User Manual

EN
31
Deactivating GPS in the Air
If for any reason you wish to deactivate the GPS system while the aircraft
is airborne, such as if the GPS system is not calibrated correctly or is not
responding as expected, follow the directions below:
1. Press and hold the HP/AL (bind) button and cycle the fl ight mode
switch fully 3 times. The rudder will wag, indicating the GPS system is
deactivated.
2. Maintain control of the aircraft and return to the runway to land manually.
To reactivate the GPS system, power cycle the aircraft.
IMPORTANT: When the GPS system is deactivated, the aircraft’s Holding
Pattern, AutoLand and Virtual Fence modes will not function.
Deactivating GPS on the Ground
WARNING: Do not perform this or any other equipment test with
the propeller installed on the aircraft. Serious injury or property
damage could result from the motor starting inadvertently.
The GPS system is activated from the factory. If for any reason you wish
to deactivate the GPS system, such as to perform a control direction test
indoors or to simply enjoy the aircraft without GPS features, follow the
directions below:
1. Ensure that your transmitter is bound to the aircraft. If necessary, refer to
the Transmitter and Receiver Binding section.
2. Power on the transmitter.
3. Power on the aircraft. After the aircraft fi nds the RF signal, the elevator
will start to move up and down slowly, indicating the GPS system is
searching for satellites.
4. Press and hold the HP/AL (bind) button and cycle the fl ight mode switch
fully 3 times. The elevator will stop moving and the rudder will wag,
indicating the GPS system is deactivated.
To reactivate the GPS system, power cycle the aircraft.
IMPORTANT: When the GPS system is deactivated, the aircraft’s Holding
Pattern, AutoLand and Virtual Fence modes will not function.
IMPORTANT: When GPS is deactived from transmitter, LED will fl ash red
slowly. No other LED indicators will function.
To have LED indicators, unplug GPS from fl ight controller.
Deactivating GPS
Troubleshooting Guide (SAFE + GPS Upgrade)
Problem Possible Cause Solution
Aircraft will not respond to throttle but
responds to other controls
AutoLand was not deactivated after landing
Deactivate AutoLand by pressing the AL/HP button or changing  ight
modes and lower throttle
Home location has not been set Set the home location
Direction of Air eld fence has not been set. Use aileron command to set the fence location.
Ailerons go up aircraft will not bind to
transmitter (during binding)
Transmitter too near aircraft during binding process
Power off transmitter, move transmitter a larger distance from aircraft,
disconnect and reconnect  ight battery to aircraft and follow binding
instructions
Bind switch or button not held long enough during bind process Power off transmitter and repeat bind process
Aircraft or transmitter is too close to large metal object, wireless source or
another transmitter
Move aircraft and transmitter to another location and attempt
binding again
Aircraft was not placed upright
Place aircraft upright after powering up
Ailerons go up and aircraft will not
respond to transmitter (after binding)
Less than a 90-second wait between  rst powering on transmitter
and connecting  ight battery to aircraft
Leaving transmitter on, disconnect and reconnect  ight battery
to aircraft
Aircraft was not upright, level or motionless
Leaving transmitter on, disconnect and reconnect  ight
battery to aircraft assuring that the aircraft is upright, level and
motionless
Aircraft cannot acquire a GPS signal
Turn off GPS
Move to an outdoor location away from metal or concrete and
try again
Aux1 (CH 6) reversed Reverse Aux1
Aircraft will not enter compass calibration Aircraft cannot acquire a GPS signal
Move to an outdoor location away from metal or concrete and
try again
Motor does not respond after landing
Over Current Protection (OCP) stops the motor when the transmitter
throttle is set high and the propeller cannot turn
Fully lower throttle and throttle trim to arm ESC
AutoLand has not been deactivated Press and release HP/AL button to deactivate AutoLand feature
Motor pulses but battery is fully charged,
not an LVC motor pulse
Lost GPS Signal
Turn off the GPS functions
Try  ying at a different location