Homeowner’s Installation Instructions & Operating Manual Model: DY-BEF37 DY-BEF45 DY-BEF57 DY-BEF64 DY-BEF80 Please read the instructions carefully before installation or use of this electric fire and retained for future reference. Dynasty Fireplaces #10-3071 No.
Contents Important safety information .........................................................................................3 Appliance data ..............................................................................................................5 Product dimension ........................................................................................................5 Packing list ....................................................................................................................
IMPORTANT SAFETY INFORMATION! WARNING Read all instructions before using this heater! This heater is hot when in use. To avoid burns, DO NOT let bare skin touch hot surfaces. If provided, use handles when moving this heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9m) from the front of the heater, and keep them away from the sides and rear.
WARNING WARNING: REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK---DO NOT USE THIS HEATER WITH ANY SOLID STATE SPEED CONTROL DEVICES. For residential use only! NOT for commercial use! Any commercial or public use of this heater voids all warranties, and could cause injury. This product is not intended to be a primary heat source. It is for supplemental heat only.
APPLIANCE DATA Model No. EF206-210B (BEF37-80) Supply Voltage AC 120V 60Hz Heating Element 1500W Mains Cable 1 x 2.0m (approx) Maximum power consumption: 1500W Power for flame effect: EF206B (BEF37) 9W+8W EF207B (BEF45) 10.4W+8W EF208B (BEF57) 15W+8W EF209B (BEF64) 17.2W+8W EF210B (BEF80) 26.7W+8W Power for Fuel Bed: EF206B(BEF37) EF207B(BEF45) EF208B(BEF57) EF209B(BEF64) EF210B(BEF80) 5.8W 5.8W 8.6W 8.6W 10.
PACKING LIST C-AAA Battery (2) A - Fireplace (1) B-Remote Control (1) D-Small and Large Crystal Stones (1 set) E-Log (1 set) F- ST 4*8 Metal Screws (8) H- ST 4*12 Metal Screws (4) I- Owner’s Manual (1) G- Fixing Brackets (4) INSTALLATION LOCATING YOUR ELECTRIC FIREPLACE Your new electric fireplace may be installed virtually anywhere in your home. However, when choosing a location, ensure that the general instructions are followed. For best results, install out of direct sunlight.
Choose a fireplace location and frame as shown in figure 1. units: mm MODEL W EF206B EF207B EF208B EF209B EF210B (BEF37) (BEF45) (BEF57) (BEF64) (BEF80) 938 1138 1438 1638 2038 Figure 1 Take out the 4 fixing brackets and 8pcs ST4X8 screws to fix on the left and right side panel of the unit. Figure 2 Use 4 ST4*12 screws to fix the fireplace on the frame as shown in figure 3.
Figure 3 Take out the trim gently, take out the screw M5*12 on both sides, and use glass hook to take out the glass carefully as shown in figure 4 and figure 5.
Figure 5 Set the fuel bed For crystal effect: Carefully spread the small clear crystal stones across the fuel bed. Then evenly arrange the larger crystal stones along the inset window ledge at the front of the firebox. For log effect: Arrange the logs. Below arrangement in the picture for your reference. Place the small semi-painted and clear crystal stones in between the log layout.
The fireplace is packaged with a three prong plug installed for plug-in convenience. Hard wiring the fireplace is also an option for any installation. Plug in (you may run the power cord out of the framed wall opening to an existing outlet or install an outlet on a nearby wall stud within the wall). If the cord is not long enough to reach the outlet, a grounded extension cord minimum AWG No. 14 wiring and rated to a minimum or 1875 watts may be used. Hard wire the fireplace (recommended).
Main power switch The POWER switch supplies power to all of the functions of the fireplace. This switch must be in the “ON” position for any of the functions including the remote to work. Power button By pressing the POWER button, turn the fireplace on when it is off or turn it off when it is on. Flame button By pressing the FLAME button, the unit will cycle through five flame effects. Fuel bed button By pressing the FUEL BED button to cycle through 14 fuel bed effects.
Multifunction Infrared Remote Handset BUTTON ON/OFF FUNCTION ACTION & INDICATION ON: Turns on. Note: All the functions are off in the standby mode, it will memorize the working condition of flame effect and heating. OFF: Returns the unit to standby mode. 1. Press. The flame effect and the remote control functions are enabled. The flame setting will display on the remote control screen. 2. Press. The flame effect and all the functions will turn off. The remote control screen will go blank.
CARE AND MAINTENANCE ALWAYS turn the heater OFF and unplug the power cord from the outlet before cleaning, performing maintenance, or moving this fireplace. Failure to do so could result in electric shock, fire, or personal injury. Cleaning NEVER immerse in water or spray with water. Doing so could result in electric shock, fire, or personal injury. Metal: Buff using a soft cloth, slightly dampened with a citrus oil-based product.
WARRANTY In the unlikely event of a problem occurring due to a manufacturing fault within 24 months from the date of purchase of the appliance it will be repaired or replaced free of charge. This warranty does not cover consumable items such as the bulbs and fuses which have a limited lifespan. If a problem should occur, the nature of the problem together with the date of a purchase should be immediately reported to the retailer that the appliance was purchased from.