User Manual
Table Of Contents
- RF ENERGY EXPOSURE AWARENESS AND CONTROL INFORMATION, AND OPERATIONAL INSTRUCTIONS FOR FCC OCCUPATIONAL USE REQUIREMENTS
- TABLE OF CONTENTS
- SECTION 1 FEATURES
- SECTION 2 CONTROLS AND DISPLAY
- SECTION 3 GENERAL OPERATION
- SECTION 4 RADIO-WIDE FEATURES
- SECTION 5 CONVENTIONAL MODE FEATURES
- 5.1 Introduction
- 5.2 Monitoring Before Transmitting
- 5.3 Monitor Mode
- 5.4 Busy Channel Lockout
- 5.5 Call Guard Squelch
- 5.6 Penalty Timer
- 5.7 Conversation Timer
- 5.8 Repeater Talk-Around
- 5.9 Displaying Transmit/Receive Frequency
- 5.10 Emergency Alarm and Call
- 5.11 Conventional Mode Scanning
- 5.12 Standard Conventional Calls
- 5.13 DTMF/ANI Signaling
- 5.14 Single Tone Encoder
- 5.15 MDC1200 Compatibility
- 5.16 Clone Mode
- 5.17 Project 25 Mode Features
- 5.18 Keypad Programming
- SECTION 6 SMARTNET/SMARTZONE/P25 TRUNKED FEATURES
- 6.1 Introduction
- 6.2 Analog and Digital Operation
- 6.3 Viewing Unit ID
- 6.4 Standard Group Calls
- 6.5 Private (Unit-To-Unit) Calls
- 6.6 Telephone Calls
- 6.7 Call Alert
- 6.8 Messaging
- 6.9 Sending Status Conditions
- 6.10 Emergency Alarm and Call
- 6.11 Failsoft Operation
- 6.12 SMARTNET/Smartzone/P25 Trunked Scanning Features
- 6.13 Dynamic Regrouping
- 6.14 SmartZone and P25 Trunked Unique Features
- SECTION 7 MISCELLANEOUS
- SECTION 8 DETERMINING AVAILABLE OPTIONS
- SECTION 9 PASSWORD DESCRIPTION
- SECTION 10 SECURE COMMUNICATION (ENCRYPTION)
- INDEX
53
MISCELLANEOUS
SECTION 7 MISCELLANEOUS
7.1 SUPERVISORY TONES
Single Beep (Alert Tone)
• Power was turned on and a successful power-up
sequence occurred (Section 3.1).
• The time-out timer is about to expire or the penalty
timer has expired (Section 4.3).
• The conversation timer is about to expire (Section
5.7).
• The system received your page but the paged radio
is not on the air (Section 6.7).
• Telephone interconnect is not operational (Section
6.6).
Continuous Tone (Invalid Condition)
• A transmission is being attempted on a conventional
channel programmed as receive-only.
• The transmitter is disabled by the busy channel
lockout feature (Section 5.4).
• The transmitter has been disabled by the time-out
timer feature (Section 4.3).
• The transmitter has been disabled by the conversa-
tion timer (Section 5.7).
• An out-of-range condition exists (SMARTNET/
SmartZone and P25 trunking only).
• A transmission is being attempted before the penalty
timer has expired (Section 5.6).
• Dynamic regrouping has been exited but the
dynamic regrouping channel is still selected
(Section 6.13).
Single Short Medium-Pitch Tone
• A valid key has been pressed.
Single Short Low-Pitch Tone
• An invalid key has been pressed.
Medium Tone (No Acknowledge)
• The paged radio did not acknowledge the page
(Section 6.7).
• The message that was sent has not been acknowl-
edged (Section 6.8).
• The status condition that was sent has not been
acknowledged (Section 6.9).
Five Beeps (Recurring)
• The page was received (Section 6.7).
Two Short Tones
• A private call was received (Section 6.5).
Five Beeps
• The paged radio received the page and acknowl-
edged it (Section 6.7).
• The message that was sent has been received and
acknowledged (Section 6.8).
• The status condition that was sent has been received
and acknowledged (Section 6.9).
Four Beeps
• The emergency alarm condition was acknowledged
(Section 6.10).
• Four low tone beeps indicate call back mode (the
system is no longer busy)
Alternating Tone
• Dynamic regrouping has occurred (Section 6.13).
• Dynamic regrouping has occurred but the
regrouping channel is not selected (Section 6.13).
Busy Signal
• The radio system is busy or a busy condition exists
when making a telephone call.
Three Medium Pitch Tones
• A channel is available after a busy condition
occurred (SMARTNET/SmartZone only).