User Manual
EN
Lights
Bind Port
Right Flap
Left Flap
Ailerons
15
With the basic transmitter setup, the ailerons and fl aps will operate separately.
For increased aileron authority, the AR636 receiver included in the BNF version
may be confi gured so the fl aps can operate as both fl aps and ailerons.
Servo Plug Order Change
1. Remove the Y-harness plugged into the Ch-6 port on the AR636.
2. Insert two servo extensions (EFLREX9L) into the receiver ports; one in Ch-5
and one in Ch-6.
3. The left fl ap plugs into the Ch-5 extension. The right fl ap plugs into the
Ch-6 extension. We recommend labeling the wires to help identify the
correct ports when mounting the wing.
4. Insert the Y-harness into the BIND port. The lights plug into one side of the
Y-harness, and the other side serves as a BIND port.
CAUTION: Connecting servos to the wrong port on the receiver could
cause a crash.
IMPORTANT: A 7-channel or higher transmitter is required for the advanced BNF
receiver setup plus the ability to select between AS3X and SAFE with SAFE Select. If
using a 6 channel transmitter for the advanced receiver setup, only AS3X is available.
Advanced Transmitter Setup
Start all transmitter programming with a blank ACRO model (perform a model
reset), then name the model.
Set Dual Rates to
HIGH 100%
LOW 70%
Set Servo Travel to 100%
Set Throttle Cut to -130%
DX6e
DX6 (Gen2)
1. Go to the SYSTEM SETUP
2. Set MODEL TYPE: AIRPLANE
3. Set AIRCRAFT TYPE:
WING: 1 AIL 1 FLAP
4. Set CHANNEL ASSIGN: Rx Port Assignment:
5 GEAR: INH
6 AUX1: FLAP
5. Go to the FUNCTION LIST
6. Set FLAP SYSTEM:
SELECT SWITCH D:
POS 0: 0% FLAP*
POS 1: 50% FLAP* 10% Elevator
POS 2: 100% FLAP* 20% Elevator
SPEED 2.0
7. Set MIXING: P-MIX 1
Select; NORMAL
Set INH > INH to read N AIL > FL
RATE: 100% 100%
OFFSET: 0%
TRIM: INH
Switch: ON
8. Set MIXING: P-MIX 2
Select; NORMAL
Set INH > INH to read N AIL > GEAR
RATE: -100% -100%
OFFSET: 0%
TRIM: INH
Switch: ON
9. Set MIXING: P-MIX 3
Select; NORMAL
Set INH > INH to read FL > GEAR
RATE: 100% 0%
OFFSET: 0%
TRIM: INH
Switch: ON
DX8
1. Go to the SYSTEM SETUP
2. Set MODEL TYPE: AIRPLANE
3. Set WING TYPE: 1 AIL 2 FLAP
4. Go to the FUNCTION LIST
5. Set FLAP SYSTEM: Choose Flap
NORM: -0% FLAP*
MID: 50% FLAP* 10% Elevator
LAND: 100% FLAP* 20% Elevator
SPEED 2.0S: SWITCH = FLAP
6. Set MIXING: P-MIX 1
Select; NORMAL
Set INH > INH to read N AIL > L FL
RATE: 100% 100%
OFFSET: 0%
TRIM: INH
Switch: ON
BNF advanced receiver setup (optional)
†
Some of the terminology and function locations used in the iX12 programming may
be slightly different than other Spektrum AirWare™ radios. The names given in
parenthesis correspond to the iX12 programming terminology. Consult your transmitter
manual for specifi c information about programming your transmitter.
* Flap programming values may vary slightly. For your initial fl ights use the
recommended fl ap travel settings provided in the Flaps section and adjust the fl ap
travel to your preference on subsequent fl ights.
AR636 advanced receiver setup port assignments
BND/PRG = Y-Harness: Lights and BIND
1 = Throttle
2 = Y-harness: Ailerons
3 = Elevator
4 = Rudder
5 = Left fl ap
6 = Right fl ap
Advanced Transmitter Setup
DX7 (Gen2)
DX8e
DX8 (Gen2)
DX9
DX10t
DX18
DX20
iX12
1. Go to the SYSTEM SETUP (Model Utilities)
†
2. Set MODEL TYPE: AIRPLANE
3. Set AIRCRAFT TYPE (Model Setup, Aircraft Type)
†
:
WING: 1 AIL 2 FLAP
4. Set CHANNEL ASSIGN (Model Setup, Channel Assign)
†
:
Rx Port Assignment:
5 GEAR: L FLAP
6 AUX1: R FLAP
5. Go to the FUNCTION LIST (Model Adjust)
†
6. Set FLAP SYSTEM:
SELECT SWITCH D:
POS 0: 0% FLAP*
POS 1: 50% FLAP* 10% Elevator
POS 2: 100% FLAP* 20% Elevator
SPEED 2.0
7. Set MIXING: P-MIX 1
Select; NORMAL
Set INH > INH to read N AIL > L FL
RATE: 100% 100%
OFFSET: 0%
TRIM: INH
Switch: ON