Sukhoi SU-29MM (Gen 2) Instruction Manual Bedienungsanleitung Manuel d’utilisation Manuale di Istruzioni
EN NOTICE All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit www.horizonhobby.com and click on the support tab for this product.
EN Box Contents Quick Start Information Panic Feature Choose to fly your aircraft with the Panic feature ON or OFF and bind accordingly. Using the If you choose to fly with the Panic feature ON, you will need to follow the Panic transmitter setup section of this manual. Feature Hi Rate Expo Low Rate Expo Set (Dual Rates Ail 100% 40% 45% 10% & Expo) in Ele 100% 35% 25% 10% your 70% 8% Transmitter Rud 100% 15% Center of Gravity (CG) 82mm +/- 3.23 inches back from leading edge of wing at the fuselage.
EN Transmitter and Receiver Binding / Switching ON and OFF Panic Recovery Feature This product requires an approved Spektrum™ DSM2®/DSMX® compatible transmitter. Visit www.bindnfly.com for a complete list of approved transmitters. Switching ON Panic Feature Binding Sequence The aircraft has an optional panic feature, which can be switched ON or OFF easily by binding in a specific manner as described below.
EN Transmitter Setup If you intend on using the Panic Recovery feature, it is important to follow this transmitter setup chart to assign your transmitter switches correctly to operate the Panic Recovery feature. Use the provided charts to guide you through transmitter setup. Locate your specific transmitter in the chart and follow the numbered setup sequence.
EN Model Assembly Landing Gear Installation B 1. Install the landing gear strut (A) as shown. A 2. Install the U-cover (B) on the fuselage. 3. Install the fairings (C) on the strut. 4. Secure the landing gear assembly by using 4 screws (D). Tip: Carefully support the aircraft while installing or removing screws. Disassemble in reverse order. D 2 X 10mm (4) C Wing Installation 1. Slide the wing tube (A) into the fuselage.
EN Model Assembly Continued Horizontal Tail Installation 1. Slide the horizontal tail tube (A) into the hole in the rear of the fuselage. 2. Install the left and right horizontal tails (B) onto the fuselage as shown. Ensure the control horn faces down. B 3. Apply 4 pieces of tape (C) to the fuselage mounts (one on the top and bottom of each half of the horizontal tail). 4. Attach the linkage (D) to the outermost hole in the elevator servo arm using the link keeper (E). A 5.
EN Control Horn and Servo Arm Settings The table to the right shows the factory settings for the control horns and servo arms. Fly the aircraft at factory settings before making changes. Arms NOTICE: If control throws are changed from the factory settings, the AR636 gain values may need to be adjusted. Refer to the Spektrum AR636 manual for adjustment of gain values. Elevator After flying, you may choose to adjust the linkage positions for the desired control response. See the table to the right.
EN Center of Gravity (CG) The CG location is 82mm back from the leading edge of the wing at the root. For first flights, install the recommended flight battery all the way forward. Secure the battery with the strap as shown. Aircraft CG and weight is based on an E-flite 11.1V 2200mAh 30C battery (EFLB22003S30) installed. 82mm 3.23 inches back from the leading edge of the wing at the root.
EN AS3X Control Direction Test This test ensures that the AS3X® control system is functioning properly. Assemble the aircraft and bind your transmitter to the receiver before performing this test. CAUTION: Keep all body parts, hair and loose clothing away from a moving propeller, as these items could become entangled. IMPORTANT: The AR636 programming for this aircraft increases control surface movement when landing gear is down. AS3X Reaction Elevator 1.
EN Flying Tips and Repairs Consult local laws and ordinances before choosing a flying location. Range Check your Radio System Before you fly, range check the radio system. Refer to your specific transmitter instruction manual for range test information. Oscillation Once the AS3X system is active (after advancing the throttle for the first time), you will normally see the control surfaces react to aircraft movement.
EN Motor Service CAUTION: Always disconnect the flight battery from the aircraft before removing the propeller. Assembly Assemble in reverse order. Disassembly 1. Remove the screw (A) and spinner (B) from the collet (C). 2. Remove the spinner nut (D), propeller (E), spinner backplate (F), backplate (G) and collet from the motor shaft (H). You will need a tool to turn the spinner nut. 3. Remove the 3 screws (I) from the cowling (J). Carefully remove the cowling from the fuselage.
EN Troubleshooting Guide Problem Aircraft will not respond to throttle but responds to other controls Extra propeller noise or extra vibration Reduced flight time or aircraft underpowered Aircraft will not Bind (during binding) to transmitter Possible Cause Solution Throttle not at idle and/or throttle trim too high Reset controls with throttle stick and throttle trim at lowest setting Throttle servo travel is lower than 100% Make sure throttle servo travel is 100% or greater Throttle channel is r
EN AMA National Model Aircraft Safety Code Effective January 1, 2014 A. GENERAL A model aircraft is a non-human-carrying aircraft capable of sustained flight in the atmosphere. It may not exceed limitations of this code and is intended exclusively for sport, recreation, education and/or competition. All model flights must be conducted in accordance with this safety code and any additional rules specific to the flying site. 1. Model aircraft will not be flown: (a) In a careless or reckless manner.
EN Limited Warranty What this Warranty Covers Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the product purchased (the “Product”) will be free from defects in materials and workmanship at the date of purchase.
EN Contact Information Country of Purchase United States of America Horizon Hobby Horizon Service Center (Repairs and Repair Requests) Horizon Product Support (Product Technical Assistance) Sales United Kingdom Germany France Service/Parts/Sales: Horizon Hobby Limited Horizon Technischer Service Sales: Horizon Hobby GmbH Service/Parts/Sales: Horizon Hobby SAS Phone Number/Email Address servicecenter.horizonhobby.com/ RequestForm/ productsupport@horizonhobby.com 877-504-0233 websales@horizonhobby.
Replacement Parts • Ersatzteile • Pièces de rechange • Pezzi di ricambio Part # | Nummer Numéro | Codice Description Beschreibung Description Descrizione SU-29MM (Gen 2) - Planche de décoration SU-29MM (Gen 2) - Cône Jambes de train principal : SU-29MM Clé d’aile : SU-29MM Set adesivi: SU-29MM (Gen 2) SU-29MM (Gen 2) - Trappe/Cockpit Portello e capottina SU-29MM (Gen 2) EFL8802 Decal Set: SU-29MM (Gen 2) Dekorbogen: SU-29MM (Gen 2) EFL8808 PKZ8006 PKZ8021 EFL8805 Spinner: SU-29MM (Gen 2) Main g
Sukhoi SU-29MM © 2016 Horizon Hobby, LLC. E-flite, AS3X, DSM, DSM2, DSMX, the DSMX logo, Bind-N-Fly, SAFE, Z-Foam, ModelMatch, Dynamite, EC3, Prophet and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, LLC. The Spektrum trademark is used with permission of Bachmann Industries, Inc. Futaba is a registered trademark of Futaba Denshi Kogyo Kabushiki Kaisha Corporation of Japan. All other trademarks, service marks and logos are property of their respective owners. US 9,056,667.