1FXS Set RTL8305SB no answer from 192.168.4.114 HTTPD initialized... cmInitialize succeed! Ras port:1024 CallSignal port:1720 AC4804[0] is ok successful 1 2 Initialize OSS libraries...OK! VP v1.44 stack open sucessfully. login: 5.3.6 [commit] Save changes after configuring Gateway.
Dynamix DW-01Plus/H Gateway User Manual usr/config$ ifaddr LAN information and configuration Usage: ifaddr [-print][-mode used][-ip IP Address][-mask Subnet Mask] [-gate Default Gateway][-dns 1 IP Address][-http portnumber] [-dhcpsv used][-nat used][-lanip IP Address][-sntp mode [server]] [-timezone GMT][-ipsharing used IP address][-ipchange used] [-id PPPoE username][-pwd PPPoE password][-reboot used][-emsip EMS IP] [-emsid EMS username][-emspwd EMS password][-emstime EMS digit] -print Display network info
Dynamix DW-01Plus/H Gateway User Manual Parameter Usages: - print: Print current IP setting and status - mode: Specify WAN IP mode (0=Static, 1=DHCP, 2=PPPoE), DHCP mode: Dynamic Host Configuration, PPPoE mode: PPPoE Dial-up function. - ip: Assigned IP address for Gateway mask: Assigned internet subnet mask gate: Assigned IP default gateway autodns: Specify the way to obtain DNS Server (0=Manual, 1=Auto), this function is only usable in DHCP or PPPoE mode. - dns: Setup DNS Server IP Address.
- Dynamix DW-01Plus/H Gateway User Manual pwd: This password is for the user name of the PPPoE usage. reboot: If the connection disconnected by the ISP, the unit will reboot and get the ip again. echo: In the PPPoE mode, if the network connector or the ADSL modem was lost, after the connector and modem connected, it will reboot automatically for - the re-connect with the PPPoE server. emsip: Set the EMS server IP address. emsid: Set the EMS login user name. emspwd: Set the EMS login password.
Dynamix DW-01Plus/H Gateway User Manual usr/config$ ping 192.168.1.2 no answer from 192.168.1.2 usr/config$ ping192.168.1.254 PING 192.168.1.254: 56 data bytes 64 bytes from 192.168.1.254: icmp_seq=0. time=5. 64 bytes from 192.168.1.254: icmp_seq=1. time=0. 64 bytes from 192.168.1.254: icmp_seq=2. time=0. 64 bytes from 192.168.1.254: icmp_seq=3. time=0. ----192.168.1.254 PING Statistics---- ms ms ms ms 4 packets transmitted, 4 packets received, 0% packet loss round-trIP (ms) min/avg/max = 0/1/5 210.63.15.
Dynamix DW-01Plus/H Gateway User Manual usr/config$ sysconf System information and configuration Usage: sysconf [-print][-idtime digit][-forwardtime digit][-keypad used] [-prefixsw used][-prefixdisab used][-usrdefprefix digits] [-codec used][-reverse used][-localrbt used][-roundtrip used] [-gwprefix used][-eod used] sysconf -print Display system overall information and configuration. -idtime Inter-Digits time (1~10 sec). -forwardtime Forward time for FXS line if no answer (5~65535 sec).
- - Dynamix DW-01Plus/H Gateway User Manual according to various applications. In-band: Gateway will transfer DTMF signal via RTP payload. H.245 Alphanumeric via H.245 UII Alphanumeric. H.245 SignalType FXS (VoIP) via H.245 UII Singal Type. Q.931 UserInfo via Q.931 UserInfo. RFC2833 via RFC2833. prefixsw: Switch on/off prefix function. If user enables prefix function, once user dials out, gateway will automatically add prefix number before number user dialed.
Dynamix DW-01Plus/H Gateway User Manual Note: User can also define IP address here in P2P mode, once user press “#”, Gateway will call out this IP address. - dPSTN: This function can let user dial out by PSTN. User just need to press “*#”, the call signal will relay from IP side to PSTN side. For example: usr/config$ sysconf -print System information Inter-Digits time :3 Forward time : 30 Keypad DTMF type : H.
