ICON A5 Instruction Manual SAFE® Select Technology, Optional Flight Envelope Protection
EN NOTICE All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit www.horizonhobby.com and click on the support tab for this product.
EN Box Contents Quick Start Information Transmitter Setup Dual Rates 1. Set up your transmitter using the transmitter setup chart Hi Rate Low Rate Ail S20mm T18mm S15mm T12mm Ele 12mm 9mm Rud 25mm 18mm Center of Gravity (CG) 30-35mm back from leading edge of wing at the fuselage.
EN SAFE® Select Technology The evolutionary SAFE® Select technology can offer an extra level of protection so you can perform the first flight with confidence. No complex transmitter programming is required. Just follow the simple bind process to make the SAFE Select system active. When activated, bank and pitch limitations keep you from over-controlling and automatic self-leveling makes recovery from risky or confusing attitudes as simple as releasing the sticks.
EN Model Assembly Horizontal Tail Installation 1. Install the horizontal tail on the fuselage using the two screws (A). 2. Attach the clevis to the second most outer hole of the elevator control horn (B) and connect the opposite end of the control rod to the middle hole of the servo horn (C) as shown. 3. When needed, disassemble in reverse order.
EN Model Assembly Continued Wing Installation 1. Remove the battery hatch. 2. Guide the wing tube (A) through the hole located at the top of the fuselage as shown. 3. Slide each wing half (B) over the wing tube. 4. Connect the two aileron connectors to the aileron Y-harnesss at the root of each wing. Place extra servo wire slack and servo connectors in the small cavity in the root of the wing. A CAUTION: DO NOT crush or otherwise damage the wiring when attaching the wing to the fuselage. 5.
EN Model Assembly Continued Propeller Installation IMPORTANT: Install the propeller after all system setups are completed to reduce the chance of accidental propeller strike. 1. Install the collet (A) on the motor shaft (B). 2. Install the backplate (C), spinner backplate (D), propeller (E) and spinner nut (F) on the collet shaft. Use a tool to tighten the spinner nut on the collet shaft. 3. Install the spinner (G) on the spinner nut (F) using a screw (H).
EN Model Assembly Continued Main Gear Installation 1. Turn the model over so the bottom faces up. B 2. Install the rear right and left landing gear struts (A) in the fuselage using six screws (B). 2 X 8mm (6) Nose Gear Installation 1. Install the nose wheel post in the hole in front of the fuselage. 2. Put the Z-bend of the steering linkage (C) in the outermost hole of the steering arm (D). 3. Carefully turn over the model so it rests on the landing gear.
EN Transmitter and Receiver Binding / Switching ON and OFF SAFE Select This product requires an approved Spektrum™ DSM2®/DSMX® compatible transmitter. Visit www.bindnfly.com for a complete list of approved transmitters. Switching ON SAFE Select Binding Sequence The aircraft has an optional SAFE Select feature, which can be switched ON or OFF easily by binding in a specific manner as described below.
EN SAFE® Select Switch Designation SAFE® Select technology can be easily assigned to any open switch on your transmitter. With this new feature, you now have the flexibility to enable or disable the technology while in flight. Mode 1 and 2 Transmitters IMPORTANT: Before assigning your desired switch, ensure that the travel for that channel is set at 100%. Assigning a switch 1. Bind the aircraft correctly to activate SAFE Select. This will allow the system to be assigned to a switch. 2.
EN Battery Installation and ESC Arming Battery Selection We recommend the E-flite® 2200mAh 11.1V 3S 30C Li-Po battery (EFLB22003S30). Refer to the Optional Parts List for other recommended batteries. If using a battery other than those listed, the battery should be within the range of capacity, dimensions and weight of the E-flite Li-Po battery packs to fit in the fuselage. Be sure the model balances at the recommended CG. 1. Lower the throttle and throttle trim to the lowest settings.
EN Center of Gravity (CG) The CG location is measured from the leading edge of the wing at the root. This CG location has been determined with the recommended Li-Po battery (EFLB22003S30) installed all the way forward in the battery compartment. 30-35mm back from leading edge of wing at the fuselage. AS3X Control Direction Test This test ensures that the AS3X® control system is functioning properly. Assemble the aircraft and bind your transmitter to the receiver before performing this test. 1.
