User Manual

EN
Lights
Bind Port
Right Flap
Left Flap
Ailerons
15
With the basic transmitter setup, the ailerons and flaps will operate separately.
For increased aileron authority, the AR631 receiver included in the BNF version
may be configured so the flaps can operate as both flaps and ailerons.
Servo Plug Order Change
1. Remove the Y-harness plugged into the Ch-6 port on the AR631.
2. Insert two servo extensions (EFLREX9L) into the receiver ports; one in Ch-5
and one in Ch-6.
3. The left flap plugs into the Ch-5 extension. The right flap plugs into the
Ch-6 extension. We recommend labeling the wires to help identify the
correct ports when mounting the wing.
4. Insert the Y-harness into the BIND port. The lights plug into one side of the
Y-harness, and the other side serves as a BIND port.
CAUTION: Connecting servos to the wrong port on the receiver could
cause a crash.
IMPORTANT: A 7-channel or higher transmitter is required for the advanced BNF
receiver setup plus the ability to select between AS3X and SAFE with SAFE Select. If
using a 6 channel transmitter for the advanced receiver setup, only AS3X is available.
Advanced Transmitter Setup
Start all transmitter programming with a blank ACRO model (perform a model
reset), then name the model.
Set Dual Rates to
HIGH 100%
LOW 70%
Set Servo Travel to 100%
Set Throttle Cut to -130%
DX6e
DX6G2
1. Go to the SYSTEM SETUP
2. Set MODEL TYPE: AIRPLANE
3. Set AIRCRAFT TYPE:
WING: 1 AIL 1 FLAP
4. Set CHANNEL ASSIGN: Channel Input Config:
5 GEAR: INH
6 AUX1: N/A
5. Go to the FUNCTION LIST
6. Set FLAP SYSTEM:
SELECT SWITCH D:
POS 0: 0% FLAP*
POS 1: 50% FLAP* 10% Elevator
POS 2: 100% FLAP* 20% Elevator
SPEED 2.0
7. Set MIXING: P-MIX 1
Select; NORMAL
Set INH > INH to read AIL > FL
RATE: 100% 100%
OFFSET: 0%
TRIM: INH
Switch: ON
8. Set MIXING: P-MIX 2
Select; NORMAL
Set INH > INH to read AIL > GEAR
RATE: -100% -100%
OFFSET: 0%
TRIM: INH
Switch: ON
9. Set MIXING: P-MIX 3
Select; NORMAL
Set INH > INH to read FL > GEAR
RATE: 100% 0%
OFFSET: 0%
TRIM: INH
Switch: ON
BNF advanced receiver setup (optional)
†
Some of the terminology and function locations used in the iX12 and iX20
programming may be slightly different than other Spektrum AirWare™ radios.
The names given in parenthesis correspond to the iX12 and iX20 programming
terminology. Consult your transmitter manual for specific information about
programming your transmitter.
* Flap programming values may vary slightly. For your initial flights use the
recommended flap travel settings provided in the Flaps section and adjust the flap
travel to your preference on subsequent flights.
AR631 advanced receiver setup port assignments
BND/PRG = Y-Harness: Lights/BIND
1 = Throttle
2 = Y-harness: Ailerons
3 = Elevator
4 = Rudder
5 = Left flap
6 = Right flap
Advanced Transmitter Setup
Start all transmitter programming with a blank ACRO model (perform a model
reset), then name the model.
Set Dual Rates to
HIGH 100%
LOW 70%
Set Servo Travel to 100%
Set Throttle Cut to -130%
DX7G2,
DX8G2,
DX8e
DX9,
DX18,
DX20,
iX12,
iX20
NX6
NX10
1. Go to the Model Utilities
2. Set MODEL TYPE: AIRPLANE
3. Set Model Setup, Aircraft Type:
WING: 1 AIL 2 FLAP
4. Go to the Model Adjust
5. Set FLAP SYSTEM:
SELECT SWITCH D:
POS 0: 0% FLAP*
POS 1: 50% FLAP* 10% Elevator
POS 2: 100% FLAP* 20% Elevator
SPEED 2.0
6. Set MIXING: P-MIX 1
Select; NORMAL
Set INH > INH to read (N) AIL > L FL
RATE: -100% -100%
OFFSET: 0%
TRIM: INH
Switch: ON
7. Go to the Model Utilities
8. Set CHANNEL ASSIGN, Channel Input:
CH 5: INH
9. Set CHANNEL ASSIGN, Rx Port Assignment:
CH 5: L FLAP