Owner`s manual

5000 Top Side Control Instructions
Filtration starts as soon as flow is steady through the filter. The filter
cartridge removes the dirt from the spa water, the accumulated dirt
causes flow resistance. A dirty cartridge will decrease flow and may
cause spa not to heat properly. Therefore, regular filter cleaning is
important.
Cleaning and Replacing Filter Cartridge (100 sqft.)
For Baron 3000 owners (50 sqft.)
Your Dynasty Spa filter has been designed for quick and easy maintenance.
Turn off power at the breaker.
Open filter door and expose filter cartridges by pulling door toward center
of spa until door opens all of the way out.
Clean with a garden hose equipped with a high pressure nozzle,
or soak in filter cartridge cleaner if necessary or at every other
regularly scheduled cleaning. Rinse filter thoroughly before installing.
Screw clean cartridge back into filter enclosure and return filter door to
original position
Replace basket weir in filter canister
Unscrew filter cartridges and remove.
Filter Maintenance
Note: The filter should be inspected
and cleaned on a monthly basis.
16
21
7
Lock
icon
Temperature
unit
Programming Mode
icon
Filter Cycle
icon
Heater
icon
Economy Mode
icon
Up & Down
arrows
Step 1
Step 2
Step 3
Step 4
Time of day
Filter cycle start time
Filter cycle duration
Filter cycle frequency
Step 5
Economy mode start time
Step 6
Economy mode duration
Step 7
Storing settings in memory & returning to Normal mode
Step 1- Time of day
Setting the time:
1- Enter Programming mode by holding
Prog. key pressed down for 2 seconds.
2- The display will show the current
setting.
3- Use Up and Down arrows to change
11:43 pm
10:25 am
The system automatically performs two filter
cycles per day, at 12-hour intervals. During the filter
cycle, Pumps 1 & 2 and the blower will run for one
minute, then Pump 3 will run for one minute.
Pump 1 will then run at low speed for a programmed
number of hours. The "Filter Cycle" icon lights up
when a filter cycle is on.
To program a filter cycle, you must enter: 1) the
time you want the cycle to start and 2) the duration
of the cycle. If no filtering is required, the duration
should be set to "0". For continuous filtering, the filter
cycle duration should be set to "12:00".
Setting filter cycle start time:
1- Press Prog. key a second time.
2- The display will show FSxx, with "xx"
representing the starting hour.
3- Use Up and Down arrows to change
setting.
Setting filter cycle duration:
1- Press Prog. key a third time.
2- The display will show Fdxx, with "xx"
representing the duration in hours.
3- Use Up and Down arrows to change
setting.
Steps 2 & 3- Filter cycle start time &
duration
FS08
FS10
Fd06
Fd04
Setting filter cycle frequency:
 1- Press Prog. key a fourth time.
 2- The display will show FFxx, with
"xx"
 representing the frequency per
day.
Step 4- Filter cycle frequency
FF10
FF06
Step 7- Storing settings in
Press Prog. key a seventh time to store the settings in
the system's non-volatile memory and to return to
Normal mode.
Steps 5 & 6- Economy mode start time
&
Setting Economy mode start time:
 1- Press Prog. key a fifth time.
 2- The display will show ESxx, with "xx"
 representing the starting hour.
 3- Use Up and Down arrows to change
 setting.
Setting Economy mode duration:
 1- Press Prog. key a sixth time.
 2- The display will show Edxx, with "xx"
 representing the duration in hours.
 3- Use Up and Down arrows to change
 setting.
ES08
ES10
Ed06
Ed04
Step
Programming
Sequence
Turn off power at the breaker.
Remove basket from filter canister, remove filter cartridge and clean
with a garden hose equipped with a high pressure nozzle, or soak in
filter cartridge cleaner if necessary or at every other regularly scheduled
cleaning. Rinse filter thoroughly before installing.
Place clean cartridge in filter canister