User Manual
Table Of Contents
- RF ENERGY EXPOSURE AWARENESS AND CONTROL INFORMATION, AND OPERATIONAL INSTRUCTIONS FOR FCC OCCUPATIONAL USE REQUIREMENTS
- TABLE OF CONTENTS
- SECTION 1 FEATURES
- SECTION 2 CONTROLS AND DISPLAY
- SECTION 3 GENERAL OPERATION
- SECTION 4 RADIO-WIDE FEATURES
- SECTION 5 CONVENTIONAL MODE FEATURES
- 5.1 Introduction
- 5.2 Monitoring Before Transmitting
- 5.3 Monitor Mode
- 5.4 Busy Channel Lockout
- 5.5 Call Guard Squelch
- 5.6 Penalty Timer
- 5.7 Conversation Timer
- 5.8 Repeater Talk-Around
- 5.9 Displaying Transmit/Receive Frequency
- 5.10 Emergency Alarm and Call
- 5.11 Conventional Mode Scanning
- 5.12 Standard Conventional Calls
- 5.13 DTMF/ANI Signaling
- 5.14 Single Tone Encoder
- 5.15 MDC1200 Compatibility
- 5.16 Clone Mode
- 5.17 Project 25 Mode Features
- 5.18 Keypad Programming
- SECTION 6 SMARTNET/SMARTZONE/P25 TRUNKED FEATURES
- 6.1 Introduction
- 6.2 Analog and Digital Operation
- 6.3 Viewing Unit ID
- 6.4 Standard Group Calls
- 6.5 Private (Unit-To-Unit) Calls
- 6.6 Telephone Calls
- 6.7 Call Alert
- 6.8 Messaging
- 6.9 Sending Status Conditions
- 6.10 Emergency Alarm and Call
- 6.11 Failsoft Operation
- 6.12 SMARTNET/Smartzone/P25 Trunked Scanning Features
- 6.13 Dynamic Regrouping
- 6.14 SmartZone and P25 Trunked Unique Features
- SECTION 7 MISCELLANEOUS
- SECTION 8 DETERMINING AVAILABLE OPTIONS
- SECTION 9 PASSWORD DESCRIPTION
- SECTION 10 SECURE COMMUNICATION (ENCRYPTION)
- INDEX
MISCELLANEOUS
55
Invald Key - The key pressed by the user was not
valid for the current situation.
Invld Ch - The channel entered by the user in keypad
programming is not valid.
Key Fail - The encryption key required by the current
selected group/channel is not valid.
Kypd Lockd - The keypad lock function is active and
key presses are not accepted in this mode.
Kset Fail - The encryption key set chosen by the user
is not valid.
List Only - Direct entry of a unit ID or phone number
is disabled.
Locked - A selector lock command has been received
and zone and channel changes are not accepted.
Lost Signl - Signal from the infrastructure has been
lost during an interconnect call.
Low Power - The current channel is strapped to low
power and that the user can not select high power at
this time.
Msg Failed - The current channel is strapped to low
power and that the user can not select high power at
this time.
Narrow - The current conventional channel is
programmed as a narrow channel.
No Ack - The radio did not receive an ACK for the
current signaling attempt.
No Edit - The current list is not able to be edited.
No Encrypt - Encryption is not available for the
selected channel.
No List - No list is available for the selected channel.
No Message - No message is programmed for trans-
mission.
No Reply - Radio cloning failed due to no response.
No Service - OTAR service is not available.
No Site - No site with a verified ID is yet on the
dynamic site list.
No Keys - No keys are available for the key select
function.
Out Of Rng - This error indicates no control channel
has been found for trunking operation.
Parms Fail - The checksum of the profile / user
parameters does not match the calculated checksum.
This indicates that there is an error in the parameters
file. This message only occurs if the redundant copy of
the parameters is also corrupt or is unable to be used.
Rekey Fail - This error indicates a failure in a
rekeying process.
Rx Only - The selected channel is Rx only.
Sts Failed - No acknowledgement was received while
sending a status report.
Timeout - A time out has occurred in attempting the
current function.
Too H ot - The mobile has passed the TOO HOT
temperature threshold. Under these conditions the
radio will not allow Tx.
Tx Timeout - The Tx time-out timer has expired and
Tx has been terminated.
VOLTAGE HI - The input voltage to the mobile is
too high.
VOLTAGE LO - The input voltage to the mobile is
too low.
Write Fail -
The radio is unable to write to the
EEPROM.
7.3 SYSTEM OPERATOR PROGRAMMING
As noted several times in this manual, program-
ming determines the availability and specific operation
of many features. This usually refers to the program-
ming performed by the PCConfigure programmer