Dynamix DW-01Plus/H Gateway User Manual usr/config$ h323 H.323 stack information and configuration Usage: h323 [-print][-mode used][-gk IP address][-algk IP address][-gwtype used] [-dfgw IP address][-prefix number][-line number][-passwd number] [-alias h323id][-display information][-gkid ID][-gkdis used] -print Display H.323 stack information and configuration. -mode Configure as Gatekeeper mode or Peer-to-Peer mode (0=Gatekeeper, 1=Peer-to-Peer). -gk Gatekeeper IP address.
Dynamix DW-01Plus/H Gateway User Manual Parameter Usages: - print: Print current h323 related settings - mode: Alternatives for gatekeeper or peer-to-peer mode (0=gatekeeper mode; 1=peer-to-peer mode). If users select gatekeeper mode, an extra gatekeeper is needed when Gateway is in operation. - - - - - - - usr/config$ h323 –mode 1 (peer to peer mode) gk: Assign gatekeeper’s IP address when Gateway is in gatekeeper mode. algk: Assign second gatekeeper’s IP address as redundancy.
- Dynamix DW-01Plus/H Gateway User Manual gkfind: Gatekeeper finding port. Which Gateway uses it to discover a gatekeeper. Default value is 1718 (1024~65535). gkras: To set default gatekeeper RAS port number. Default value, is 1719 wellknown port for RAS communication. h225: To set the ras port.(1024~65535) - q931: To set the call signal port.(1024~65535) dstq931: To specify destination H.225 signal port number. range: To allocate port range (1024-19999) Gateway may use it.
Dynamix DW-01Plus/H Gateway User Manual 5.3.12 [line] Line information and configuration. usr/config$ line Gateway line information and configuration Usage: line [-print][-config number [hunt number][hotline number] [forward number]] line -print Gateway line information. -config Set Gateway line information. hunt: Hunting group. hotline: Hot line configuration. forward: No answer forward for FXS line.
For example: Dynamix DW-01Plus/H Gateway User Manual usr/config$ line -print Line information and configuration Index Type Hunt Hotline No Answer Forward Registration Status ============================================================ ==================== 1 FXS 1 x x No Ready usr/config$ 5.3.13 [prefix] This command is for make rules for drop or insert prefix digits.
Dynamix DW-01Plus/H Gateway User Manual usr/config$ prefix Prefix drop/insert information and configuration Usage: prefix [-print] [-add [prefix number][drop used][insert digits]] [-modify index [prefix number][drop used][insert digits]] [-delete index number] prefix -print Display drop/insert information. -add Add new prefix drop/insert information prefix : The prefix of dialed number. drop : Drop prefix (0=Disable, 1=Enable). insert : 1~10 digits.
- Dynamix DW-01Plus/H Gateway User Manual modify: Modify a rule to drop or insert prefix digits of incoming call. usr/config$ prefix –modify 100 drop 0 insert 200 - delete: Delete a rule to drop or insert prefix digits of incoming call. usr/config$ prefix –delte modify 100 drop 0 insert 200 For example: usr/config$ prefix -print Prefix drop/insert information and configuration Index Prefix Drop Insert ======================================================== 1 100 Enable 2000 usr/config$ 5.3.
Dynamix DW-01Plus/H Gateway User Manual usr/config$ pbook Phone book information and configuration Usage: pbook [-print] [-add [name string][e164 number][IP address][port number] [drop used][insert digits]] [-modify number [name string][e164 number][IP address][port number] [drop used][insert digits]] [-delete number] pbook -print Display phone book information and configuration. -add Add new phone book record. name : 1 ~ 20 characters. e164 : 1 ~ 20 digits. ip : IP adress. port : 1024 ~ 65535.
Dynamix DW-01Plus/H Gateway User Manual Parameter Usages: - print: Print out current contents of Phone Book. Users can also add index number, from 1 to 100, to the parameter to show specific phone number. Note: Index number: means the sequence number in phone book. If users do request a specific index number in phone book, Gateway will give each record a automatic sequence number as index. - add: add a new record to phone book.
Dynamix DW-01Plus/H Gateway User Manual 5.3.15 [voice] The voice command is associated with the audio setting information. There are four voice codecs supported by Gateway.
