Operating Manual Part 15
Table Of Contents
- Safety Information
- General
- Controls And Display
- General Operation
- Radio Wide Features
- Conventional Features
- 5.1 Monitoring Before Transmitting
- 5.2 Monitor Mode
- 5.3 Busy Channel Lockout
- 5.4 Call Guard Squelch
- 5.5 Penalty Timer
- 5.6 Conversation Timer
- 5.7 Repeater Talk-Around
- 5.8 Displaying Transmit / Receive Frequency
- 5.9 Emergency Alarm and Call
- 5.10 Conventional Mode Scanning
- 5.11 Standard Conventional Calls
- 5.12 DTMF / ANI Signaling
- 5.13 Project 25 Mode Features
- 5.14 Keypad Programming
- 5.15 Text Messaging
- 5.16 Sending Global Positioning System (GPS) Data
- SMARTNET / SmartZone / P25 Trunked Features
- 6.1 Analog and Digital Operation
- 6.2 Viewing Unit ID
- 6.3 Standard Group Calls
- 6.4 Private (Unit-To-Unit) Calls
- 6.5 Telephone Calls
- 6.6 Call Alert
- 6.7 Messaging
- 6.8 Sending Status Conditions
- 6.9 Emergency Alarm and Call
- 6.10 Failsoft Operation
- 6.11 SMARTNET / SmartZone / P25 Trunked Scanning Features
- 6.12 Dynamic Regrouping
- 6.13 SmartZone and P25 Trunking Unique Features
- 6.13.1 Busy Override
- 6.13.2 Site Trunking
- 6.13.3 Determining Current Site and Searching for a New Site
- 6.13.4 Locking / Unlocking a Site
- 6.13.5 Auto Site Search
- 6.13.6 ZoneFail Site Lock
- 6.13.7 P25 Wide Area Scan
- 6.13.8 Normal P25 and SmartZone Control Channel Hunt
- 6.13.9 Talkgroup Steering through System Access Permissions
- 6.13.10 P25 Wide Area Scan
- 6.14 P25 Trunking Unique Features
- Miscellaneous
- Determining Available Options
- Password Description
- Secure Communication (Encryption)
- Service Information
October 2008 5300 ES Series Mobile Radio Operating Manual 4-11
Radio Wide Features
1 While receiving a message on the channel to be deleted, press and hold the SCAN
option switch until a tone sounds (approximately 0.5 second). The channel is then
deleted and scanning of the remaining channels in the scan list resumes.
Note Pressing and holding this switch with scanning OFF may select the scan list. Refer to
Section 5.10.1 for more information.
2 Deleted channels are added back into the scan list if any of the following events occur:
- Scanning is turned OFF and then ON again using the SCAN option switch.
- Radio power is turned OFF and then ON again.
- The scan list is reselected by changing channels (SMARTNET/SmartZone) or using
the SCAN option switch (conventional).
4.13 Scan Lists
Priority and Radio Wide Scan lists can be programmed.
4.13.1 Priority Mode Scan Lists
A scan list is simply the channels that are scanned when scanning is enabled. With all
operating modes, as many priority scan lists as are required can usually be programmed
(up to 255). The only limitation is the available memory. Each list can include up to 256
channels/talk groups. More information follows on selecting and editing priority scan lists.
Note The selected channel is always scanned.
4.13.1.1 Determining Channels in Priority Scan List
Channels in the conventional priority scan lists are determined as follows. Channels in the
SMARTNET/SmartZone/P25 Trunked priority scan lists are indicated only when editing a
list (see “Editing a Priority Scan List”).
1 Enable Priority scanning as described in Section 4.12.1. Also select the scan list if
applicable as described in the following “Selecting a Priority Scan List” description.