™ ® UMX RADIAN Instruction Manual Bedienungsanleitung Manuel d’utilisation Manuale di Istruzioni
NOTICE All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, Inc. For up-to-date product literature, visit www.horizonhobby.com and click on the support tab for this product.
Box Contents Installed Dual Rates Included High 100 % 8.5mm Brushed Motor Low 70% Timer Settings First Flight 8 Min. DSM2®/DSMX® AS3X Receiver/ESC USB Li-Po Charger 10 Min. To register your product online, go to www.e-fliterc.com 2 x (SPMSA2030L) on the board Required to Complete: DSM2/DSMX 4-Channel Transmitter Specifications 28.7 in (730mm) 16.5 in (418mm) 31mm 1.50 oz (43 g) The CG location is 31mm back from the leading edge at the wing root.
Charging Warnings The Battery Charger (EFLC1008) included with your aircraft has been designed to safely charge the Li-Po battery. CAUTION: All instructions and warnings must be followed exactly. Mishandling of Li-Po batteries can result in a fire, personal injury and/or property damage. • By handling, charging or using the included Li-Po battery, you assume all risks associated with lithium batteries. • If at any time the battery begins to balloon or swell, discontinue use immediately.
Wing Installation 1. Slide the wing into the wing slot on the fuselage until the holes line up with the screw holes on the bottom. 2. Secure the wing using 2 screws. 3. Cut the loop tape (A) into 3 pieces and apply them around the screws in the battery holder, as shown. A Transmitter and Receiver Binding Binding Procedure Reference Table 1. Refer to your transmitter instructions for binding to a receiver. 2. Make sure the flight battery is disconnected from the aircraft. 3.
Installing the Flight Battery and Arming the ESC Arming the ESC also occurs after binding as previously described, but subsequent connection of a flight battery requires the following steps. AS3X The AS3X® system will not activate until the throttle stick or trim is increased for the first time. Once active, the control surfaces may move rapidly and noisily on the aircraft. This is normal. AS3X technology will remain active until the battery is disconnected.
Control Direction Test Move the controls on the transmitter to make sure the aircraft control surfaces move correctly. Always keep throttle at the low position during testing. Down Elevator Up Elevator Left Rudder Right Rudder Control Centering Before first flights, or in the event of a crash, make sure the control surfaces are centered when the transmitter controls and trims are neutral. The transmitter sub-trim must be set to zero.
Flying Tips Consult local laws and ordinances before choosing a location to fly your aircraft. We recommend flying your aircraft outside in no greater than moderate winds or inside in a large gymnasium. Always avoid flying near houses, trees, wires and buildings. You should also be careful to avoid flying in areas where there are many people, such as busy parks, schoolyards or soccer fields. For additional tips on flying, refer to the product page at horizonhobby.com. drift downwind.
Flying Tips continued Low Voltage Cutoff (LVC) Repairs Low Voltage Cutoff (LVC) pulses the power to the motor when the voltage gets low. When the motor power pulses, land the aircraft immediately and recharge the flight battery. Disconnect and remove the Li-Po battery from the aircraft after use to prevent trickle discharge. Fully charge your Li-Po battery before storing it. During storage, make sure the battery charge does not fall below 3V per cell.
Motor Service CAUTION: DO NOT handle propeller parts while the flight battery is connected. Personal injury could result. IMPORTANT: Removing tape or decals can remove paint from the fuselage. NOTICE: DO NOT remove the gearbox from the aircraft. Damage to the aircraft will result. • Hold the prop shaft using needle-nose pliers or hemostats to remove the propeller and prop nut. • Correctly align the prop shaft gear with the pinion gear on the motor.
Troubleshooting Guide AS3X Problem Possible Cause Solution Control surfaces not at neutral position when transmitter controls are at neutral Control surfaces may not have been mechanically centered from factory Center control surfaces mechanically by adjusting the U-bends on control linkages Aircraft was moved after the flight battery was connected and before sensors initialized Disconnect and reconnect the flight battery while keeping the aircraft still for 5 seconds Model flies inconsistently from fli
Troubleshooting Guide (continued) Problem Possible Cause LED on receiver Transmitter is too near aircraft during flashes rapidly binding process and aircraft will not bind to transmitter (during binding) Bind switch or button was not held while transmitter was powered on LED on receiver flashes rapidly and aircraft will not respond to transmitter (after binding) Solution Power off transmitter, move transmitter a larger distance from aircraft, disconnect and reconnect flight battery to aircraft and follow bi
Limited Warranty What this Warranty Covers Horizon Hobby, Inc. (“Horizon”) warrants to the original purchaser that the product purchased (the “Product”) will be free from defects in materials and workmanship at the date of purchase.
the outside of the shipping carton. NOTICE: Do not ship LiPo batteries to Horizon. If you have any issue with a LiPo battery, please contact the appropriate Horizon Product Support office. Warranty Requirements For Warranty consideration, you must include your original sales receipt verifying the proofof-purchase date. Provided warranty conditions have been met, your Product will be serviced or replaced free of charge. Service or replacement decisions are at the sole discretion of Horizon.
Compliance Information for the European Union Declaration of Conformity (in accordance with ISO/IEC 17050-1) No. HH2014010402 Product(s): EFL UMX Radian BNF Item Number(s): EFLU2980 Equipment class: 1 The object of declaration described above is in conformity with the requirements of the specifications listed below, following the provisions of the European R&TTE directive 1999/5/EC, EMC Directive 2004/108/EC and LVD Directive 2006/95/EC EN 301 489-1 V1.9.2: 2012 EN 301 489-17 V2.1.
Replacement Parts • Ersatzteile • Pièces de rechange • Pezzi di ricambio Part # • Nummer Numéro • Codice EFLU2903 EFLU2901 EFLU2902 EFLU2920 EFLU2925 EFLU2967 EFLU2922 EFLB1501S25 SPMAR5430L EFLU2916 EFLU2927 EFL9054 Description Beschreibung Ultra Micro Radian: Spinner Set (3): Ultra Micro Radian Spinner Set E-flite Ultra Decal Sheet: Ultra Micro Radian: Micro Radian Dekorbogen E-flite Ultra Micro Folding Propeller: Radian KlappUltra Micro Radian Propeller Main Wing: Ultra Ultra Micro Radian: Micro Rad
Optional Parts and Accessories • Optionale Bauteile und Zubehör • Pièces et accessoires optionnels • Componenti e accessori opzionali Part # | Nummer Description Numéro | Codice EFLC1000 EFLC1004 EFLB1501S45 EFLC1005/ AU/EU/UK AC/DC 3.7V Li-Po Charger Celectra 4-Port 1S 3.7V 0.3 A DC Li-Po Charger Beschreibung AC/DC-3,7V-Li-PoLadegerät E-flite 4 Port Ladegerät 1S 3,7V 0,3A Description Chargeur Li-Po CA/DC 3,7V Chargeur Li-Po CC 0,3 A 3,7V 1S 4 ports Celectra Li-Po 150mAh 1S 3.7V 1S 3.
© 2013 Horizon Hobby, Inc. E-flite, Radian, AS3X, Blade, Celectra, UMX, DSM, DSM2, DSMX, ModelMatch, Bind-N-Fly, the Bind-N-Fly logo and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, Inc. The Spektrum trademark is used with permission of Bachmann Industries, Inc. Futaba is a registered trademark of Futaba Denshi Kogyo Kabushiki Kaisha Corporation of Japan. All other trademarks, service marks and logos are property of their respective owners. US D578, 146. US 7,898,130.