EN In Flight Trimming During your first flight, trim the aircraft for level flight at 3/4 throttle. Make small trim adjustments with your transmitter’s trim switches to straighten the aircraft’s flight path. 3 Seconds After adjusting trim, do not touch the control sticks for 3 seconds. This allows the receiver to learn the correct settings to optimize AS3X performance. Failure to do so could affect flight performance. Flying Tips and Repairs Consult local laws and ordinances before choosing a flying location.
EN Post Flight 1. Disconnect the flight battery from the ESC (Required for Safety and battery life). 2. Power OFF the transmitter. 3. Remove the flight battery from the aircraft. 4. Recharge the flight battery. 5. Repair or replace all damaged parts. 6. Store the flight battery apart from the aircraft and monitor the battery charge. 7. Make note of the flight conditions and flight plan results, planning for future flights.
EN PNP Receiver Selection and Installation The Spektrum AR636 receiver er is recommended for ths airplane. If you choose to install another receiver, ensure nsure that it is at least a 5-channel full range (sport) receiver. Refer to yourr receiver manual for correct installation and operation instructions. Installation (AR636 shown) 1. Remove the canopy from m the fuselage. 2. Mount the receiver parallel lel to the length of the fuselage as shown. Use double-sided servo tape.
EN Troubleshooting Guide Problem Aircraft will not respond to throttle but responds to other controls Extra propeller noise or extra vibration Reduced flight time or aircraft underpowered Aircraft will not Bind (during binding) to transmitter Aircraft will not connect (after binding) to transmitter Possible Cause Throttle not at idle and/or throttle trim too high Motor power pulses then motor loses power 16 Reset controls with throttle stick and throttle trim at lowest setting Throttle servo travel
EN AMA National Model Aircraft Safety Code Effective January 1, 2014 A. GENERAL A model aircraft is a non-human-carrying aircraft capable of sustained flight in the atmosphere. It may not exceed limitations of this code and is intended exclusively for sport, recreation, education and/or competition. All model flights must be conducted in accordance with this safety code and any additional rules specific to the flying site. 1. Model aircraft will not be flown: (a) In a careless or reckless manner.
EN Limited Warranty What this Warranty Covers Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the product purchased (the “Product”) will be free from defects in materials and workmanship at the date of purchase.
EN Contact Information Country of Purchase United States of America Horizon Hobby Horizon Service Center (Repairs and Repair Requests) Horizon Product Support (Product Technical Assistance) Sales United Kingdom Germany Service/Parts/Sales: Horizon Hobby Limited Horizon Technischer Service Sales: Horizon Hobby GmbH France Service/Parts/Sales: Horizon Hobby SAS Phone Number/Email Address servicecenter.horizonhobby.com/ RequestForm/ productsupport@horizonhobby.com 877-504-0233 websales@horizonhobby.
Replacement Parts • Ersatzteile • Pièces de rechange • Pezzi di ricambio Part # | Nummer Description Beschreibung Description Descrizione EFL5803 Prop with Spinner: ICON A5 Propeller mit Spinner: ICON A5 Cône avec hélice: ICON A5 Elica con ogiva: ICON A5 EFL5801 Decal Sheet: ICON A5 Dekorbogen: ICON A5 Planche de décoration: ICON A5 Foglio adesivi: ICON A5 EFL5810 Landing Gear Set: ICON A5 Fahrwerkset: ICON A5 Set de train d’atterrissage: ICON A5 Set carrelli: ICON A5 EFL5804 Prop Adapt
Optional Parts • Optionale Bauteile • Pièces optionnelles • Pezzi opzionali Part # | Nummer Description Beschreibung EFLA250 Park Flyer Tool Assortment, 5 pc Park Flyer Werkzeugsortiment, 5-teilig Assortiment d'outils park flyer, 5pc Park Flyer assortimento attrezzi, 5 pz EFLAEC302 EC3 Battery Connector, Female (2) EC3 Akkukabel, Buchse (2) Prise EC3 femelle (2pc) EC3 connettore femmina x batteria (2) EFLAEC303 EC3 Device/Battery Connector, Male/ Female EC3 Kabelsatz, Stecker/Buchse Prise EC3
© 2016 Horizon Hobby, LLC. E-flite, AS3X, DSM, DSM2, DSMX, the DSMX logo, Bind-N-Fly, SAFE, the SAFE logo, Z-Foam, ModelMatch, Dynamite, EC3, Prophet and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, LLC. The Spektrum trademark is used with permission of Bachmann Industries, Inc. Futaba is a registered trademark of Futaba Denshi Kogyo Kabushiki Kaisha Corporation of Japan.
