User Manual

ManualsBrandsDynaScan ManualsFanless SignageDynaScan DI551ST2 55 Inch Fanless Signage

User Manual

DI551ST2

Version 2.10

The use of diagrams and illustrations in the manual are for reference only. The actual product may be different.

Product design and specifications are subject to change without notice

Summary of content (28 pages)

PAGE 1
User Manual DI551ST2 Version 2.10 The use of diagrams and illustrations in the manual are for reference only. The actual product may be different.
PAGE 2
Contents Material Contents Declaration ................................................................................................................ 2 Recycling and Energy Information ......................................................................................................... 2 Declaration of Conformity ....................................................................................................................... 3 Safety Precautions ..................................................
PAGE 3
Material Contents Declaration Hazardous Substances Hexavalent Polybrominated Polybromodiphenyl Part Name Lead Mercury Cadmium Chromium Biphenyls Ethers Pb Hg Cd Cr6+ PBB PBDE PCBA O O O O O O CHASSIS O O O O O O ACCESSORY O O O O O O PACKAGE O O O O O O “O” indicates that the level of the specified chemical substance is less than the threshold level specified in the standards of SJ/T-11363-2006 and EU 2005/618/EC.
PAGE 4
Declaration of Conformity FCC This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
PAGE 5
Safety Precautions CAUTION Do not install near flammable material or any heat sources. Do not defeat the safety purpose of the grounding-type plug. Do not disassemble the display to avoid electrical shock or burn. Normal operating condition considers installation at an altitude below 2000m; some abnormalities may be experienced when installed at an altitude above 2000m. The power should be turn off during inserting or removing SD card.
PAGE 6
Important Safety Information             Disassembling the LCD is strictly prohibited. Opening the cover may expose the user to electric shock or other hazards. Please contact DynaScan certified service professionals for all maintenance requirements. Do not allow any liquid to enter the LCD. Also avoid placing the LCD close to water sources. Do not place heavy objects on the power cord. A damaged power cord might cause electric shock or fire. Do not bend, twist, or damage the power cord.
PAGE 7
Getting Started Contents Confirm that the accessories below are shipped along with the display. If any item is missing, please contact your dealer. The color and shape of the accessories may vary with the products.    DI551ST2 Professional LCD. Remote Control x 1 pc. Batteries (1.5V / AAA) x2 pcs.   Power cable x1 pc. Quick Start Guide x1 pc. Attention: Please use the following table to check whether the included power cord is suitable for your region.
PAGE 8
Installation The LCD must be properly installed using a wall mount. Incorrect installation may cause injury or damage the equipment. Product warranty does not cover the damage caused by improper installation and DynaScan shall not be held responsible in such incident. Refer to the mount manufacturer’s instructions for proper installation. Mounting    Hanging the Professional LCD from the ceiling or mounting it on the wall is the responsibility of the user.
PAGE 9
Orientation  When used in the portrait orientation, the LCD should be rotated clockwise when looking at the front of the display such that the left edge becomes the top edge. Portrait mode: Rotate the set clockwise 90° (mandatory) Portrait mode: Rotate the set counterclockwise 90° (mandatory)  The orientation sticker can be found on the rear of display, which is for distinguishing the direction of installation.
PAGE 10
Installation Location  The wall and mount must have enough strength to support the LCD and its accessories.  Do not install in a location with strong vibrations or is dusty.  Do not install near the building’s main electric panel.  Ensure the LCD is secured in such a manner that it cannot be easily removed by the general public.  Leave clearance around the outer edge of the LCD (or video wall matrix) from other objects to ensure proper ventilation.
PAGE 11
Maintenance  Inspect the fasteners regularly for signs of loosening or deformation. Please perform appropriate corrective measures when a problem is identified. Neglecting the problem may worsen the situation.  Increase the inspection frequency on areas where previous maintenance had occurred to ensure the problems do not occur again. Wall Mounting     A wall mount is not included. Please purchase a VESA Standard wall mount to secure the LCD.
PAGE 12
Connecting to a Power Source Using the power cable provided, plug it in the power inlet on the back of the display shown in the diagram below. Connect the power cable to a 100-240 volt, 50 / 60Hz AC power outlet. Insert the plug completely into the socket. A loose power connection may cause damage to the display and/or lead to a fire hazard.
PAGE 13
Connecting an External Video Source Turn OFF the power of both LCD and external video device. Using the DVI cable (or DP cable, HDMI cable) provided, insert one end into the DVI-IN (or DP-IN, HDMI-IN) on the back of the display shown the in the diagram below. Connect the other end of the DVI cable (or DP cable, HDMI cable) to the DVI output (or DP output, HDMI output) of the video source. Refer to your video device’s manual for additional information.
PAGE 14
