Operating Manual Part 15
Table Of Contents
- Safety Information
- General
- Controls And Display
- General Operation
- Radio Wide Features
- Conventional Features
- 5.1 Monitoring Before Transmitting
- 5.2 Monitor Mode
- 5.3 Busy Channel Lockout
- 5.4 Call Guard Squelch
- 5.5 Penalty Timer
- 5.6 Conversation Timer
- 5.7 Repeater Talk-Around
- 5.8 Displaying Transmit / Receive Frequency
- 5.9 Emergency Alarm and Call
- 5.10 Conventional Mode Scanning
- 5.11 Standard Conventional Calls
- 5.12 DTMF / ANI Signaling
- 5.13 Project 25 Mode Features
- 5.14 Keypad Programming
- 5.15 Text Messaging
- 5.16 Sending Global Positioning System (GPS) Data
- SMARTNET / SmartZone / P25 Trunked Features
- 6.1 Analog and Digital Operation
- 6.2 Viewing Unit ID
- 6.3 Standard Group Calls
- 6.4 Private (Unit-To-Unit) Calls
- 6.5 Telephone Calls
- 6.6 Call Alert
- 6.7 Messaging
- 6.8 Sending Status Conditions
- 6.9 Emergency Alarm and Call
- 6.10 Failsoft Operation
- 6.11 SMARTNET / SmartZone / P25 Trunked Scanning Features
- 6.12 Dynamic Regrouping
- 6.13 SmartZone and P25 Trunking Unique Features
- 6.13.1 Busy Override
- 6.13.2 Site Trunking
- 6.13.3 Determining Current Site and Searching for a New Site
- 6.13.4 Locking / Unlocking a Site
- 6.13.5 Auto Site Search
- 6.13.6 ZoneFail Site Lock
- 6.13.7 P25 Wide Area Scan
- 6.13.8 Normal P25 and SmartZone Control Channel Hunt
- 6.13.9 Talkgroup Steering through System Access Permissions
- 6.13.10 P25 Wide Area Scan
- 6.14 P25 Trunking Unique Features
- Miscellaneous
- Determining Available Options
- Password Description
- Secure Communication (Encryption)
- Service Information
October 2008 5300 ES Series Mobile Radio Operating Manual 5-13
Conventional Features
5.11 Standard Conventional Calls
Standard conventional calls can be placed to other radios monitoring the selected channel.
The proper coded Call Guard squelch tone or code or P25 NAC may need to be
transmitted by your radio for them to receive your call (see Sections 5.4 and 5.13.3).
5.11.1 Placing a Standard Conventional Call
To place a standard conventional call, proceed as follows:
1 Turn power ON and set the volume as described in Section 3.1. Select the channel
programmed for the radio you want to call (see Section 3.4.2).
2 Monitor the channel automatically or manually as described in Section 5.1.
3 Press the PTT switch and if the Busy Channel Lockout feature is programmed on the
channel, the transmitter is automatically disabled if the channel is busy (see Section
5.3). Otherwise, busy and out-of-range conditions are not indicated and speaking can
begin after monitoring the channel.
4 Press (and hold) the PTT switch to talk and release it to listen. When the call is
finished, place the microphone back on-hook.
5.11.2 Receiving a Standard Conventional Call
To receive a standard conventional call, proceed as follows:
1 Select or scan the channel programmed for the call you want to receive (refer to Section
5.10 for more scanning information).
2 After the call is received, take the microphone off-hook and press the PTT switch to
talk and release it to listen. If scanning, responses may occur on the priority, selected,
or receive channel as described in Section 5.10.2.
3 When the call is finished, place the microphone back on-hook.
5.12 DTMF / ANI Signaling
DTMF (Dual Tone Multi-Frequency) tones can be generated for ANI (Automatic Number
Identification) and other purposes on conventional analog channels. One of the following
options may be enabled on each channel: