User manual SV12 JN.00000 PN.000000-00-00 00.00.00 VERSION NO.01 Dyson V15 detect Top view of the Dyson V15 detect machine, showing cleaner head, wand, bin and main body.
In the box Your machine will come with one or more of these cleaner heads – not all will be included. Vacuum cleaner with click-in battery Laser Slim Fluffy™ cleaner head A precisely-angled laser makes invisible dust visible on hard floors. High torque cleaner head with anti-tangle comb Dyson DLS™ technology monitors brush bar resistance and adapts power across different floor types. Polycarbonate teeth prevent tangling around the bristles.
o % sh l nol Getting started Location of the Selection button on the screen on the filter end of the machine. Power modes Your machine has three power modes for different tasks. Change power modes quickly using a single button. Eco The screen showing the machine set to Eco mode with a full battery in green to show that this will give the longest battery life of the three modes.
The LCD screen The LCD screen shows your particle count information and performance, including the cleaning mode selected, remaining run time, filter maintenance and blockage information. Eco Auto Med 100% Settings menu Control the settings on your machine using the button. To enter the settings menu, press and hold the button until the menu screen appears. Tap to scroll through the options available. Boost Eco Auto Eco Auto The Selection button on the screen being pressed.
Low run time 4:50 Run time countdown When the battery needs charging, your machine will pulse three times and a low run time icon will appear on the screen. Low run time Auto Low run time When your battery is empty, a red warning icon will appear on the screen. When Particle count and graph is turned on, low run time will be in amber and red when in Boost mode. English Espanol English 4:50 Auto The screen with a batteryEnglish time remaining shown as a number and as a half filled battery.
Charging your machine The charger connected from the power supply using the wall dock. It’s important to fully charge your new machine before using it for the first time, and after every clean. This is because the battery and monitoring system’s algorithm ‘learns’ over time, and fully charging your machine helps it to more accurately calculate and display remaining run time. Connect to charger either directly or in the dock. The blue LEDs on either side of the battery will flash during charging.
Emptying your bin Empty as soon as the dirt reaches the MAX level – don’t overfill. Using your machine when the dirt is above the MAX line may affect the performance and require more frequent filter washing. The MAX mark on the bin of the machine, showing that the dirt should not be filled over the Max mark when the machine is at the angle of normal use. Overfilling your bin could result in inaccurate readings on the particle graph.
Clearing blockages Disconnect your machine from the charger before looking for blockages. Be careful not to touch the trigger and be aware of sharp objects. Leave your machine to cool down before looking for blockages. Don't use your machine when looking for blockages as this could cause injury. If your machine detects a blockage, the motor will pulse and you won’t be able to use your machine until the blockage has been cleared.
Washing your filter Wash your filter at least once a month to maintain optimum suction power. For more information and support for your machine go online: www.dyson.com/support Important: your filter must be completely dry before you put it back into the machine. Your machine could be damaged if used with a damp filter. Twist off your filter Twist your filter anti-clockwise and pull it away from your machine. The filter is located at the rear of your machine.
Washing your Laser Slim Fluffy™ brush bar Your Laser Slim Fluffy™ cleaner head has a washable brush bar. To maintain optimum performance, check and wash your brush bar regularly. Make sure your machine is disconnected from the charger and take care not to touch the trigger. 1 The end cap is located at the side of the cleaner head. Push this upwards to unlock the brush bar. Don't wash the end cap.
Clearing obstructions from your High Torque cleaner head with anti-tangle comb Your High Torque cleaner head with anti-tangle comb doesn't have a washable brush bar. To maintain optimum performance, check your brush bar regularly and clear any obstructions. Make sure your machine is disconnected from the charger and take care not to touch the trigger. Remove your brush bar Don’t put any part of your machine in a dishwasher or use detergents, polishes or air fresheners.
Cleaning your tools Don’t put any part of your machine in a dishwasher or use detergents, polishes or air fresheners. Wipe with a damp, lint-free cloth, without touching the connector end. Make sure your tools are completely dry before using.
Clearing blockages from your Hair screw tool Your Hair screw tool doesn't have a washable brush bar. To maintain optimum performance, check your brush bar regularly and clear any obstructions. Make sure your machine is disconnected from the charger and take care not to touch the trigger. The curved locking lever located on the back of the tool. Remove the cover and brush bar Remove the Hair screw tool from the wand or machine. Push the base plate open.
Looking after your machine To always get the best performance from your machine, it’s important to clean it regularly and check for blockages. Look after your machine If your machine is dusty, wipe with a damp lint-free cloth. Check for blockages in the cleaner head, tools and main body of your machine. Wash your filter regularly and leave to dry completely. Don’t use detergents or polishes to clean your machine.
