Operating Manual Part 15
Table Of Contents
- Safety Information
- General
- Controls And Display
- General Operation
- Radio Wide Features
- Conventional Features
- 5.1 Monitoring Before Transmitting
- 5.2 Monitor Mode
- 5.3 Busy Channel Lockout
- 5.4 Call Guard Squelch
- 5.5 Penalty Timer
- 5.6 Conversation Timer
- 5.7 Repeater Talk-Around
- 5.8 Displaying Transmit / Receive Frequency
- 5.9 Emergency Alarm and Call
- 5.10 Conventional Mode Scanning
- 5.11 Standard Conventional Calls
- 5.12 DTMF / ANI Signaling
- 5.13 Project 25 Mode Features
- 5.14 Keypad Programming
- 5.15 Text Messaging
- 5.16 Sending Global Positioning System (GPS) Data
- SMARTNET / SmartZone / P25 Trunked Features
- 6.1 Analog and Digital Operation
- 6.2 Viewing Unit ID
- 6.3 Standard Group Calls
- 6.4 Private (Unit-To-Unit) Calls
- 6.5 Telephone Calls
- 6.6 Call Alert
- 6.7 Messaging
- 6.8 Sending Status Conditions
- 6.9 Emergency Alarm and Call
- 6.10 Failsoft Operation
- 6.11 SMARTNET / SmartZone / P25 Trunked Scanning Features
- 6.12 Dynamic Regrouping
- 6.13 SmartZone and P25 Trunking Unique Features
- 6.13.1 Busy Override
- 6.13.2 Site Trunking
- 6.13.3 Determining Current Site and Searching for a New Site
- 6.13.4 Locking / Unlocking a Site
- 6.13.5 Auto Site Search
- 6.13.6 ZoneFail Site Lock
- 6.13.7 P25 Wide Area Scan
- 6.13.8 Normal P25 and SmartZone Control Channel Hunt
- 6.13.9 Talkgroup Steering through System Access Permissions
- 6.13.10 P25 Wide Area Scan
- 6.14 P25 Trunking Unique Features
- Miscellaneous
- Determining Available Options
- Password Description
- Secure Communication (Encryption)
- Service Information
6-8 5300 ES Series Mobile Radio Operating Manual October 2008
SMARTNET / SmartZone / P25 Trunked Features
2 If using the front panel controls, enter the telephone number by rotating and pressing
the Select switch. A single beep sounds when the switch is pressed (if that option is
selected). The 0-9, the
*, #, and P (pause) characters can be entered (# is displayed as a
“+”). Numbers up to sixteen digits (including pauses) can be entered, and the number
scrolls to the left in the display so that the ten right-most digits are always displayed.
With the HHC, enter the number using the DTMF keypad (a pause indicated by “P” is
entered by
* #).
3 Press and hold the PTT switch and dial the number using the keypad on the HHC.
“DIALING” is displayed. Events that may occur are as follows:
- If the access is successful, a dial tone sounds and the dialed number is displayed and
sent. Either ringing or a busy signal is then heard as with a standard telephone call.
When the called party answers, press the PTT switch to talk and release it to listen
(since the radio operates half-duplex, it is not possible to talk and listen at the same
time).
Each time the PTT switch is released, a go-ahead tone is sent to the landside party to
indicate when they can respond. To dial a number after the connection is made, press
the PTT switch and dial the number using the keypad on the HHC.
Ο If the selected telephone number is not valid, “INVALID” is displayed and an
alert tone sounds. Select a valid number.
Ο If the system is busy, “BUSY” is displayed and the busy tone sounds. The call
automatically proceeds when the system becomes available.
Ο If you are out-of-range or the radio cannot be accessed for some reason, “NO
PHONE” is displayed and an alert tone sounds.
Ο If the interconnect call you are making or the selected secure mode is not
authorized, “REJECT” is displayed and an alert tone sounds.
Ο If your radio does not have the proper encryption key, “KEYFAIL” is displayed
and the call must be made in the clear mode by pressing the Clear/Secure option
key (if strapped to switchable). Otherwise, load the correct key.
4 When the telephone call is finished or it could not be completed for some reason, end it
by pressing the Phone option switch and placing the microphone back on-hook.
6.5.2 Receiving A Telephone Call
To receive a telephone call:
1 When a telephone call is received, “ringing” similar to a standard telephone is heard
and “PHONE” is displayed.
2 To answer the call, select the menu parameter or press the Phone option switch. Press
the PTT switch to talk and release it to listen (since the radio operates half duplex, it is
not possible to talk and listen at the same time).