User's Manual
Table Of Contents
- SAFETY INFORMATION
- TABLE OF CONTENTS
- SECTION 1 GENERAL
- SECTION 2 CONTROLS AND DISPLAY
- SECTION 3 GENERAL OPERATION
- SECTION 4 RADIOWIDE FEATURES
- SECTION 5 CONVENTIONAL FEATURES
- 5.1 Introduction
- 5.2 Monitoring Before Transmitting
- 5.3 Monitor Mode
- 5.4 Busy Channel Lockout
- 5.5 Call Guard Squelch
- 5.6 Penalty Timer
- 5.7 Conversation Timer
- 5.8 Repeater Talk-Around
- 5.9 Displaying Transmit/Receive Frequency
- 5.10 Emergency Alarm and Call
- 5.11 Conventional Mode Scanning
- 5.12 Standard Conventional Calls
- 5.13 DTMF/ANI Signaling
- 5.14 Single Tone Encoder
- 5.15 Project 25 Mode Features
- 5.16 Keypad Programming
- SECTION 6 SMARTNET/SMARTZONE/P25 TRUNKED FEATURES
- 6.1 Introduction
- 6.2 Analog and Digital Operation
- 6.3 Viewing Unit ID
- 6.4 Standard Group Calls
- 6.5 Private (Unit-To-Unit) Calls
- 6.6 Telephone Calls
- 6.7 Call Alert
- 6.8 Messaging
- 6.9 Sending Status Conditions
- 6.10 Emergency Alarm and Call
- 6.11 Failsoft Operation
- 6.12 SMARTNET/SmartZone/P25 Trunked Scanning Features
- 6.13 Dynamic Regrouping
- 6.14 SmartZone and P25 Trunking Unique Features
- SECTION 7 MISCELLANEOUS
- SECTION 8 DETERMINING AVAILABLE OPTIONS
- SECTION 9 5300 MOBILE FIRMWARE VERSIONS
- SECTION 10 PASSWORD DESCRIPTION
- SECTION 11 SECURE COMMUNICATION (ENCRYPTION)
- INDEX
SECURE COMMUNICATION (ENCRYPTION)
64
OTAR Rekey Request - Sends a message which tells
the KMF that the radio is on the air and requests
rekeying. The following status messages are displayed
which indicate the progress of this function. Addi-
tional functions that are available when this is selected
using the 5100 menu mode are described in the next
section.
Rekeying
- A radio-initiated rekeying session is in
process.
No Ack
- No response was received from the KMF
in response to an Identify request before time out
occurred (approximately 30 seconds).
Ack Rcvd
- An acknowledgement was received in
response to an Identify request.
No Service
- A “No Service” reply was received
from the KMF. No rekeying will take place.
Rekey Fail
- Either the rekey command failed or
timed out (after approximately 30 seconds). This
message could indicate that the rekey request
message was not received by the KMF. However,
depending on the KMF configuration and channel
traffic, it is possible that the message was received
and a response is still pending.
Rekeyed!
- The rekey session initiated by the radio
was successful.
Additional Functions Selectable by 5100 Menu:
(To select one a parameter, highlight it and press
F2.)
Rekey
- Performs the same function as the OTAR
Rekey Request option switch described in the
preceding section.
Need KEK
- Sends a request for a new KEK (Key
Encryption Key). Upon receiving this message, the
KMF marks the radio as requiring service. One time
this function may be selected is if the radio dumps it
keys.
Identify
- Sends a message which tells the KMF that
the radio is on the air. Currently, the KMF always
responds with “No Service”, even if the keys are not
up to date. If “No Ack” is displayed, the KMF may
not have received the message (see preceding
section). This function can be used to test communi-
cation without initiating the rekeying that occurs
with the preceding “Rekey” function.
Erase Keys
- Erases all keys in the radio the same as
the Erase Keys option switch described in the
preceding section.