Dynamix DW-01Plus/H Gateway User Manual usr/config$ voice Voice codec setting information and configuration Usage: voice [-print] [-send [G723 ms] [G729 ms] [G729A ms] [G729B ms] [G729AB ms] [G711U ms] [G711A ms] ] voice [-priority [G723] [G729] [G729A] [G729B] [G729AB] [G711U] [G711A] ] [-volume line [voice level][input level][dtmf level]] [-nscng [G711U used1][G711A used2][G723 used3]] [-echo used][-mindelay t1][-maxdelay t2] -print -send Display voice codec information and configuration.
Dynamix DW-01Plus/H Gateway User Manual Parameter Usages: - print: Print current voice information and configurations. - send: To define packet size for each codec. 20/40/60ms means to send a voice packet per 20/40/60 milliseconds. The smaller the packet size, the shorter the - delay time. If network is in good condition, smaller sending packet size is recommended. In this parameter, 20/40/60ms is applicable to G.711u/a law, and G.729 codec, while 30/60ms is applicable to G.723.1 codec.
Dynamix DW-01Plus/H Gateway User Manual usr/config$ voice -print Voice codec setting relate information Sending packet size : G.723.1 : 60 ms G.729 : 60 ms G.729A : 60 ms G.729B : 60 ms G.729AB : 60 ms G.711U : 40 ms G.711A : 40 ms Priority order codec : g7231 g729 g729a g729b g729ab g711u g711a Volume levels : voice volume : 28 input gain : 28 dtmf volume : 23 No sound compress & CNG : G.723.1 : Off G.729 : There is no setting G.729A : There is no setting G.729B : There is no setting G.
Dynamix DW-01Plus/H Gateway User Manual usr/config$ support Special Voice function support manipulation Usage: support [-print][-t38 used][-t38ecm used][-t38asn1 used][-faxrdd digits] [-fstart used][-tunnel used][-h245fs used][-earkyh245 used] [-h450 used] support -print Display support information and configuration. -t38 T.38(FAX) (0=Disabled, 1=Enabled). -t38rq T.38(FAX) Send request Mode.(0=Disabled, 1=Enabled). -t38ecm T.38(FAX) ECM (0=Disabled, 1=Enabled). -t38asn1 T.38(FAX) ASN.
- - - Dynamix DW-01Plus/H Gateway User Manual disable the request mode sending and 1 for request mode sending with the T.38. t38ecm: Enable or disable t38ecm function. The function is support the error correction in the high-speed fax mode. t38asn1: Enable or disable Enable ASN.1 function. The function is support with the FAX. faxrdd: Set fax redundancy depth. User can increase FAX redundancy depth when network traffic is heavy.
Dynamix DW-01Plus/H Gateway User Manual usr/config$ support -print Special Voice function support manipulation T.38(FAX) support : Disabled T.38(FAX) Request Mode : Enabled T.38(FAX) ECM : Disabled T.38(FAX) ASN.1 : Disabled FAX redundancy depth : 0 FastStart support : Disabled Tunneling support : Disabled H.245 message after FastStart support : Enabled EarlyH245 support : Disabled H450 support : Disabled usr/config$ 5.3.17 [sysinfo] This command could show up the line is busy or not.
Dynamix DW-01Plus/H Gateway User Manual usr/config$ phone Phone ringing , ringback tone , busy tone , dial tone setting and notes Usage: phone [-print [ring][rbt][bt][dt][flash]] [-ring [freq ][ringON ][ringOFF ][ringLevel]] [-rbt [freqLo ][freqHi ][freqLoLev][freqHiLev] [Tone1ON][Tone1OFF][Tone2ON ][Tone2OFF ]] [-bt [freqLo ][freqHi ][freqLoLev][freqHiLev] [Tone1ON][Tone1OFF][Tone2ON ][Tone2OFF ]] [-dt [freqLo ][freqHi ][freqLoLev][freqHiLev] [Tone1ON][Tone1OFF][Tone2ON ][Tone2OFF ]] [-flash [freqLo ][freq
Dynamix DW-01Plus/H Gateway User Manual Parameter Usages: - print: Print current call progress tone configurations (ring: ring tone, rbt: ring back tone, bt: busy tone, dt: dial tone). This parameter should be accompanied with tone type. - ring: To set RING tone value. The played tone type, when Gateway is receiving a call. rbt: To set RingBackTone value. The played tone type, when Gateway receives a Q.931 Alerting message. In condition that Gateway is the originate side. - bt: To set BusyTone value.
