IRT60-212
WARNING: When using electrical products, basic cautions should always be followed, including the following: 1. Read these instructions. 2. Keep these instructions safe. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any of the ventilation openings. Install in accordance with manufacturer’s instructions. 8.
ATTENTION: L’utilisation de tout appareil électrique doit être soumise aux precautions d’usage incluant: 1. Lire ces instructions 2. Gardez ce manuel pour de futures références. 3. Prétez attention aux messages de précautions de ce manuel. 4. Suivez ces instructions. 5. N’utilisez pas cette unité proche de plans d’eau. 6. N’utilisez qu’un tissu sec pour le nettoyage de votre unité. 7.
ACHTUNG: Beim Einsatz von Elektrogeräten müssen u.a. grundlegende Vorsichtsmaßnahmen befolgt werden: 1. Lesen Sie sich diese Anweisungen durch. 2. Bewahren Sie diese Anweisungen auf. 3. Beachten Sie alle Warnungen. 4. Befolgen Sie alle Anweisungen. 5. Setzen Sie dieses Gerät nicht in der Nähe von Wasser ein. 6. Reinigen Sie es nur mit einem trockenen Tuch. 7. Blockieren Sie keine der Lüftungsöffnungen. Führen Sie die Installation gemäß den Anweisungen des Herstellers durch. 8.
CUIDADO: Cuando use productos electrónicos, debe tomar precauciones básicas, incluyendo las siguientes: 1. Lea estas instrucciones. 2. Guarde estas instrucciones. 3. Haga caso de todos los consejos. 4. Siga todas las instrucciones. 5. No usar este aparato cerca del agua. 6. Limpiar solamente con una tela ceca. 7. No blacker ninguna de las salida de ventilación. Instalar de acuerdo a las instrucciones del fabricante. 8.
SPECIFICATIONS IRT60H Supply Voltage (factory preset) ~100V, ~120V, ~220V,~230V, ~240V 50/60Hz Mains Fuse HT Fuse Power Consumption Output Power Rating ~100V/~120V: T5A L 250V ~220V/~230V/~240V: T2A L 250V T500mA L 200 Watts 60 Watts Input Impedance Loudspeaker 1MOhm 2 x Custom designed HH acoustics 12" drivers (16 Ohm) Loudspeaker Outputs 4, 8 or 16 Ohms EQ Per Channel: Passive Bass, Mid, Treble with switchable Deep, Mid Shift & Treble Shift Master Section: Dynamics & Tone Laney-designed digital r
Forged deep within the Black Country - the metal beating industrial heartland of the UK - where the sound of metal guitar was born, comes the IRONHEART. With molten metal flowing through its circuits, IRONHEART continues the legacy passed on by previous Laney amps such as KLIPP and AOR, and hits you hard between the eyes like a power hammer from hell. When cranked, the IRONHEART possesses massive amounts of gain, but is equally at home providing smooth rock and clean tones.
FRONT PANEL CONTROLS (Pull Shift) (Pull Shift) (Pull Deep) 1. INPUT 1/4" mono jack socket. Connect your guitar here. Use only a good quality instrument cable. 2. PRE-BOOST SWITCH Switches the input boost circuit on or off. The Pre-Boost circuit increases the input signal to the preamp tubes, just like placing a boost pedal in your signal path. This drives the preamp tubes harder, resulting in more distortion. This works on both channels. 3.
FRONT PANEL CONTROLS 9. CHANNEL SWITCH Switches between the Lead and Clean/Rhythm channels. 10. CHANNEL LEDS Indicates which channel is currently selected by the Channel Switch (9). 11. CLEAN/RHYTHM SWITCH This switch activates the Clean mode on the Rhythm channel. When operated, the Clean Volume (12) control becomes active, while Rhythm Gain (14) and Rhythm Volume(17) are removed from the signal path. When using clean mode, the preamp gain is lowered, resulting in a cleaner tone. 12.
REAR PANEL CONTROLS IRT60-212 LZB1 2 3 4 N15039 1. MAINS INLET SOCKET Connect to your power source. Make sure the voltage indicated on the rear panel is correct for your country! 2. MAINS FUSE This drawer contains the main safety fuse for the unit. The fuse protects the amplifier from damage in the event of fault by disconnecting the mains power supply. USE ONLY THE CORRECT SIZE AND RATING SPECIFIED ON THE PANEL.
REAR PANEL CONTROLS 5. FX RETURN 1/4" mono jack socket for the connection of the output of an external FX unit. This can also be used as a slave in for the power amp. As the FX Loop is an insert type, this will mute the preamp signal. 6. FX LOOP SWITCH Selects the FX Loop mode of operation: ! Bypass - Removes the FX Loop from the signal path. ! 0 dBu - For connection of FX units with a 0dBu nominal output level. ! -10dBu - For connection of FX units with a -10dBu nominal output level.
QUICK START SETTINGS Set to preference Clean (Pull Shift) (Pull Shift) (Pull Deep) (Pull Shift) (Pull Shift) (Pull Deep) Lead Rock Rhythm Lead Metal (Pull Shift) Rhythm Lead Detuned Metal Rhythm (Pull Shift)
USER SETTINGS (Pull Shift) (Pull Shift) (Pull Deep) (Pull Shift) (Pull Shift) (Pull Deep) (Pull Shift) (Pull Shift) (Pull Deep) (Pull Shift) (Pull Shift) (Pull Deep)
TUBE AMP TIPS Tube amplifiers generally sound much warmer/sweeter than solid state transistor amplifiers but they also need a little more respect due to the fragile glass tubes. The Ironheart combo uses four 12AX7 preamp tubes, and two 6L6 output tubes which should give you years of trouble free service, however like all tube amps; it is important to treat it with a certain amount of care. Use the following steps as a guide for how to take care of your amplifier: ! Take care when moving the amplifier.
LINE OUT FX SEND BLOCK DIAGRAM FX RETURN TREBLE SHIFT BYPASS 0 dBu -10dBu REVERB REVERB LEVEL Footswitch TREBLE LEAD VOLUME TREBLE SHIFT RHYTHM GAIN MID SHIFT BASS DEEP LEAD GAIN MID LEAD EQ Pre-Boost TREBLE BASS MID CLEAN/RHYTHM EQ CLEAN VOLUME RHYTHM VOLUME CLEAN/RHYTHM 16Ohms 8Ohms/2x16Ohms Watts Dynamics Master section controls Tone INPUT MID SHIFT DEEP LEAD/RHYTHM 4Ohms/2x8Ohms EXTERNAL LOUDSPEAKER 4-16 OHMS INTERNAL LOUDSPEAKERS 2 x 16 OHMS
SAMPLE SETUP FX UNIT GUITAR Internal Speakers IRT60-212 LZB1 2 3 4 N15039 FS4-IRT
FX UNIT GUITAR Internal Speakers IRT60-212 LZB1 2 3 4 N15039 IRT212 FS4-IRT
OPERATING INSTRUCTIONS - Issue 1.