DVD +/- R/RW Writer DVD+/-R 8X/ DVD+/-RW 4X User’s Manual
CLASS 1 LASER PRODUCT APPAREIL A LASER DE CLASSE 1 LASER KLASSE 1 LUOKAN 1 LASERLAITE PRODUIT LASER CATEGORIE 1 DANGER VORSICHT INVISIBLE LASER RADIATION WHEN OPEN AVOID DIRECT EXPOSURE TO BEAM INSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GEÖFFNET NICHT DEM STRAHL AUSSETSEN ATTENTION RADIATION DU FAISCEAU LASER INVISIBLE EN CAS D’OUVERTURE. EVITER TOUTE EXPOSITION AUX RAYONS.
FCC Compliance Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. this device may not cause harmful interference, and 2. this device must accept any interference received, including interference that may cause undesired operation. FCC Warning Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Table of Contents INTRODUCTION SYSTEM REQUIREMENTS INSTALLATION HOST INTERFACE CONNECTIONS HARDWARE INSTALLATION DRIVER INSTALLATION Windows Environment SOFTWARE PACKAGE Installation Under Windows Environment CONNECTION & OPERATION FRONT PANEL REAR VIEW DVD REGION CODING REGION PLAYBACK CONTROL MANAGEMENT REGION CODES About This Drive 1 2 3 3 4 5 5 6 6 7 7 8 9 9 9 10 TECHNICAL DATA 11 APPENDIX 13
DVD +/- R/RW Writer INTRODUCTION Welcome to a multimedia world of ReWritable technology with DVD burning capabilities. This multiformat recordable drive presents you more backup choices other than acting as a CD-R/RW drive and as a DVD-ROM reader. The drive supports DVD Forum’s DVD-R/-RW standard as well as that of DVD+RW Alliance’s DVD+R/+RW enabling excellent compatibility, simple, quick recording of both CD/DVD formats, huge capacity storage, and theater-quality playback.
DVD +/- R/RW Writer System Requirements For IBM compatible PCs, the system requirements recommended are as follows: 2 ♦ Pentium III, 800MHz or above with at least 256MB of memory ♦ Minimum 2GB free Hard Disk space ♦ IDE host interface supporting ATAPI MMC command ♦ Operating system: Microsoft Windows 98SE/ME/2000/XP
DVD +/- R/RW Writer INSTALLATION Host Interface Connections Most current mainboards have two IDE ports (primary and secondary), which can connect two IDE cables. Two IDE cables allow you to connect up to four devices, but it is recommended that you separate IDE ports for your hard drive and this writer. This will ensure that your hard drive’s performance and speed won’t be affected by having the writer on the same cable.
DVD +/- R/RW Writer Hardware Installation 1. Turn off the power to the computer system. 2. Disconnect all cables from the back of your computer, and then remove the cover from the computer. 3. Insert the writer into one of the vacant 5.25" drive bays and secure it with screws to your PC. In order to prevent interference between the writer and the computer, please mount the writer using all four mounting screws. 4.
DVD +/- R/RW Writer If your mainboad is integrated with built-in sound system, plug the 4-pin audio cable into the CD-IN connector on the mainboard as Audio-in. 6. Re-attach the cover of your computer, and reconnect the power cord. Driver Installation Windows Environment This DVD±R/RW Writer is a Plug & Play device and there is no need to install driver. Windows 98SE/ME/2000/XP can automatically detect the drive and load the appropriate driver.
DVD +/- R/RW Writer Software Package The bundled package combines software for 1) DVD/CD recording 2) DVDs/VCDs authoring 3) Packet Writing 4) DVD playback, which gives you the complete solution for making audio/data CDs/DVDs of different formats, editing video and authoring DVD movies. The user-friendly interface simplifies the recording process and guides you through the creation in an easy and innovative way.
