Ultra Micro B-17G Flying Fortress Instruction Manual Bedienungsanleitung Manuel d’utilisation Manuale di Istruzioni
EN NOTICE All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit www.horizonhobby.com and click on the support tab for this product.
EN Table of Contents Charger Warnings ..................................................4 Battery Charging....................................................4 Transmitter and Receiver Binding...........................5 Low Voltage Cutoff (LVC) ........................................5 ESC/Receiver Arming, Battery Installation and Center of Gravity .............................................6 Control Direction Tests ...........................................7 Control Centering .........................
EN Charger Warnings The battery charger (EFLC1008) included with your aircraft has been designed to safely charge the Li-Po battery. CAUTION: All instructions and warnings must be followed exactly. Mishandling of Li-Po batteries can result in a fire, personal injury and/or property damage. • By handling, charging or using the included Li-Po battery, you assume all risks associated with lithium batteries. • If at any time the battery begins to balloon or swell, discontinue use immediately.
EN Transmitter and Receiver Binding Binding is the process of programming the receiver to recognize the GUID (Globally Unique Identifier) code of a single specific transmitter. You need to ‘bind’ your chosen Spektrum™ DSM2/DSMX technology equipped aircraft transmitter to the receiver for proper operation. Any full range Spektrum DSM2/DSMX transmitter can bind to the DSM2/DSMX receiver. Please visit www. bindnfly.com for a complete list of compatible transmitters.
EN ESC/Receiver Arming, Battery Installation and Center of Gravity CAUTION: Always keep hands away from the propellers. When armed, the motors will turn the propeller in response to any throttle movement. 1 Arming the ESC/receiver also occurs after binding as previously described, but subsequent connection of a flight battery requires the following steps. AS3X The AS3X® system will not activate until the throttle stick or trim is increased for the first time.
EN Control Direction Tests Traditional Control Direction Test You should bind your aircraft and transmitter before doing these tests. Move the controls on the transmitter to make sure the aircraft control surfaces move correctly and in the proper direction. Make sure the tail linkages move freely and that paint or decals are not adhered to them. AS3X® Control Direction Test This test ensures that the AS3X® control system is functioning properly. 3.
EN Control Centering Before the first flights, or in the event of an accident, make sure the flight control surfaces are centered. Adjust the linkages mechanically if the control surfaces are not centered. Use of the transmitter sub-trims may not correctly center the aircraft control surfaces due to the mechanical limits of linear servos. 1. Make sure the control surfaces are neutral when the transmitter controls and trims are centered. The transmitter sub-trim must always be set to zero. 2.
EN Flying Tips and Repairs We recommend flying your aircraft outside in calm conditions. Always avoid flying near houses, trees, wires and buildings. You should also be careful to avoid flying in areas where there are many people, such as busy parks, schoolyards or soccer fields. Consult local laws and ordinances before choosing a location to fly your aircraft.
EN Power Components Service CAUTION: DO NOT handle propeller parts while the flight battery is connected. Personal injury could result. Disassembly IMPORTANT: Service only one motor at a time. Propellers and hardware are not interchangeable. 1. Disconnect the battery from the ESC/receiver. 2. Carefully cut the tape on each nacelle and remove the bottom half. IMPORTANT: Removing tape or decals can remove paint from the fuselage. I ve Insta mo ll e ov tall Rem ns 4.
EN Installing the Retracted Landing Gear To Install the retracted landing gear: 1. Insert the retracted landing gear into the retaining slot in the nacelle as shown. Tip: Install the retracted landing gear for handlaunching and landing on grass. While these are installed, avoid landing on concrete or pavement. Installing the Landing Gear To install the included landing gear: 1. Insert the landing gear strut wire into the retaining slot in the nacelle as shown.
EN Troubleshooting Guide AS3X Problem Possible Cause Solution Control surfaces not at neutral position when transmitter controls are at neutral Control surfaces may not have been mechanically centered from factory Center control surfaces mechanically by adjusting the U-bends on control linkages Aircraft was moved after the flight battery was connected and before sensors initialized Disconnect and reconnect the flight battery while keeping the aircraft still for 5 seconds Model flies inconsistently fro
EN Troubleshooting Guide (Continued) Problem Possible Cause Solution LED on receiver flashes Less than a 5-second wait between first rapidly and aircraft will powering on transmitter and connecting not respond to transmit- flight battery to aircraft ter (after binding) Aircraft bound to different model memory (ModelMatch™ radios only) Control surface does not move Leaving transmitter on, disconnect and reconnect flight battery to aircraft Select correct model memory on transmitter and disconnect and recon
EN exclusive remedy shall be that Horizon will, at its option, either (i) service, or (ii) replace, any Product determined by Horizon to be defective. Horizon reserves the right to inspect any and all Product(s) involved in a warranty claim. Service or replacement decisions are at the sole discretion of Horizon. Proof of purchase is required for all warranty claims. SERVICE OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY.
EN Warranty and Service Information Country of Purchase Horizon Hobby Phone Number/Email Address Address Horizon Service Center (Repairs and Repair Requests) United States of America United Kingdom Germany France China servicecenter.horizonhobby. com/RequestForm/ www.quickbase.com/db/ Horizon Product Support 4105 Fieldstone Rd bghj7ey8c?a=GenNewRecord (Product Technical Assistance) Champaign, Illinois, 61822 USA 888-959-2305 sales@horizonhobby.com Sales 888-959-2305 sales@horizonhobby.co.
Replacement Parts – Ersatzteile – – Pièces de rechange – Pezzi di ricambio – Part # • Nummer Description Numéro • Codice Beschreibung Description Descrizione EFLU5302 Decals : UMX B-17G E-flite UMX B-17G: Dekorbogen Planche de décoration : UMX B-17G Adesivi: UMX B-17G EFLU5303 Landing gear : UMX B-17G E-flite UMX B-17G: Fahrwerk Train d’atterrissage : UMX B-17G Carrello: UMX B-17G EFLU5304 Nose/Battery Hatch: UMX B-17G E-flite UMX B-17G: Akkuklappe Nase Nez/trappe à batterie : UMX B-17G Portel
– Optional Parts and Accessories – – Optionale Bauteile und Zubehörteile – – Pièces optionnelles et accessoires – – Pezzi opzionali e accessori – Part # • Nummer Numéro • Codice PKZ1039 EFLA208 Description Beschreibung Description Descrizione Hook and Loop Set (5): Ultra Micros Parkzone: Klettband Set Ultra Micros Ultras Micros - Bande Set fascette a strappo auto-agrippante (5) (5): Ultra Micro Foam CA 1 oz/ Activator, 2 oz Pack E-flite CA Kleber Schaum-geeignet / Aktivatorspray 2 oz.
© 2014 Horizon Hobby, LLC. E-flite, AS3X, Blade, Celectra, DSM, DSM2, DSMX, ModelMatch, Bind-N-Fly, the Bind-N-Fly logo and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, LLC. The Spektrum trademark is used with permission of Bachmann Industries, Inc. Futaba is a registered trademark of Futaba Denshi Kogyo Kabushiki Kaisha Corporation of Japan. All other trademarks, service marks and logos are property of their respective owners. US 7,898,130. US D578,146.