Dynamix DW-01Plus/H Gateway User Manual Usr/config$ tos IP Packet ToS (Type of Service)/Differentiated Service configuration Usage: tos [-print][-rtptype dscp][-sigtype dscp] tos -print Display IP packet Tos configuration. -rtptype The packages of voice (0~63). -sigtype The package of call signal (0~63). Example: tos -rtptype 7 -sigtype 0 usr/config$ Parameter Usages: - rtptype: the packages of voice (0~63). - sigtype: the package of call signal (0~63).
Dynamix DW-01Plus/H Gateway User Manual usr/config$ ddns The dynamic DNS service information and configuration Usage: ddns [-print][-enable used][-server Address][-hostname Name][-id Account] [-passwd Password][-checkip used][-checkipsrv Address][-delay time] [-force IP] ddns -print Display Dynamic DNS information and configuration. -enable Use the dynamic DNS service(0=Disable, 1=Enabled). -server Specify DDNS server address. -hostname Registered domain name. -id Registered account ID.
- Dynamix DW-01Plus/H Gateway User Manual delay: Enable or disable the service delay time. force: Execute the DDNS function all the times. Note: Support DDNS Server: www.dyndns.org. For example: usr/config$ ddns -print Dynamic DNS service information Status : Enable Server : www.dyndns.org Host Name : totoro609.dnsalias.net ID : totoro609 Password : 123456789 Check IP : Disable IP Check Server1 : checkip.dyndns.org IP Check Server2 : checkip.dyndns.org Delay : Off usr/config$ 5.3.
Dynamix DW-01Plus/H Gateway User Manual usr/config$ pt RTP payload type configuration and information Usage: pt [-print][-rfc2833 type][-dtmf type][-fax type][-faxbypass type] [-modembypass type][-redundancy type][-modemrelayp type] pt -print -rfc2833 Display the RTP payload type information. Configurate the DTMF RFC2833 payload type. -dtmf Configurate the DTMF payload type. -fax Configurate the FAX payload type. -faxbypass Configurate the FAX ByPass payload type.
Dynamix DW-01Plus/H Gateway User Manual usr/config$ rom ROM files updating commands Usage: rom [-print] [-app] [-boot] [-dsptest] [-dspcore] [-dspapp] [-ht] [-method used] [-boot2m] -s TFTP/FTP server ip -f filename rom -print -print show versions of rom files.
- Dynamix DW-01Plus/H Gateway User Manual s: To specify TFTP server’s IP address when upgrading ROM files. f: To specify the target file name, which will replace the old one. method: To decide using TFTP or FTP as file transfer server. [0] stands for TFTP, while [1] stands for FTP. ftp: If users choose FTP in above item, it is necessary to specify pre-defined username and password when upgrading files. For example: usr/config$ rom -print Download Method : TFTP Boot Rom : sdboot.
For example: Dynamix DW-01Plus/H Gateway User Manual usr/config$ auth -print Auth to customized the WEB configuration item for administrator. ifaddr : Enable h323 : Enable line : Disable pbook : Enable support : Disable sysconf : Disable voice : Enable phone : Disable rtp : Disable tos : Disable ddns : Disable prefix : Disable passwd : Enable version : Enable rom : Disable flash : Disable usr/config$ 5.3.
Dynamix DW-01Plus/H Gateway User Manual usr/config$ passwd Password setting information and configuration Usage: passwd [-set [Login name] [Password]][-clean] passwd -set Loginname Password. -clean Clear all password stored in flash. Note: 1. Loginname can be only 'root' or 'administrator' 2. passwd -clean will clear all passwd stored in flash, please use it with care.
Dynamix DW-01Plus/H Gateway User Manual sr/config$ passwd -clean Please wait a moment!! Clean password OK.
