Datasheet

ManualsBrandsE+E Elektronik ManualsClimatic SensorsMoisture Meter 180 °C 4 to 20mA

v1.8 / Modification rights reserved

EE300Ex-HT

The EE300Ex humidity / temperature transmitter has been

designed specifically for measurement in explosion hazard

areas. It complies with the classifications for Europe (ATEX),

International (IECEx) and USA / Canada (FM).

Accurate measurement over the full range of 0…100 % RH

and -40…180 °C (-40...356 °F) is also possible in applications

under pressure from 0.01 … 300 bar (4351 psi).

The EE300Ex can be used in flammable gas and dust

applications. The entire transmitter can be placed in a

explosion hazardous area. With the remote sensing probe a

temperature classification up to T6 can be reached.

With a stainless steel enclosure and sensing probe the

EE300Ex is the ideal transmitter for challenging industrial

applications. The 2-part construction facilitates simple installa-

tion and rapid replacement of the measuring section without

time consuming wiring. The well proven E+E humidity sensors

ensure reliable measurement performance and long term

stability.

Based on 2-wire technology, the transmitter can be

barriers. The measured values are available on two 4…20mA

analog outputs. In addition to the measured values for humidity and temperature, the EE300Ex calculates

dew point, frost point, absolute humidity, mixing ratio and other humidity related physical quantities.

When outside of the hazardous measurement area, the setup of the EE300Ex can be easily customized by

using the supplied configuration software. This includes the configuration of the analog outputs and the cali-

bration of the humidity and temperature during service.

Measurement of moisture in oil:

Besides measurement in the air, the EE300Ex can be employed for measurement of both absolute water

content (x) in ppm or relative water activity (aw) in oils.

Typical applications include oil purifiers and online monitoring of lubrication and hydraulic oils on off shore

oil rigs.

The USA and Canada approval is valid for air and gas measurement only.

Humidity/Temperature Transmitter

for Intrinsically Safe Applications

EE300Ex-HT

EE300Ex - wall mounting

EE300Ex - remote sensing probe

EE300Ex-HT

chemical process control

pharmaceutical applications

explosive / hazardous storage rooms

flour mills

moisture in oil measurement

approved for gas and dust

installation in zone 0 / Div. 1

calculation of related physical quantities

stainless steel housing and probe

highest accuracy up to 180°C (356°F)

pressure tight up to 300bar (4351psi)

Typical Applications

Features

Summary of content (6 pages)

PAGE 1
EE300Ex-HT Humidity/Temperature Transmitter for Intrinsically Safe Applications The EE300Ex humidity / temperature transmitter has been designed specifically for measurement in explosion hazard areas. It complies with the classifications for Europe (ATEX), International (IECEx) and USA / Canada (FM). Accurate measurement over the full range of 0…100 % RH and -40…180 °C (-40...356 °F) is also possible in applications under pressure from 0.01 … 300 bar (4351 psi).
PAGE 2
Display Two of the measured or calculated physical quantities can be selected with push buttons on the front cover to be shown on the optional display. EE300Ex version with display is not available for environments with combustible dust, Fibers and Flyings and gases with EPL Ga IIC (Group A&B). T: 33.8°C RH: 45.2% The gray area shows the allowed measurement range for the humidity sensor.
PAGE 3
Technical Data EE300Ex Measuring values Relative humidity 1) Humidity sensor HC1000 1) Measuring range 0...100% RH 2) Accuracy (including hysteresis, non-linearity and repeatability, traceable to international standards, administrated by NIST, PTB, BEV...) -15...40°C (5...104°F) ≤90% RH ± (1.3 + 0.3%*mv) % RH ± 2.3% RH -15...40°C (5...104°F) >90% RH -25...70°C (-13...158°F) ± (1.4 + 1%*mv) % RH -40...180°C (-40...356°F) ± (1.5 + 1.5%*mv) % RH Temperature dependence electronics typ. 0.
PAGE 4
Ex - Classifications Europe (ATEX) Certificate: TPS 13 ATEX 38892 003 X by TÜV SÜD Product Service GmbH Safety factors: Ui = 28V; Ii = 100mA; Pi = 700mW; Ci = 2.2nF; Li ≈ 0mH Ex-Designation: Transmitter without display Transmitter with display Remote sensing probe II 1 G Ex ia IIC T4 Ga II 2 G Ex ia IIC T4 Gb II 1 G Ex ia IIC T6-T1 Ga International (IECEx) / / / II 1 D Ex ia IIIC T80°C Da II 1 G Ex ia IIB T4 Ga II 1 D Ex ia IIIC T80°C...220°C Da Certificate: IECEx FMG 14.
PAGE 5
Ordering Guide EE300Ex-HT EE300Ex-HT6S Model Display Electrical Connection Hardware Configuration Probe - Cable Length Probe Length Zone Feedthrough (probe fitting) Filter Sensor Protection Ex-Certification Measured Value Units Software Configuration Physical Parameters Output 1 Scaling Range Output 1 Physical Parameters Output 2 Scaling Range Output 2 wall mounting remote sensing probe up to 20 bar (300p si) remote sensing probe up to 300 bar (4351 psi) without display with display 1) 2 x M16 c
PAGE 6
Scaling Ranges UW - Relative Humditiy [% RH] 001 0...100 Tx - Temperature / TD - Dew Point Temperature / TF- Frost Point Temperature / TW- Wet Bulb Temperature [°C or °F] 002 -40...60 007 0...60 015 20...120 003 -10...50 008 -30...70 022 -40...80 004 0...50 012 -40...120 024 -20...80 005 0...100 014 -20...100 052 -40...180 083 -40...140 Ex - Water vapour partial pressure [mbar] 001 0...200 002 0...1000 002 0...900 Rx - Mixture ratio [g/kg] 001 0...