User Manual

EN
F-14 Tomcat Twin 40mm EDF
4
Transmitter Setup
IMPORTANT: Transmitter features, functions and settings not listed in the
transmitter setup table should remain at the default settings. These transmitter
tables show the basic steps needed to complete setup. For more detailed
transmitter setup information please refer to your transmitter’s manual.
We recommend using the transmitter setup provided. When using the
recommended setup, these are the details of the control inputs;
• The GEAR Channel (Ch 5, default switch A) selects SAFE/AS3X mode.
• The Aux 1 Channel (Ch 6, default switch D) controls the wing sweep
mechanism. The wing sweep mechanism is not proportional, it uses three pre-
determined positions. *
• Switch C is congured for elevator dual rates.
• Switch F is congured for aileron dual rates.
• Switch H is congured for throttle cut.
• The rudder stick controls nose wheel steering, there are no rudders for ight
controls.
* When the aircraft is powered ON the wing sweep (Aux1) switch has to be in the
same position as the wings before the wing sweep will function. The wings will not
move until the wing position and switch position align. If they are both in the same
position when powered ON they will move together from the start.
Trim
Our recommended setup uses trims tied to ight modes. With both trims and wing
sweep tied to ight modes (Switch D), you can independently trim the aileron and
elevator for each wing sweep position. We recommended this conguration for this
F-14 aircraft to account for trim changes which may occur in different wing sweep
positions.
Dual Rates
Attempt your first flights in low rate. For landings, use high rate elevator.
NOTICE: To ensure AS3X technology functions properly, do not lower rate values
below 50%.
NOTICE: If oscillation occurs at high speed, refer to the Troubleshooting Guide
for more information.
Exponential
After rst ights, adjust expo in your transmitter to suit your ying style.
Telemetry Setup
See the Telemetry Setup table after binding. In order for the ESC and battery
information to auto-populate in your transmitter’s telemetry menu, you must begin
telemetry setup with the aircraft bound and connected.
DX Series Transmitter Setup
1. Power ON your transmitter, click on scroll wheel, roll to System Setup and
click the scroll wheel. Choose yes.
2. Go to Model Select and choose <Add New Model> at the bottom of the list.
The system asks if you want to create a new model, select Create
3. Set Model Type: Select Airplane Model Type by choosing the airplane.
The system asks you to conrm model type, data will be reset. Select YES
4. Set Model Name: Input a name for your model le
5. Set F-Mode Setup (Flight Mode); Switch 1: Switch D
6. Set Trim Setup;
Aileron: 5 F Mode
Elevator: 5 F Mode
7. Select <Main Screen>, Click the scroll wheel to enter the Function List
8. Set D/R (Dual Rate) and Expo; Aileron
Set Switch: Switch F
Set High Rates: 100%, Expo 10% - Low Rates: 70%, Expo 5%
9. Set D/R (Dual Rate) and Expo; Elevator
Set Switch: SWITCH C
High Rates: 100%, Expo 10% - Low Rates 70%, Expo 5%
10. Set Throttle Cut; Switch: Switch H, Position: -100%
iX Series Transmitter Setup
1. Power ON your transmitter and begin once the Spektrtum Airware app is open.
Select the orange pen icon in the upper left corner of the screen, the system
asks for permission to Turn Off RF, select PROCEED
2. Select the three dots in the upper right corner of the screen,
select Add a New Model
3. Select Model Option, choose DEFAULT, select Airplane.
The system asks if you want to create a new acro model, select Create
4. Select the last model on the list, named Acro.
Tap on the word Acro and rename the le to a name of your choice
5. Tap and hold the back arrow icon in the upper left corner of the screen to
return to the main screen
6. Go to the Model Setup tab
7. Go to Flight Mode Setup; The system asks if you want to Turn Off RF,
select PROCEED; set Switch 1: Switch D
8. Set Trim Setup;
Aileron: 5 F Mode
Elevator: 5 F Mode
9. Exit Model Setup, Go to the Model Adjust menu
10. Set Dual Rates and Expo; Select Aileron
Set Switch: Switch F
Set High Rates: 100%, Expo 10% - Low Rates: 70%, Expo 5%
11. Set Dual Rates and Expo; Select Elevator
Set Switch: SWITCH C
High Rates: 100%, Expo 10% - Low Rates 70%, Expo 5%
12. Set Throttle Cut; Switch: Switch H, Position: -100%
NX Series Transmitter Setup
1. Power ON your transmitter, click on scroll wheel, roll to System Setup and
click the scroll wheel. Choose yes.
2. Go to Model Select and choose <Add New Model> near the bottom of the
list. Select Airplane Model Type by choosing the airplane, select Create
3. Set Model Name: Input a name for your model le
4. Set F-Mode Setup (Flight Mode); Switch 1: Switch D
5. Set Trim Setup;
Aileron : 5 F Mode
Elevator: 5 F Mode
6. Select <Main Screen>, Click the scroll wheel to enter the Function List
7. Set D/R (Dual Rate) and Expo; Aileron
Set Switch: Switch F
Set High Rates: 100%, Expo 10% - Low Rates: 70%, Expo 5%
8. Set D/R (Dual Rate) and Expo; Elevator
Set Switch: SWITCH C
High Rates: 100%, Expo 10% - Low Rates 70%, Expo 5%
9. Set Throttle Cut; Switch: Switch H, Position: -100%
Videos
Use this QR Code to see videos that will
to help you get the most out of your F-14
Tomcat setup and ying experience.