Night Radian FT 2.
EN NOTICE All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit www.horizonhobby.com and click on the support tab for this product.
EN Box Contents Quick Start Information Blank (Acro) Model Servo Reversing: Transmitter Rudder: Normal Setup Elevator: Normal Aileron: Normal DO NOT Reverse Throttle Dual Rates: 100% / 70% Dual Rates Ele Rud Center of Gravity (CG) Hi Rate Low Rate =12mm =12mm =35mm =35mm =8mm =8mm =25mm =25mm 2 1/2 inches (63mm) back from leading edge at the root.
EN SAFE® Select Technology (BNF Basic) The evolutionary SAFE® Select technology can offer an extra level of protection so you can perform the first flight with confidence. No complex transmitter programming is required. Just follow the simple bind process to make the SAFE Select system active. When activated, bank and pitch limitations keep you from over-controlling and automatic self-leveling makes recovery from risky or confusing attitudes as simple as releasing the sticks.
EN Model Assembly Tail Installation 2 1. Slide the horizontal stabilizer (A) into the slot of the fuselage. 2. Center the horizontal stabilizer and then secure into place with the 4 included pieces of tape (B). 3. Connect the LED connector on the bottom of the horizontal stabilizer. 4. Connect the clevis to the elevator control horn (C) as shown. 1 A B Connecting a Clevis • Pull the tube from the clevis to the linkage.
EN Model Assembly Continued Wing Installation 1. Slide the wing tube (A) into the fuselage. 2. Install the left and right wing over the wing tube. 3. Guide the LED connectors (B) from both wings into the fuse and toward the bottom hatch. 4. Seat the wings in the slot of the fuselage. Be careful not to pinch any wires. 5. Secure the wings to the fuselage using the included 2 screws (C) as shown. 6. Connect the LED connectors to the connector block as shown.
EN Transmitter and Receiver Binding / Switching ON and OFF SAFE Select This product requires an approved Spektrum™ DSM2®/DSMX® compatible Switching transmitter. Visit www.bindnfly.com for a complete list of approved transmitters. The aircraft has an optional SAFE Select feature, which can be switched ON or OFF easily by binding in a specific manner as described below.
EN SAFE® Select Switch Designation SAFE® Select technology can be easily assigned to any open switch (2 or 3 position) on your transmitter. With this new feature, you now have the flexibility to enable or disable the technology while in flight. Mode 1 and 2 Transmitters IMPORTANT: Before assigning your desired switch, ensure that the travel for that channel is set at 100% in both directions. Assigning a switch Bind the aircraft correctly to activate SAFE Select.
EN Battery Installation and ESC Arming 1 Battery Selection ® We recommend the E-flite 1350mAh 11.1V 30C Li-Po Battery (EFLB13503S30). Refer to the Optional Parts List for other recommended batteries. If using a battery other than those listed, the battery should be within the range of capacity, dimensions and weight of the E-flite Li-Po battery packs to fit in the fuselage. Be sure the model balances at the recommended CG. 1. Lower the throttle and throttle trim to the lowest settings.
EN Center of Gravity (CG) The CG location is measured from the leading edge of the wing at the root. This CG location has been determined with the recommended Li-Po battery (EFLB13003S20) installed all the way forward in the battery compartment. 2-1/2 inches (63mm) back from the leading edge at the root. AS3X Control Direction Test This test ensures that the AS3X® control system is functioning properly. Assemble the aircraft and bind your transmitter to the receiver before performing this test.
EN In Flight Trimming During your first flight, trim the aircraft for level flight at 3/4 throttle with flaps and gear up. Make small trim adjustments with your transmitter’s trim switches to straighten the aircraft’s flight path. 3 Seconds After adjusting trim, do not touch the control sticks for 3 seconds. This allows the receiver to learn the correct settings to optimize AS3X performance. Failure to do so could affect flight performance.
EN Post Flight 1 Disconnect the flight battery from the ESC (Required for Safety and battery life). 5 Repair or replace all damaged parts. 2 Power OFF the transmitter. 6 Store the flight battery apart from the aircraft and monitor the battery charge. 3 Remove the flight battery from the aircraft. 7 4 Recharge the flight battery. Make note of the flight conditions and flight plan results, planning for future flights.
EN Troubleshooting Guide Problem Aircraft will not respond to throttle but responds to other controls Extra propeller noise or extra vibration Reduced flight time or aircraft underpowered Aircraft will not Bind (during binding) to transmitter Aircraft will not connect (after binding) to transmitter Possible Cause Throttle not at idle and/or throttle trim too high Reset controls with throttle stick and throttle trim at lowest setting Throttle servo travel is lower than 100% Make sure throttle servo
EN AMA National Model Aircraft Safety Code Effective January 1, 2014 A. GENERAL A model aircraft is a non-human-carrying aircraft capable of sustained flight in the atmosphere. It may not exceed limitations of this code and is intended exclusively for sport, recreation, education and/or competition. All model flights must be conducted in accordance with this safety code and any additional rules specific to the flying site. 1. Model aircraft will not be flown: (a) In a careless or reckless manner.
EN Limited Warranty What this Warranty Covers Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the product purchased (the “Product”) will be free from defects in materials and workmanship at the date of purchase.
EN Contact Information Country of Purchase United States of America Horizon Hobby Horizon Service Center (Repairs and Repair Requests) Horizon Product Support (Product Technical Assistance) Sales European Union Contact Information servicecenter.horizonhobby.com/ RequestForm/ productsupport@horizonhobby.com 877-504-0233 websales@horizonhobby.com 800-338-4639 Horizon Technischer Service service@horizonhobby.
IT Replacement Parts • Ersatzteile • Pièces de rechange • Pezzi di ricambio Part # | Nummer Numéro | Codice Description Beschreibung Description Descrizione EPKZ1017 Propeller Blades PKZ1018 Prop Adapter & Spinner Set Propeller: Radian Luftschraubenmitnehmer und Spinner: Radian Set adattatore elica & ogiva: Radian PKZ1060 Mini Servo (3W) with Arms, Short Lead Radian - Pales Radian - Set adaptateur d’hélice & cône Mini Servo (3 fils) avec Palonniers, câble court PKZ4121 ControlHorns w/Hardwar
IT Recommended Receivers•Empfohlene Empfänger Récepteurs Recommandés•Ricevitori Raccomandati PNP Only • Nur PNP • PNP Uniquement • Solo PNP Part # | Nummer Numéro | Codice SPMAR610 SPMAR6600T SPMAR6270T SPMAR8010T SPMAR9030T SPMAR636 SPMAR7350 SPMAR9350 SPMA9574 Description AR610 6-Channel Coated Air Receiver Telemetry Equipped Receivers AR6600T 6-Channel Air Integrated Telemetry Receiver AR6270T 6-Channel Carbon Fuse Integrated Telemetry Receiver AR8010T 8-Channel Air Integrated Telemetry Receiver
Night Radian® FT © 2018 Horizon Hobby, LLC. E-flite, DSM, DSM2, DSMX, the DSMX logo, Bind-N-Fly, Z-Foam, ModelMatch, EC3, Celectra and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, LLC. The Spektrum trademark is used with permission of Bachmann Industries, Inc. Futaba is a registered trademark of Futaba Denshi Kogyo Kabushiki Kaisha Corporation of Japan. All other trademarks, service marks and logos are property of their respective owners. US 8,672,726. http://www.
