User Manual

 a.ToselectNoBrake/BrakeOff—Youwillhear1shortbeep.Movethe
throttlesticktocenter.TheESCwillbeep2times,indicatingyouhaveset
theprogramselection.Leaveinfullthrottlefor5secondstoadvancetothe
nextselection.
 b.ToselectSoftBrake—Youwillhear2shortbeeps.Movethethrottlestick
tocenter.TheESCwillbeep2times,indicatingyouhavesettheprogram
selection.Leaveinfullthrottlefor5secondstoadvancetothenext
selection.
 c.ToselectMediumBrake—Youwillhear3shortbeeps.Movethethrottle
sticktocenter.TheESCwillbeep2times,indicatingyouhavesetthe
programselection.Leaveinfullthrottlefor5secondstoadvancetothe
nextselection.
 d.ToselectHardBrake—Youwillhear4shortbeeps.Movethethrottlestick
tocenter.TheESCwillbeep2times,indicatingyouhavesettheprogram
selection.Leaveinfullthrottlefor5secondstoadvancetotherst
selectionagain.
PROGRAMMING MENU 3 – TIMING
The default setting is 15 degrees.
Asageneralrule,lowerpolecountmotorsuselowertimingandhigherpole
countmotorsusehighertiming.Pleaserefertoyourmotorinstructionsand
specicationsforanindicationofthenumberofpoles.
LOW TIMING ADVANCE
TimingDegrees 5&10
MotorPoles 2to4
ExpectedPerformance Goodbalanceofpowerandefciency
MotorPoles 6ormore
ExpectedPerformance Bestefciencyandruntime(lowestpower)
STANDARD TIMING ADVANCE
TimingDegrees 15&20
MotorPoles 6to12
ExpectedPerformance Goodbalanceofpowerandefciency
MotorPoles 14ormore
ExpectedPerformance Bestefciencyandruntime(lowestpower)
HIGH TIMING ADVANCE
TimingDegrees 25
MotorPoles 12
ExpectedPerformance Highestpower,lessefciency
MotorPoles 14ormore
ExpectedPerformance Goodbalanceofpowerandefciency
1.Movethesticktocenterfor5secondsandtheESCwillbeep3times,
indicatingyouarenowinMenu3.
2.MovethethrottlesticktofullthrottlepositiontomakechangestotheTiming
programming.
 a.Toselect5Degrees—Youwillhear1shortbeep.Movethethrottlestick
tocenter.TheESCwillbeep2times,indicatingyouhavesettheprogram
selection.Leaveinfullthrottlefor5secondstoadvancetothenext
selection.
 b.Toselect10Degrees—Youwillhear2shortbeeps.Movethethrottlestick
tocenter.TheESCwillbeep2times,indicatingyouhavesettheprogram
selection.Leaveinfullthrottlefor5secondstoadvancetothenext
selection.
 c.Toselect15Degrees—Youwillhear3shortbeeps.Movethethrottlestick
tocenter.TheESCwillbeep2times,indicatingyouhavesettheprogram
selection.Leaveinfullthrottlefor5secondstoadvancetothenext
selection.
 d.Toselect20Degrees—Youwillhear4shortbeeps.Movethethrottlestick
tocenter.TheESCwillbeep2times,indicatingyouhavesettheprogram
selection.Leaveinfullthrottlefor5secondstoadvancetothenext
selection.
 e.Toselect25Degrees—Youwillhear5shortbeeps.Movethethrottlestick
tocenter.TheESCwillbeep2times,indicatingyouhavesettheprogram
selection.Leaveinfullthrottlefor5secondstoadvancetotherst
selectionagain.
PROGRAMMING MENU 4 – THROTTLE INPUT RANGE (PWM)
The default setting is 1.2ms to 1.8ms (works with most radio systems).
Thisoptionallowsforproperthrottleinputwithmanydifferentradiosystems.
However,someradioshaveawideroutputrange,andmaygiveamorelinear
responsewiththe1.1msto1.9msrange.Ifyoufeelthereistoomuch“dead”
areainthestickmovementnearfullthrottle,tryadjustingtheendpointsinyour
radio,orchangetothewiderinputrange.Beawarethatifthesesettingsarenot
correct,itmaybeimpossibletoarmtheESC.
1.Movethesticktocenterfor5secondsandtheESCwillbeep4times,
indicatingyouarenowinMenu4.
2.MovethethrottlesticktofullthrottletomakechangestotheThrottleInput
Rangeprogramming.
 a.Toselect1.2msto1.8ms—Youwillhear1shortbeep.Movethethrottle
sticktocenter.TheESCwillbeep2times,indicatingyouhavesetthe
programselection.Leaveinfullthrottlefor5secondstoadvancetothe
nextselection.
 b.Toselect1.1msto1.9ms—Youwillhear2shortbeeps.Movethethrottle
sticktocenter.TheESCwillbeep2times,indicatingyouhavesetthe
programselection.Leaveinfullthrottlefor5secondstoadvancetothe
rstselectionagain.
PROGRAMMING MENU 5 – START-UP RATE
The default setting is 0.25 seconds.
Thestart-uprateisthetimeittakestoreachmaximummotorspeed.Changing
thesettingto1secondcanbeusefulwithpower-fragilegearboxes.
1.Movethesticktocenterfor5secondsandtheESCwillbeep5times,
indicatingyouarenowinMenu3.
2.MovethethrottlesticktofullthrottlepositiontomakechangestotheStart-up
Rateprogramming.
 a.Toselect.25second—Youwillhear1shortbeep.Movethethrottlestick
tocenter.TheESCwillbeep2times,indicatingyouhavesettheprogram
selection.Leaveinfullthrottlefor5secondstoadvancetothenext
selection.
 b.Toselect1second—Youwillhear2shortbeeps.Movethethrottlestick
tocenter.TheESCwillbeep2times,indicatingyouhavesettheprogram
selection.Leaveinfullthrottlefor5secondstoadvancetotherst
selectionagain.
PROGRAMMING MENU 6 – PWM SWITCHING FREQUENCY
The default setting is 8KHz (acceptable for most motors).
Ifyouhavealoworverylowinductancemotorandknowyouneedtousea
higherPWMFrequency(refertothemanualincludedwiththemotor),thenyou
canchangethesetting.Otherwise,werecommendleavingthedefaultsetting.
1.Movethesticktocenterfor5secondsandtheESCwillbeep6times,
indicatingyouarenowinMenu6.
2.MovethethrottlesticktofullthrottletomakechangestothePWMSwitching
Frequencyprogramming.
 a.Toselect8KHzPWMFrequency—Youwillhear1shortbeep.Movethethrottle
sticktocenter.TheESCwillbeep2times,indicatingyouhavesettheprogram
selection.Leaveinfullthrottlefor5secondstoadvancetothenextselection.
 b.Toselect16KHzPWMFrequency—Youwillhear2shortbeeps.Movethe
throttlesticktocenter.TheESCwillbeep2times,indicatingyouhavesetthe
programselection.Leaveinfullthrottlefor5secondstoadvancetothenext
selection.
 c.Toselect32KHzPWMFrequency—Youwillhear3shortbeeps.Movethe
throttlesticktocenter.TheESCwillbeep2times,indicatingyouhavesetthe
programselection.Leaveinfullthrottlefor5secondstoadvancetotherst
selectionagain.