P-51D Mustang 1.
EN NOTICE All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit www.horizonhobby.com and click on the support tab for this product.
EN Box Contents Quick Start Information Transmitter Setup Dual Rates Set up your transmitter using the transmitter setup chart Hi Rate Low Rate Ail 12mm 8mm Ele 15mm 11mm Rud 15mm 10mm Flaps =50mm Landing Takeoff =11mm Center of Gravity (CG) 85mm +/- 3 back from leading edge at the root.
EN Preflight 1 Remove and inspect contents. 10 Test the retract operation. 2 Read this instruction manual thoroughly. 11 Test the flap operation. 3 Charge the flight battery. 12 Perform the Control Direction Test with the transmitter. 4 Setup Transmitter using transmitter setup chart. 13 Perform the AS3X Control Direction Test with the aircraft. 5 Fully assemble the airplane. 14 Adjust flight controls and transmitter. 6 Install the flight battery in the aircraft (once it has been fully charged).
EN Model Assembly Horizontal Tail Installation 1. Slide the horizontal tail tube (A) into the hole in the rear of the fuselage. A 2. Install the 2 piece (left and right) horizontal tail as shown. Ensure the control horn faces down. 3. Secure the two horizontal tail pieces in place using the 2 included screws (B). 4. Attach the clevis to the elevator control horn (see instructions for clevis connection).
EN Model Assembly Continued Wing Installation 1. Remove the canopy hatch. 2. Guide the Flaps, Retracts and Aileron servo connectors (A) through the hole (B) located in the bottom of the fuselage as shown. Tip: If needed, use hemostats or pliers to pull the servo connectors into the fuselage. 3. Connect the Flaps, Retracts and Aileron connectors to respective Y-harnesses connected to the receiver. The left and right servos can be connected to either side of a Y-harness.
EN Model Assembly Continued Propeller Installation IMPORTANT: It is recommended to install the propeller after all system setups are completed to reduce the chance of accidental propeller strike. E 1. Install spinner back plate (E), Propeller (D) and collet (C) onto motor shaft (F). The propeller size numbers (10.5 x 8) must face out from the motor for correct propeller operation. 2. Tighten collet by using a small screw driver or hex wrench inserted into small hole (Inset). F D C B 3.
EN Optional Drop Tank and Antenna Mast Installation Drop Tank Slide the optional drop tanks (A) into the rails (B) on each wing. A Check the Center of Gravity with the drop tanks installed. See the Adjusting the Center of Gravity instructions for more information. Antenna Mast B Slide the antenna mast (C) into slot (D) on top of the fuselage.
EN Battery Installation and ESC Arming Battery Selection A We recommend the E-flite® 2200mAh 11.1V 3S 30C Li-Po battery (EFLB22003S30). Refer to the Optional Parts List for other recommended batteries. If using a battery other than those listed, the battery should be within the range of capacity, dimensions and weight of the E-flite Li-Po battery packs to fit in the fuselage. Be sure the model balances at the recommended CG. 1. Lower the throttle and throttle trim to the lowest settings.
EN Center of Gravity (CG) The CG location is measured from the leading edge of the wing at the root. This CG location has been determined with the recommended Li-Po battery (EFLB22003S30) installed to the front edge of the battery tray. Tip: Measure the CG with the aircraft inverted. 85mm +/-3 back from leading edge at the root. AS3X Control Direction Test This test ensures that the AS3X® control system is functioning properly.
EN In Flight Trimming During your first flight, trim the aircraft for level flight at 3/4 throttle with flaps and gear up. Make small trim adjustments with your transmitter’s trim switches to straighten the aircraft’s flight path. 3 Seconds After adjusting trim do not touch the control sticks for 3 seconds. This allows the receiver to learn the correct settings to optimize AS3X performance. Failure to do so could affect flight performance.
EN Post Flight 1 Disconnect the flight battery from the ESC (Required for Safety and battery life). 5 Repair or replace all damaged parts. 2 Power OFF the transmitter. 6 Store the flight battery apart from the aircraft and monitor the battery charge. 3 Remove the flight battery from the aircraft. 7 4 Recharge the flight battery. Make note of the flight conditions and flight plan results, planning for future flights.
EN Troubleshooting Guide Problem Aircraft will not respond to throttle but responds to other controls Extra propeller noise or extra vibration Reduced flight time or aircraft underpowered Aircraft will not Bind (during binding) to transmitter Aircraft will not connect (after binding) to transmitter Possible Cause Throttle not at idle and/or throttle trim too high Reset controls with throttle stick and throttle trim at lowest setting Throttle servo travel is lower than 100% Make sure throttle servo t
EN AMA National Model Aircraft Safety Code Effective January 1, 2014 A. GENERAL A model aircraft is a non-human-carrying aircraft capable of sustained flight in the atmosphere. It may not exceed limitations of this code and is intended exclusively for sport, recreation, education and/or competition. All model flights must be conducted in accordance with this safety code and any additional rules specific to the flying site. 1. Model aircraft will not be flown: (a) In a careless or reckless manner.
EN Limited Warranty What this Warranty Covers Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the product purchased (the “Product”) will be free from defects in materials and workmanship at the date of purchase.
EN Contact Information Country of Purchase Horizon Hobby Horizon Service Center (Repairs and Repair Requests) United States of America Horizon Product Support (Product Technical Assistance) Sales United Kingdom Germany France China Service/Parts/Sales: Horizon Hobby Limited Horizon Technischer Service Sales: Horizon Hobby GmbH Service/Parts/Sales: Horizon Hobby SAS Service/Parts/Sales: Horizon Hobby – China Phone Number/Email Address servicecenter.horizonhobby.com/ RequestForm/ www.quickbase.
IT Replacement Parts • Ersatzteile • Pièces de rechange • Pezzi di ricambio Part # | Nummer Description Numéro | Codice EFL8250 P-51D Mustang 1.2m BNF Basic Beschreibung Description Descrizione P-51D Mustang 1,2m BNF Basic P-51D Mustang 1.2m BNF Basic P-51D 1.2m - Cône diamètre 75mm pour hélice quadripale P-51D 1.2m - Planche de décoration P-51D Mustang 1.2m BNF Basic Ogiva quadripala 75mm: P-51D 1.2m Esagone adattatore elica: P-51D 1.2m Carrello d’atterraggio con gambe e portelli: P-51D 1.
P-51D Mustang 1.2m © 2015 Horizon Hobby, LLC. E-flite, AS3X, DSM, DSM2, DSMX, the DSMX logo, Bind-N-Fly, Z-Foam, ModelMatch, Dynamite, EC3, Celectra, Prophet and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, LLC. The Spektrum trademark is used with permission of Bachmann Industries, Inc. Futaba is a registered trademark of Futaba Denshi Kogyo Kabushiki Kaisha Corporation of Japan. All other trademarks, service marks and logos are property of their respective owners.
