User Manual

EN
19
0 1
0 1
Left Flap (Channel 6)
Right Flap (Channel 5)
With the basic transmitter setup, the ailerons and aps will operate separately. For
increased aileron authority, the AR637T receiver included in the BNF version may
be congured so the aps can operate as both aps and ailerons.
Servo Plug Order Change
1. Remove the Y-harness plugged into the Ch-6 port on the AR637T, and unplug
the servo leads from the Y-harness.
2. Insert the two ap servo leads into the receiver ports; RIGHT ap into Ch-5
and LEFT ap into Ch-6. We recommend labeling the wires to help identify the
correct ports when mounting the wing.
CAUTION: Connecting servos to the wrong port on the receiver could
cause a crash.
IMPORTANT: A 7-channel or higher transmitter is required for the advanced
BNF receiver setup plus the ability to select between AS3X and SAFE with SAFE
Select. If using a 6 channel transmitter with the advanced receiver setup a
selectable channel for the safe select is not available.
With the following advanced Transmitter Setup, the Full span aileron feature will be
assigned to switch A.
Optional BNF advanced receiver setup
†
Some of the terminology and function locations used in the iX12, iX20 programming may
be slightly different than other Spektrum AirWare™ radios. The names given in parenthesis
correspond to the iX12, iX20 programming terminology. Consult your transmitter manual
for specic information about programming your transmitter.
* Flap programming values may vary slightly. For your initial ights use the recommended
ap travel settings provided in the Flaps section and adjust the ap travel to your
preference on subsequent ights.
#
TRAVEL, SUBTRIM and ABSOLUTE TRAVEL varies slightly per aircraft and will need to be
ned tuned for your specic aircraft.
• ABSOLUTE TRAVEL in SERVO SETUP is set to limit your ap servos from over travel.
AR637T advanced receiver setup port assignments
1 = Throttle
2 = Y-harness: Ailerons
3 = Elevator
4 = Rudder
5 = Right ap
6 = Left ap
Advanced Transmitter Setup
Start all transmitter programming with a blank ACRO model (perform a model
reset), then name the model.
Set Aileron, Elevator and Rudder Dual
Rates to:
HIGH 100%
LOW 70%
Expo
HIGH 10%
LOW 5%
Set Throttle Cut to
Select desired switch to assigned value.
(-130% is default)
Advanced Transmitter Setup
DX6e,
DX6G2
DX7G2,
DX8G2,
DX8e
DX9,
DX18,
DX20,
iX12
iX20
NX6
NX8
NX10
1. Go to the System Setup / Model Setup
2. Set MODEL TYPE: AIRPLANE
3. Set Model Setup, Aircraft Type:
WING: 1 AIL 1 FLAP
4. Set Channel Assign:
Channel Input Cong: Gear > INH
Return to main menu.
5. Go to the Functions List / Model Adjust
6. Set FLAP SYSTEM:
SELECT SWITCH D:
FLAP* ELEVATOR
POS 0: 0%
POS 1: -40% 6%
POS 2: -100% 15%
SPEED 2.0
7. Set MIXING: P-MIX 1
Select: NORMAL
Set Flap > Gear to read FLP > GER
RATE: -100%
#
-100%
#
OFFSET: 0%
Switch: ON
8. Set MIXING: P-MIX 2
Select:NORMAL
Set Aileron > Gear to read AIL > GER
RATE: +100%
#
+100%
#
OFFSET: 0%
TRIM: INH
Switch: A
9. Set MIXING: P-MIX 3
Select: NORMAL
Set Aileron > Flap to read AIL > FLP
RATE: +100%
#
+100%
#
OFFSET: 0%
TRIM: INH
Switch: A
10. Servo Setup:
Reversing: Gear
Travel: Gear: L 100
#
Flap: Down 100
#
R (-)140
#
Up (-)140
#
Absolute Travel: (Not available on 6 and 6e)
Move switch”A” to ON.
Gear: R 1
#
Flap: Up 1
#
L 1760
#
Down 1760
#
CAUTION: It is necessary to set ABSOLUTE TRAVEL limits. The use
of ap and full span ailerons could cause servo over travel.
REMOVE
FACTORY SET-UP
ADVANCED AILERON / FLAP SET-UP
Left Flap servo
Right Flap servo
Aileron servos