Input / Output Terminals AC (IN): Connect the supplied power cord to the wall outlet. Power Switch: Press to switch the main power on/off. Audio (OUT): Connect the audio signal output from Audio IN jack to an external AV device. Thermal: Extension Connector for optional Extension thermal kit (ETK201). Extension Connector: Extension Connector for optional IR Extension sensor kit (ESK302). DP (IN): Connect the DP output of a PC, or the DP output of an AV device via a DP cable.
PAGE 15
Operating Instructions Powering On/Off the Display To turn on/off the display, press the power switch on the back of the display as shown in the diagram below. ON OFF NOTE: The remote control only works when the power switch is ON.
PAGE 16
Using the Remote Control  When using the remote control, aim the remote at the IR receiver on the display. The IR receiver on the DI551ST2 model is at the back of the display with a receiving angle of 100 degrees. The IR receiver configurations of the model are shown in the figure below.  The operating range of the remote control is 2.5 meters (8 feet).  Ambient light may affect the performance of the remote control. in the vicinity.
PAGE 17
        *Color and shape may vary by model. ITEM         DESCRIPTION POWER MENU UP LEFT RIGHT DOWN OK BACK Power On / Off OSD On / Off Move the cursor up or change the setting of selected item. Exit the current selection. Select the highlighted item. Move the cursor down or change the setting of selected item. Enter (for DSM365 only) Return to the last page.
PAGE 18
Using the Rear Panel Controls ITEM DESCRIPTION MENU UP DOWN LEFT RIGHT OSD On / Off, Power On / Off. Move the cursor up or change the setting of selected item. Move the cursor down or change the setting of selected item. Exit the current selection. Select the highlighted item.
PAGE 19
Navigating the On Screen Display (OSD) Menu Press the MENU button on either the rear panel control or remote control to show the OSD. navigation arrows to select and adjust the menu items. ITEM 1 ITEM 2 DEFAULT DESCRIPTION Input Source Main Failover 1 Failover 2 Failover 3 HDMI DP DVI DSM365 Set the Main input to display. Set the Failover 1 input to display. Set the Failover 2 input to display. Set the Failover 3 input to display.
PAGE 20
ITEM 1 Time ITEM 1 ITEM 2 DEFAULT DESCRIPTION Current Date YYYY:MM:DD Current Time HH:MM:SS HH:MM HH:MM Set the date. Set the clock. Note: The internal clock will continue to function when the power is turned off. Turn on / off automatic power schedule function. Set turn-on time. Set turn-off time.
PAGE 21
ITEM 1 ITEM 2 DEFAULT Display Mode Auto Screen Protection Off IR Control On Power Off Mode Standby Volume 100 Reset to Default Setting Off ITEM 1 ITEM 2 DEFAULT Information 1 Resolution Model Serial Number Hardware Firmware Color Depth Advance DI551ST2 DESCRIPTION Change the Menu orientation. The Menu can be displayed in either LANDSCAPE or PORTRAIT mode. Turn on / off image burn-in protection. Set image burn-in protection interval. Range 1 – 100.
PAGE 22
ITEM 1 ITEM 2 Information 2 Temperature (BLU) Temperature (Amb.) ALS Level (Amb.) ITEM 1 ITEM 2 Information 3 Over Heat Protection DEFAULT DESCRIPTION LCD inner (backlight unit) temperature monitoring. LCD outer (ambience) temperature monitoring. (temperature sensor installation is necessary) The brightness of ambience monitoring. (Ambience Light Sensor) DEFAULT DESCRIPTION Inactive It will enter into protection mode when the display internal temperature is over heat. 60°C = Brightness 50%.
PAGE 23
Specifications MODEL PANEL POWER MECHANICAL SPECS USER INTERFACE ENVIRONMENT I/O Ports Fuse DI551ST2 LCD Panel Size Native Resolution Brightness Contrast Ratio Response Time Viewing Angle Life Time Panel Surface Power Supply Rated Voltage Power On Mode Standby Mode Bezel Width (T/B/L/R) Cabinet Color Monitor Dimension (LxHxD, w/o Stand) Monitor Weight (set / package) VESA Mounting (Dimension) 54.64 inches 1920 x 1080 1000 cd/m² (Typ.) 3,000:1 9 ms (Typ.) 178°/ 178° 50,000 hrs (Typ.) AR Haze 1.
PAGE 24
Input Mode Active Resolution H Pixels V Lines 640 720 800 1024 1280 1280 1360 1920 480 480 600 768 720 768 768 1080 Refresh Rate Pixel Rate Aspect Ratio 60 Hz 59.94 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 25.175 MHz 27 MHz 40 MHz 65 MHz 74.25 MHz 79.5 MHz 85.5 MHz 148.
PAGE 25
Pin Assignments Digital RGB Input (DVI-D): DVI PIN ASSIGNMENT OF DVI CONNECTOR 01 02 03 04 05 06 07 08 RX2RX2+ Shield (RX2 / RX4) NC NC DDC-Serial Clock DDC-Serial Data NC 09 10 11 12 13 14 15 16 RX1RX1+ Shield (RX1 / RX3) NC NC +5V power Ground Hot plug detect 17 18 19 20 21 22 23 24 RX0RX0+ Shield (RX0 / RX5) NC NC Shield (RXC) RXC+ RXC- RS-232 Input PIN No.
PAGE 26
Troubleshooting ISSUE RECOMMENDED SOLUTION   No image is displayed. Nothing happens when switching the main switch on. Image is unstable. The remote control does not work. Auto on/off does not work or does not function properly. Cannot control the display remotely via RS-232.            Check whether the cable is completely plugged in. Check whether the main switch is in the ON position, and the power cord is completely plugged in.
PAGE 27
About DSM365 DSM365 is an internal operating system as Android, which can install the applications via USB flash drive storage, SD card or Internet. How to Switch to DSM365   Press the MENU button on either the rear panel control or remote control to show the OSD. Use the navigation arrows to select and adjust the Input Source. [Input Source → Main → DSM365]  ITEM    DESCRIPTION APPS SETTINGS Show the Installed APPS. Enter the setting menu.