Operating Manual Part 15
Table Of Contents
- Safety Information
- General
- Controls And Display
- General Operation
- Radio Wide Features
- Conventional Features
- 5.1 Monitoring Before Transmitting
- 5.2 Monitor Mode
- 5.3 Busy Channel Lockout
- 5.4 Call Guard Squelch
- 5.5 Penalty Timer
- 5.6 Conversation Timer
- 5.7 Repeater Talk-Around
- 5.8 Displaying Transmit / Receive Frequency
- 5.9 Emergency Alarm and Call
- 5.10 Conventional Mode Scanning
- 5.11 Standard Conventional Calls
- 5.12 DTMF / ANI Signaling
- 5.13 Project 25 Mode Features
- 5.14 Keypad Programming
- 5.15 Text Messaging
- 5.16 Sending Global Positioning System (GPS) Data
- SMARTNET / SmartZone / P25 Trunked Features
- 6.1 Analog and Digital Operation
- 6.2 Viewing Unit ID
- 6.3 Standard Group Calls
- 6.4 Private (Unit-To-Unit) Calls
- 6.5 Telephone Calls
- 6.6 Call Alert
- 6.7 Messaging
- 6.8 Sending Status Conditions
- 6.9 Emergency Alarm and Call
- 6.10 Failsoft Operation
- 6.11 SMARTNET / SmartZone / P25 Trunked Scanning Features
- 6.12 Dynamic Regrouping
- 6.13 SmartZone and P25 Trunking Unique Features
- 6.13.1 Busy Override
- 6.13.2 Site Trunking
- 6.13.3 Determining Current Site and Searching for a New Site
- 6.13.4 Locking / Unlocking a Site
- 6.13.5 Auto Site Search
- 6.13.6 ZoneFail Site Lock
- 6.13.7 P25 Wide Area Scan
- 6.13.8 Normal P25 and SmartZone Control Channel Hunt
- 6.13.9 Talkgroup Steering through System Access Permissions
- 6.13.10 P25 Wide Area Scan
- 6.14 P25 Trunking Unique Features
- Miscellaneous
- Determining Available Options
- Password Description
- Secure Communication (Encryption)
- Service Information
October 2008 5300 ES Series Mobile Radio Operating Manual 6-7
SMARTNET / SmartZone / P25 Trunked Features
- The call must be answered within 20 seconds or it is automatically terminated.
- If the system is busy when a response is made, “BUSY” is displayed and the busy
tone sounds.
6.5 Telephone Calls
The telephone call feature allows telephone calls to be placed and received over the public
telephone system using your radio. The type of call (secure/clear) is determined by the
mode selected by the Clear/Secure option switch or the menu parameter selected.
Telephone calling is programmed to operate in one of the following modes:
• Disabled (telephone calls not available).
• Answer-only capability.
• List only - Telephone numbers can be selected from a preprogrammed list only (direct
entry as follows is not allowed).
• Unlimited - Telephone numbers can be selected from a list and also dialed directly
entered using the front panel controls or the keypad on the HHC.
6.5.1 Placing a Telephone Call
To recall from a list:
1 With a SMARTNET/SmartZone/P25 channel selected, momentarily press the Phone
option switch (or select the menu parameter). The alias of the last called telephone
number is displayed.
2 If required, rotate the Select switch to display the desired number. The alias of each
number is displayed.
3 Press and then release the PTT switch and “DIALING” is displayed. Refer to the
bulleted list following Step 3 in the next section for events that may then occur.
To make a direct entry using DTMF keypad:
1 Select the menu parameter or press and hold the PHONE option switch until a tone
sounds (approximately one second). The alias of the last called telephone number is
displayed if it is in the phone number list. Otherwise, the last ten digits of the last called
telephone number are displayed. The phone call mode is indicated by in the
display.