Sehr geehrte Kunden, Sie haben sich fir ein Qualitätsprodukt aus dem Hause einkoche -ast GmbH entschieden. Wir bedanken uns dafür und wissen Ihr Vertrauen sehr zu schnitzen. Mit unseren Rohmotoren lassen sich Rollladen einfach und preisgünstig elektromechanisch antreiben. Die Rohrmotoren von einkoche wurden mit einem hohen Anspruch an Qualität und Zuverlässigkeit fair Sie entwickelt und produziert. Sie sind wartungsfrei, langlebig und robust. Unsere Motoren laufen leise und präzise.
| Voraussetzungen fir den Einsatz » Das Motorkabel muss innen liegend im Leerrohr, unter Beachtung der örtlichen Elektrovorschriften, bis zur Abzweigdose versiegt werden. * Verwenden Sie nur Originalbauteile und -zubereite des Herstellers. + Fir den elektrischen Anschluss muss am Einbauort eine Spannungsversorgung von 230 V/50 Hz zur Verfolgung stehen.
Schieben Sie zuerst den Motor mit der Seite des Antriebsadapters in die Wickelwelle. Wichtig! Bei Wickelwellen mit innen liegender Falz muss der Motor ausreichend Freiraum haben Drinstecken Sie danach die Wickelwelt le vollständig auf den Adapter am Motorkopf. Wichtig! Achten Sie darauf, dass der Adapter wehrend der Montage nicht vom Endlagenring am Antriebskopf abrutscht, es kommt sonst zu Fehlfunktionen.
Fair das Schalten der Funktionen sind ausschließlich Baudratenbestimmung dafür geeignete Schalter oder Taster zu verwenden. Ortsfeste Steuereinrichtungen (Schalter, Taster etc.) missen sichtbar angebracht werden Fair die ortsfeste Steuerung kann z.B. ein fair diesen Zweck zugelassener einpoliger Hupenschalter oder -satter fair Alufund Ab-Bewegungen verwendet werden.
Das Überschreiten dieser Zeit oder häufiges Umschalten fixieren zur Erwiderung und der Thermoschutz schaltet den Motor ab. Lassen Sie den Motor in diesem Fall ca. 20 Min. abkriegen. Achtung Bereits nach kurzem Dauerbetrieb (ca. 1 Min.) erhitzt sich der Motor im Bereich des Antriebs auf etwa 50°C und bis zur Abschaltung nach ca. 4 Min. kann sich die Ober flache bis ca. 100°C erhitzen. Lassen Sie den Motor abkriegen, ansonsten besteht beim Berichten des Motormantelrohres Verbrennungsgefahr.
| Contents General safety information .. Assembly information. Assembling the tubular . Assembling the brackets Placing the tubular motor in the winding shaft. Mounting the motor on the Safety information: Connection to an electrical network .. Electrical connection Adjustment of the limit positions. 81 Installation of the roller shutter... . 62 Adjustment oft he upper and lower limit position of motor type ER 13 7. Estrus, Dusting limit postilions 8. Troubleshooting... 9. Maintenance... 10.
Dear Customers, Thank you for choosing a quality product from thicko e-sat Gm. We appreciate your rust. Our tubular motors enable the electromagnetically operation of roller shutter systems easily and cost-effectively. Our fibular motors are developed and produced with a high degree of quality and reliability. Furthermore, our robust tubular motors are maintenance-free and offer a long life span. | Conformity This product fulfills the requirements of the valid European and national guidelines and laws.
[Requirements » The motor cable must be laid and connected to the junction box through the tube, according to local electrical standards. * Only use original components and accessories provided by the manufacturer. » The installation site must have access to a fused electrical connection of 230 VIII Hz at all mes. » In the permanent electrical installation, an approved isolating device must be installed, which safely disconnects each pole with a contact gap of at least 3 mm from the power supply.
Firstly, please pace the motor with the side of the crown adapter in the shaft. Important! The motor needs to have sufficient space when using shafts with inward rabbets. Afterwards press the winding shaft completely onto the adapter on the motors head Important! Make sure that the adapter does not move off of the motors head while assembling, otherwise the adapter will malfunction. [Placing the Idler ball bearing {not included in the scope of delivery) Place the idler info the winding shaft.
Only suitable switches or buttons must be used for switching the functions. Local control devices (switches, buttons etc.) must be installed visibly. For a fixed control location, a licensed element can be used e.g. a single-pole 2-tacker switch for up and down movement. The network cable and the two conductors of the motor are to be connected to the appropriate terminals of the switch Please follow the instructions of the switch.
Exceeding this time or frequent switching can lead to overheating. The thermal overload protection will then automatically switch the motor off. Leave the motor to cool down for approx. 20 minutes. Attention! Even a short period of continuous operation (approx. 1 minute} can lead fo the motor drive reaching temperatures of around 50°C. This can further increase to approx. 100°C in the time the motor powers off (approx.
[10 Technical Data Item no. ER1040-13 ER1060-10 ER1060-20 ER1060-30 ER1060-40 ER1060-50 Motor length without bracket| [mm] | 465 469 469 539 538 539 Motor diameter [mm] Input voltage Heavy] | 230/50 230/50 230/50 230/50 230/50 230/50 Power Ww 121 12 145 191 198 205 Rated torque Max. load [kal Rated rpm [rpm] Current consumption [Al 0,61 0,52 0,69 0,92 0,90 0,98 Power on duration [min] Number of wires Wire cross-section [mm] | 075 0,75 0,75 0,75 0.