User Manual

EN
19
DX8e, DX8 (Gen2), DX9, DX18, DX20, iX12 and iX20
TIP: It is possible to enable or disable the four servo aileron mix by assigning
a switch to the P-Mix instead of setting the switch to ON during setup in steps
8 and 9.
TIP: If you want to use SAFE select with the Advanced model setup, you can
assign a switch to any channel 7-9 for SAFE select. Even though the AR637TA
only has 6 servo ports, it can use up to channel 9 to key SAFE Select.
Advanced Transmitter Setup
Start all transmitter programming with a blank ACRO model (perform a model reset),
then name the model.
Set Dual Rates to
HIGH 100%
LOW 70%
Set Servo Travel to 100%
Set Throttle Cut to -100%
DX6e
DX6G2
1. Go to the SYSTEM SETUP
2. Set MODEL TYPE: AIRPLANE
3. Set AIRCRAFT TYPE:
WING: 1 AIL 1 FLAP
4. Go to the Channel Assign
Channel Input Con g: GEAR (channel 5): INH
5. Optional: Select a switch for channel 7 in Channel Assign if you wish to use
the reversing feature of the Avian Smart ESC
6. Set FLAP SYSTEM:
SELECT SWITCH D:
POS 0: 0% FLAP*
POS 1: 50% FLAP* 14% Elevator
POS 2: 100% FLAP* 20% Elevator
SPEED 2.0
7. Go to the FUNCTION LIST
8. Set MIXING: P-MIX 1
Select; NORMAL
Set INH > INH to read FL > GEAR
RATE: 100% 0%
OFFSET: 0%
TRIM: INH
Switch: ON
9. Set MIXING: P-MIX 2**
Select; NORMAL
Set INH > INH to read AIL > GEAR
RATE: -100% -100%
OFFSET: 0%
TRIM: INH
Switch: ON
10. Set MIXING: P-MIX 3**
Select; NORMAL
Set INH > INH to read AIL > FL
RATE: 100% 100%
OFFSET: 0%
TRIM: INH
Switch: ON
†
Some of the terminology and function locations used in the iX12 and iX20
programming may be slightly different than other Spektrum AirWare™ radios. The
names given in parenthesis correspond to the and iX20 programming terminology.
Consult your transmitter manual for speci c information about programming your
transmitter.
* Flap programming values may vary slightly. For your initial  ights use the
recommended  ap travel settings provided in the Flaps section and adjust the  ap
travel to your preference on subsequent  ights.
** Adjust the percentages in P-Mix 2 and 3 to match the  ap travel to aileron travel at
full alieron right and left.
Advanced Transmitter Setup
Start all transmitter programming with a blank ACRO model (perform a model reset),
then name the model.
Set Dual Rates to
HIGH 100%
LOW 70%
Set Servo Travel to 100%
Set Throttle Cut to -100%
DX8e
DX8
(Gen2)
DX9
DX18
DX20
iX12
iX20
1. Go to the SYSTEM SETUP (Model Setup)
†
2. Set MODEL TYPE: AIRPLANE
3. Go to CHANNEL ASSIGN:
CHANNEL INPUT CONFIG
AUX2 Switch A
4. Set AIRCRAFT TYPE (Model Setup, Aircraft Type)
†
:
WING: 1 AIL 1 FLAP
5. Go to the SYSTEM SETUP
Digital Switch Setup: Switch A
Pos 0: -100
Pos 1: -100 (NO MOTOR REVERSING)
Pos 1: 100 (MOTOR REVERSING)
6. Go to the Channel Assign
SELECT GEAR: INH
7. Optional: Select a switch for channel 7 in Channel Assign if you wish to use
the reversing feature of the Avian Smart ESC
8. Go to the FUNCTION LIST (Model Adjust)
†
9. Set FLAP SYSTEM:
SELECT SWITCH D:
POS 0: 0% FLAP*
POS 1: 50% FLAP* 14% Elevator
POS 2: 100% FLAP* 20% Elevator
SPEED 2.0
10. Set MIXING: P-MIX 1
Select; NORMAL
Set INH > INH to read Normal FL > GEAR
RATE: 100% 0%
OFFSET: 0%
TRIM: INH
Switch: ON
11. Set MIXING: P-MIX 2**
Select; NORMAL
Set INH > INH to read Normal AIL > GEAR
RATE: -100% -100%
OFFSET: 0%
TRIM: INH
Switch: ON (for constant) or select switch for activation
4-aileron mode ON/OFF.
12. Set MIXING: P-MIX 3**
Select; NORMAL
Set INH > INH to read Normal AIL > FL
RATE: 100% 100%
OFFSET: 0%
TRIM: INH
Switch: ON (for constant) or select the same switch as
choosen for P-MIX 2 for activation 4-aileron mode ON/OFF.