Operating Manual Part 15
Table Of Contents
- Safety Information
- General
- Controls And Display
- General Operation
- Radio Wide Features
- Conventional Features
- 5.1 Monitoring Before Transmitting
- 5.2 Monitor Mode
- 5.3 Busy Channel Lockout
- 5.4 Call Guard Squelch
- 5.5 Penalty Timer
- 5.6 Conversation Timer
- 5.7 Repeater Talk-Around
- 5.8 Displaying Transmit / Receive Frequency
- 5.9 Emergency Alarm and Call
- 5.10 Conventional Mode Scanning
- 5.11 Standard Conventional Calls
- 5.12 DTMF / ANI Signaling
- 5.13 Project 25 Mode Features
- 5.14 Keypad Programming
- 5.15 Text Messaging
- 5.16 Sending Global Positioning System (GPS) Data
- SMARTNET / SmartZone / P25 Trunked Features
- 6.1 Analog and Digital Operation
- 6.2 Viewing Unit ID
- 6.3 Standard Group Calls
- 6.4 Private (Unit-To-Unit) Calls
- 6.5 Telephone Calls
- 6.6 Call Alert
- 6.7 Messaging
- 6.8 Sending Status Conditions
- 6.9 Emergency Alarm and Call
- 6.10 Failsoft Operation
- 6.11 SMARTNET / SmartZone / P25 Trunked Scanning Features
- 6.12 Dynamic Regrouping
- 6.13 SmartZone and P25 Trunking Unique Features
- 6.13.1 Busy Override
- 6.13.2 Site Trunking
- 6.13.3 Determining Current Site and Searching for a New Site
- 6.13.4 Locking / Unlocking a Site
- 6.13.5 Auto Site Search
- 6.13.6 ZoneFail Site Lock
- 6.13.7 P25 Wide Area Scan
- 6.13.8 Normal P25 and SmartZone Control Channel Hunt
- 6.13.9 Talkgroup Steering through System Access Permissions
- 6.13.10 P25 Wide Area Scan
- 6.14 P25 Trunking Unique Features
- Miscellaneous
- Determining Available Options
- Password Description
- Secure Communication (Encryption)
- Service Information
October 2008 5300 ES Series Mobile Radio Operating Manual 5-19
Conventional Features
5.13.7 Call Alert
The Call Alert™ feature allows pages to be sent and received on P25 conventional
channels. The Call Alert Encode and Decode options must be enabled to send or receive
an alert. Operation is similar to SMARTNET/SmartZone and P25 Trunked channels.
To answer a page:
1 When a page is received, five beeps sound and “PAGE RCVD” is displayed. The ID of
the radio paging you is stored as the last ID received.
2 To clear or ignore the page, press any option switch. If the PTT switch is pressed, a
group call is placed on the selected channel.
3 To answer the page as a unit call (see Section 5.13.5), press the CALL (Private/Unit)
option switch (or select the option from the menu). The alias of the radio paging you is
displayed. Press the PTT switch and respond. One of the following conditions then
occur:
- If the radio being called is on the air, ringing is heard until the called party answers or
for 20 seconds, whichever occurs first. If no answer occurs within 20 seconds, a
continuous tone sounds and “NO ANS” is displayed.
- If the radio being called is not on the air, a continuous tone is heard instead of ringing
and “NO ACK” is displayed.
4 When the call is finished or if it could not be completed for some reason, end it by
pressing the Unit Call option switch or the F1 (Exit) key.
To initiate a page:
1 With a P25 conventional channel selected, momentarily press the ALERT (Call Alert)
option switch. The alias of the last ID called is displayed. Or press and hold the switch
to directly enter the ID of the radio you wish to page.
2 If required, rotate the Select switch to display the desired radio. The alias of each
number is displayed.
3 Press the PTT switch and one of the following occur:
• If five beeps sound, the system received the page and the paged radio is on the air and
received it. The page mode is automatically exited.
• If the system received the page but the called radio is not on the air, a single beep
sounds and “NO ACK” is displayed six seconds after the PTT switch is pressed. Auto
exit then occurs.