DVD +/- R/RW Writer CONNECTION & OPERATION Front Panel 1. LED Indicator (dual color) Flashes “green” while verifying or reading a disc. Flashes “amber” while writing discs. 2. Disc Tray Place the disc in the tray here, and then press the Close/Eject button or lightly push the tray to close it. 3. Emergency Eject Hole If the Close/Eject button doesn’t work properly and the disc tray can’t be opened, you can insert a paper clip or a small rod into this hole for manual ejection.
DVD +/- R/RW Writer Rear View 1. Digital Audio Output Connector If your sound card has a digital audio IEC958 format connector, you can connect it to this digital audio output connector with a 2-pin audio cable. 2. Analog Audio Output Connector This connector allows you to connect the drive to your sound card with a 4pin audio cable. 3. Device Configuration Jumper Set the jumper to Master, Slave or Cable Select according to your system configuration. 4.
DVD +/- R/RW Writer DVD REGION CODING Region Playback Control Management All DVD Video Playback systems have “Region Playback Control” (RPC) which is required by Hollywood movie industry and defined by DVD Forum. You can only play DVD-Video discs with the same region code as your DVD-Video Playback system. As for DVD-ROM drives, one kind of the DVD-Video Playback system, there are 2 types: RPC Phase 1 (as RPC1): RPC1 drives do not have built-in hardware support for region management.
DVD +/- R/RW Writer About This Drive This DVD±R/RW Writer is also a RPC2 DVD-ROM drive and the first region code will depend on the DVD title you play. You are allowed to modify the region code 5 times (including the initial one). After the fifth alteration, the region code will be locked and only those DVD titles of the same region code could be played afterwards, so set the code carefully.
DVD +/- R/RW Writer TECHNICAL DATA Interface E-IDE/ATAPI Disc Data Capacity DVD+/-R, DVD+/-RW: Single layer 4.
DVD +/- R/RW Writer Data Transfer Rate CD -- Read CD-ROM/CD-R: 6000KB/sec (up to 40X) CD-RW: 4800KB/sec (up to 32X) CD -- Write CD-R: 6000KB/sec (up to 40X) CD-RW: 3600KB/sec (up to 24X) DVD -- Read DVD-ROM: 16224KB/sec (up to 12X) DVD -- Write DVD+/-R: 10816KB/sec (up to 8X) DVD+/-RW: 5408KB/sec (up to 4X) Access time DVD: CD: Data buffer 2MB Disc loading Tray (motorized) Dimensions (WxHxD) 148.6 x 41.8 x 193.
DVD +/- R/RW Writer APPENDIX DVD Forum The DVD Forum is an international organization made up of companies using or manufacturing digital versatile disc (DVD)-related products. The Forum was created in 1995 when ten companies (Hitachi, Matsushita, Mitsubishi, Philips, Pioneer, Sony, Thomson Multimedia, Time Warner, Toshiba Corporation, and Victor) joined for the common purpose of promoting DVD worldwide and establishing standardized formats of each DVD application for the marketplace.
DVD +/- R/RW Writer DVD Formats DVD Video Popular format for viewing movies and other visual entertainment with high quality MPEG2 video & digital surround sound. Enables multi-language, multi-subtitling and other advanced user features. DVD Audio This audio-only storage format doubles the fidelity of sound effect comparing with a standard CD as well as longer playing times, copy protection and anti-piracy measures…etc.
DVD +/- R/RW Writer Reference For more related information about the organizations and formats definition of DVD, please refer to the following web sites: http://www.dvdrw.com http://www.dvdforum.org http://www.licensing.philips.com http://www.disctronics.co.uk http://www.dvdfllc.co.
Graveur deDVD +/- R/RW DVD+/-R 8X/ DVD+/-RW 4X Guide de l’utilisateur
CLASS 1 LASER PRODUCT APPAREIL A LASER DE CLASSE 1 LASER KLASSE 1 LUOKAN 1 LASERLAITE PRODUIT LASER CATEGORIE 1 CAUTION CLASS 3B VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN. AVOID DIRECT EXPOSURE TO BEAM. VORSICHT KLASSE 3B SICHTBARE UND UNSICHTBARE LASERSTRAHLUNG WENN GEOFFNET. NICHT IN DEN STRAHL SEHEN. ATTENTION RADIATION DU FAISCEAU LASER VISIBLES ET INVISIBLES DE CLASSE 3B EN CAS D'OUVERTURE.
Déclaration de Conformité FCC Cet appareil est conforme aux directives de l'Article 15 des Réglementations de la FCC. Son opération ets sujette aux deux conditions suivantes: 1. Cet appareil ne doit pas provoquer d'interférence néfaste et 2. Cet appareil doit accepter toute interférence reçue, y compris les interférences provoquant une opération indésirable.
Table de matières INTRODUCTION 1 BESOINS SYSTEME 2 INSTALLATION 3 CONNEXIONS DE L’INTERFACE HOTE INSTALLATION DU MATERIEL INSTALLATION DU LECTEUR Environnement Windows PROGICIEL Installation sous environnement Windows 3 4 5 5 6 6 CONNEXION & FONCTIONNEMENT 7 PANNEAU AVANT VUE ARRIÈRE CODAGE REGIONS DVD GESTION DE LA COMMANDE DE LECTURE REGIONALE.
Graveur DVD +/- R/RWr INTRODUCTION Bienvenue dans le monde multimédia de la technologie réinscriptible dotée de capacités DVD ardentes. Outre le rôle de lecteur CD-R/RW et de lecteur DVD-ROM, ce graveur DVD ± R/RW multi formats vous offre plus de choix en matière de sauvegarde.
Graveur DVD +/- R/RW Besoins système Pour les PC compatibles IBM les besoins système recommandés sont les suivants : 2 ♦ Pentium III, 800MHz ou supérieur avec une mémoire de 256MB au minimum. ♦ 2GB d'espace libre sur le disque ♦ Une interface hôte IDE supportant la commande ATAPI MMC.
Graveur DVD +/- R/RWr INSTALLATION Connexions de l’interface hôte La majorité des cartes mères actuelles sont équipées de ports IDE (primaire et secondaire) qui peuvent connecter deux câbles IDE. Deux câbles IDE vous permettent de conencter jusqu’à quatre périphériques, mais il est recommandé de séparer les ports IDE de votre disque dur et de ce graveur. Cela garantira que la performance et la vitesse de votre disque dur ne seront pas affectées par le fait que le graveur est sur le même câble.
Graveur DVD +/- R/RW Installation du matériel 3. Eteignez l’ordinateur. 4. Débranchez tous les cables à l’arrière de l’ordianteur puis, retirez le couvercle de l’ordinateur. 3. Insérez le graveur dans l’un des chassis de lecteur 5.25" libres puis fixez-le à votre PC à l’aides de vis. Pour éviter toute interférence entre le graveur et l’ordianteur, veuillez assembler le graveur au moyen des quatre vis de montage. 4.
Graveur DVD +/- R/RWr Si votre carte-mère est équipée d’une carte son intégrée, branchez le câble audio 4 broches dans le connecteur CD-IN de la cartemère comme entrée Audio. 7. Remettez le couvercle de l’ordinateur et rebranchez le cordon d’alimentation. Installation du lecteur Environnement Windows Ce graveur DVD±R/RW est un périphérique Plug & Play et il n’y a pas besoin d’installer de pilote. Windows 98SE/ME/2000/XP peut détecter automatiquement le lecteur et charger le pilote approprié.
Graveur DVD +/- R/RW Progiciel L’offre logiciel inclut les logicicels 1) d’enregistrement DVD/CD 2) de création de DVD/VCD 3) d’écriture en paquets 4) de lecture DVD, qui vous offrent la solution complète pour faire des CD/DVD audio ou de données de différents formats, d’éditer des vidéos et de créer des films DVD. L’interface conviviale simplifie le processus d’enregistrement et vous guide tout au long de la création d’une manière facile et innovante.
Graveur DVD +/- R/RWr CONNEXION & FONCTIONNEMENT Panneau avant 1. Indicateurs DEL (deux couleurs) Clignote en ‘’vert’’ pendant la vérification ou la lecture d’un disque. Clignote en ‘’jaune’’ pendant le gravage des disques. 2. Plateau à disque Placez le disque dans ce plateau, puis appuyez sur le bouton Fermer/Éjecter ou poussez légèrement sur le plateau pour le fermer. 3.
Graveur DVD +/- R/RW Vue arrière 1. Connecteur numérique sortie Audio Si la carte son est dotée d'un connecteur de format audio numérique IEC958 vous pouvez la brancher au connecteur de sortie audio numérique au moyen d’un câble audio à 2 broches. 2. Connecteur de sortie Audio analogique Ce connecteur vous permet de brancher le lecteur à votre carte son au moyen d’un câble audio à 4 broches. 3.
Graveur DVD +/- R/RWr CODAGE REGIONS DVD Gestion de la commande de lecture régionale. Tous les systèmes de lecture video de DVD sont equipés d’une ‘’commande de lecture régionale’’ (RPC) exigée par l’industrie du film hollywoodienne et définie par le Forum DVD.
Graveur DVD +/- R/RW A propos de ce lecteur Ce graveur DVD±R/RW est également un lecteur RPC2 DVD-ROM et le premier code de zone régionale dépend du titre du DVD lu. Vous êtes autorisé à changer la région 5 fois (y compris la région initiale). Au bout de la cinquième modification, le code de région est verrouillé et seuls les titres de DVD de la même région pourront être lus, par conséquent, réglez attentivement le code.
Graveur DVD +/- R/RWr DONNEES TECHNIQUES Interface E-IDE/ATAPI Capacité du disque de données DVD+/-R, DVD+/-RW: Une couche 4.
Graveur DVD +/- R/RW Taux de transfert de données CD -- Lecture CD-ROM/CD-R: 6000KO/sec (jusqu’à 40X) CD-RW: 4800KO/sec (jusqu’à 32X) CD -- Ecriture CD-R: 6000KO/sec (jusqu’à 40X) CD-RW: 3600KO/sec (jusqu’à 24X) DVD -- Lecture DVD-ROM: 16224KO/sec (jusqu’à 12X) DVD -- Ecriture DVD+/-R: 10816KB/sec (jusqu’à to 8X) DVD+/-RW: 5408KB/sec (jusqu’à 4X) Temps d’accès DVD: 160ms (12X) CD: 130ms (40X) Tampon données 2MB Chargement du disque Plateau (motorisé) Dimensions (LxHxprofondeur) 148.6 x 41.
Graveur DVD +/- R/RWr APPENDICE Forum DVD Le forum DVD est une organisation internationale constituée d’entreprises utilisant ou fabriquant les produits relatifs aux disques numériques polyvalents (DVD).
Graveur DVD +/- R/RW Formats DVD DVD Vidéo Format populaire de visualisation de films et autres divertissements visuels avec une vidéo MPEG2 de haute qualité & un son numérique environnant. Permet la fonction multi-langues, multi-sous-titrage et d’autres fonctions avancées. DVD Audio Ce format de stockage audio uniquement double la fidélité de l’effet son par rapport à un CD standard et permet une répetitions des lectures qui dure plus longtemps, l’interdiction de la copie et des mesures anti piratage etc.
Graveur DVD +/- R/RWr DVD-RAM (DVD Random Access Memory) Le format du Forum DVD réinscriptible 100 000 fois. Convient aux sauvegardes et DVR. Référence Pour obtenir plus d’informations relatives aux organisations et à la définition des formats DVD, veuillez vous référer aux sites web suivants: http://www.dvdrw.com http://www.dvdforum.org http://www.licensing.philips.com http://www.disctronics.co.uk http://www.dvdfllc.co.
3100552441 Version 1.