User's Manual
Table Of Contents
- RF ENERGY EXPOSURE AWARENESS AND CONTROL INFORMATION, AND OPERATIONAL INSTRUCTIONS FOR FCC OCCUPATIONAL USE REQUIREMENTS
- TABLE OF CONTENTS
- SECTION 1 FEATURES
- SECTION 2 CONTROLS AND DISPLAY
- SECTION 3 GENERAL OPERATION
- SECTION 4 RADIO-WIDE FEATURES
- SECTION 5 CONVENTIONAL MODE FEATURES
- 5.1 Introduction
- 5.2 Monitoring Before Transmitting
- 5.3 Monitor Mode
- 5.4 Busy Channel Lockout
- 5.5 Call Guard Squelch
- 5.6 Penalty Timer
- 5.7 Conversation Timer
- 5.8 Repeater Talk-Around
- 5.9 Displaying Transmit/Receive Frequency
- 5.10 Emergency Alarm and Call
- 5.11 Conventional Mode Scanning
- 5.12 Standard Conventional Calls
- 5.13 DTMF/ANI Signaling
- 5.14 Single Tone Encoder
- 5.15 MDC1200 Compatibility
- 5.16 Clone Mode
- 5.17 Project 25 Mode Features
- 5.18 Keypad Programming
- SECTION 6 SMARTNET/SMARTZONE/P25 TRUNKED FEATURES
- 6.1 Introduction
- 6.2 Analog and Digital Operation
- 6.3 Viewing Unit ID
- 6.4 Standard Group Calls
- 6.5 Private (Unit-To-Unit) Calls
- 6.6 Telephone Calls
- 6.7 Call Alert
- 6.8 Messaging
- 6.9 Sending Status Conditions
- 6.10 Emergency Alarm and Call
- 6.11 Failsoft Operation
- 6.12 SMARTNET/Smartzone/P25 Trunked Scanning Features
- 6.13 Dynamic Regrouping
- 6.14 SmartZone and P25 Trunked Unique Features
- SECTION 7 MISCELLANEOUS
- SECTION 8 DETERMINING AVAILABLE OPTIONS
- SECTION 9 PASSWORD DESCRIPTION
- SECTION 10 SECURE COMMUNICATION (ENCRYPTION)
- INDEX
![](/manual/e-f-johnson/2424130/1-user-s-manual-english/images/img-47.png)
SMARTNET/SMARTZONE/P25 TRUNKED FEATURES
47
6.7.3 INITIATING A PAGE
1. With a SMARTNET/SmartZone or P25 Trunked
channel selected, momentarily press the Call Alert
option switch or select that menu parameter. The
alias of the last ID called is displayed.
2. If required, press the Up/Down switch to display the
desired radio. The alias of each number is
displayed.
3. Press the PTT switch or the F2 key and one of the
following occur:
• If five beeps sound, the system received the page
and the paged radio is on the air and received it.
The page mode is automatically exited.
• If the system received the page but the called
radio is not on the air, a single beep sounds and
“NO ACK” is displayed 6 seconds after the PTT
switch is pressed. Auto exit then occurs.
6.8 MESSAGING
NOTE: This feature is not available with P25 trunked
operation.
The messaging feature allows preprogrammed
messages to be sent to a dispatcher. Up to 16 messages
can be preprogrammed, and they are identified by an
alias. If a Message option switch or menu parameter is
programmed, messages are sent as follows:
1. Momentarily press the Message option switch or
select that menu parameter. The alias of the last
message sent is displayed.
2. If required, press the Up/Down switch to display the
desired message. Then send the message by
pressing the F2 key or momentarily pressing the
PTT switch. One of the following events then
occurs:
• If five beeps sound and “ACK RECVD” is
displayed, the message was received and auto-
matically acknowledged by the system.
• If after five tries the message is not acknowl-
edged, a tone sounds and “NO ACK” is
displayed.
6.9 SENDING STATUS CONDITIONS
The status feature allows you to manually or
automatically send your current status to your
dispatcher. Up to eight status conditions can be prepro-
grammed, and they are identified by an alias. If the
Status option switch or menu parameter is
programmed, status conditions are sent as follows:
1. Momentarily press the Status option switch or select
that menu parameter. The alias of the current status
condition is displayed.
2. To change the current status, press the Up/Down
switch until the desired status is displayed. Then to
send the status, press the F2 (Select) switch or
momentarily press the PTT switch. One of the
following events then occurs:
• If five beeps sound and “ACK RCVD” is
displayed, the status was received and acknowl-
edged by the system.
• If after five tries the message is not acknowl-
edged, a tone sounds and “NO ACK” is
displayed.
6.10 EMERGENCY ALARM AND CALL
6.10.1 INTRODUCTION
Emergency Alarms and Calls are separate func-
tions that can be individually enabled or disabled on
each SMARTNET/SmartZone and P25 Trunked
system. The Emergency option switch (or menu
parameter) is required for these functions. Other emer-
gency features are as follows:
• Emergency Alarms are transmitted on the selected
talk group if emergency calls are disabled, and on
the emergency talk group if emergency calls are
enabled.
• Emergency Call talk group selection priority is as
follows. For example, if a global emergency channel
is not programmed, the emergency talk group of the
selected channel is used and so on.
1. Global (radio wide) emergency channel
2. Emergency group of the selected channel