Timber X 1.
EN NOTICE All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit www.horizonhobby.com and click on the support tab for this product.
EN Box Contents Quick Start Information Transmitter Setup Dual Rates Set up your transmitter using the transmitter setup chart Hi Rate Low Rate Ail 33mm 33mm 25mm 25mm Ele 22mm 16mm Rud 30mm 20mm Flaps Full =35mm Half =20mm Center of Gravity (CG) 82mm-92mm back from leading edge of wing at the fuselage.
EN SAFE® Select Technology (BNF Basic) The evolutionary SAFE® Select technology can offer an extra level of protection so you can perform the first flight with confidence. No complex transmitter programming is required. Just follow the simple bind process to make the SAFE Select system active. When activated, bank and pitch limitations keep you from over-controlling and automatic self-leveling makes recovery from risky or confusing attitudes as simple as releasing the sticks.
EN Model Assembly Landing Gear Installation Mount the Landing Gear to the Fuselage 1. Insert one landing gear assembly into the pocket on the side of the fuselage as shown. The landing gear legs mount to the aluminum block which can pivot in the pocket. 2. Thread the included 3mm x 8mm machine screws through the landing gear leg into the threaded holes in the aluminum pivot block. 3. Repeat the process to install the second landing gear assembly. Mount the Spring Assemblies to the Fuselage 1.
EN Model Assembly Continued Lightweight and Heavy Stabilizer Joiners The Timber X includes two stabilizer joiners; a lightweight composite joiner, and a heavier steel joiner. For tame flying and maximum stability in general flight use the lightweight joiner to keep the CG at the front of the recommended CG range. For maximum performance and stability in high alpha maneuvers, use the steel joiner to shift the CG to the rear of the recommended CG range. Horizontal Tail Installation 1.
EN Model Assembly Continued Slat Installation (Optional) Required Adhesives A Medium CA 1. Carefully remove all the foam slat pocket covers (A) from the wing. 2. When the pocket is exposed, carefully apply medium CA to each slat pocket. 3. Mount the slat onto the wing with the rounded edge facing forward. Ensure that the left and right slats are on the correct wing half. The slat and wing halves are labeled with “L” and “R” indicators. Wing Assembly 1.
EN Transmitter and Receiver Binding / Switching ON and OFF SAFE Select (BNF Basic) This product requires an approved Spektrum™ DSM2®/DSMX® compatible transmitter. Visit www.bindnfly.com for a complete list of approved transmitters. Switching ON SAFE Select Binding Sequence The aircraft has an optional SAFE Select feature, which can be switched ON or OFF easily by binding in a specific manner as described below.
EN Battery Installation and ESC Arming Battery Selection The E-flite® 2200mAh 14.4V 4S 30C Li-Po battery (EFLM22004s30) is recommended. The EFL22003S30 battery may also be used. For maximum performance with 3 cells, a 13X6.5 electric propeller may be utilized. Refer to the Optional Parts List for other recommended batteries. If using a battery other than those listed, the battery should be within the range of capacity, dimensions and weight of the E-flite Li-Po battery packs to fit in the fuselage.
EN SAFE® Select Switch Designation SAFE® Select technology can be easily assigned to any open switch (2 or 3 position) on your transmitter. With this feature, you have the flexibility to enable or disable the technology while in flight. IMPORTANT: Before assigning your desired switch, ensure that the travel for that channel is set at 100% in both directions and the aileron, elevator, rudder and throttle are all on high rate with the travel at 100%.
EN Center of Gravity (CG) NOTICE: Install the battery but do not arm the ESC while checking the CG. Personal injury may result. The CG location is measured from the leading edge of the wing at the root. This CG location has been determined with the recommended Li-Po battery (EFLB22003S30). A pocket in the tail provides a space for extra tail weight for pilots wanting to push the 3D capabilities to the limit. Extra tail weight is not included.
EN Flying Tips and Repairs Consult local laws and ordinances before choosing a flying location. Range Check your Radio System Before you fly, range check the radio system. Refer to your specific transmitter instruction manual for range test information. Oscillation Once the AS3X system is active (after advancing the throttle for the first time), you will normally see the control surfaces react to aircraft movement.
EN PNP Receiver Selection and Installation The Spektrum AR636 receiver is recommended for ths airplane. If you choose to install another receiver, ensure that it is at least a 5-channel full range (sport) receiver. Refer to your receiver manual for correct installation and operation instructions. AR636 Port Assignments Installation (AR636 shown) BND/PRG = BIND 1. Remove the canopy from the fuselage. 1 = Throttle 2. Mount the receiver parallel to the length of the fuselage as shown.
EN Troubleshooting Guide Problem Aircraft will not respond to throttle but responds to other controls Extra propeller noise or extra vibration Reduced flight time or aircraft underpowered Possible Cause Throttle not at idle and/or throttle trim too high Throttle servo travel is lower than 100% Throttle channel is reversed Motor disconnected from ESC Damaged propeller and spinner, collet or motor Propeller is out of balance Prop nut is too loose Flight battery charge is low Propeller installed backwards Fl
EN BNF advanced receiver setup (optional) With the basic transmitter setup, the ailerons and flaps will operate separately. For increased aileron authority, the AR636 receiver included in the BNF version may be configured so the flaps can operate as both flaps and ailerons. Servo Plug Order Change 1. Remove the Y-harness plugged into the Ch-6 port on the AR636. 2. Insert two servo extensions (EFLREX9L) into the receiver ports; one in Ch-5 and one in Ch-6. 3. The left flap plugs into the Ch-5 extension.
EN AMA National Model Aircraft Safety Code Effective January 1, 2014 A. GENERAL B. RADIO CONTROL A model aircraft is a non-human-carrying aircraft capable of sustained flight in the atmosphere. It may not exceed limitations of this code and is intended exclusively for sport, recreation, education and/or competition. All model flights must be conducted in accordance with this safety code and any additional rules specific to the flying site. 1.
EN Limited Warranty What this Warranty Covers Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the product purchased (the “Product”) will be free from defects in materials and workmanship at the date of purchase.
EN FCC Information FCC ID: BRWDASRX15 Supplier’s Declaration of Conformity Contains IC: 6157A-AMRX15 Timber X 1.2m BNF Basic with AS3X and SAFE Select FCC Information EFL3850 This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device complies with part 15 of the FCC Rules.
IT Recommended Receivers•Empfohlene Empfänger Récepteurs Recommandés•Ricevitori Raccomandati PNP Only • Nur PNP • PNP Uniquement • Solo PNP Part # | Nummer Numéro | Codice SPMAR610 SPMAR6600T SPMAR6270T SPMAR8010T SPMAR9030T SPMAR636 SPMAR7350 SPMAR9350 Description AR610 6-Channel Coated Air Receiver Telemetry Equipped Receivers Beschreibung Descrizione Ummantelter AR610-6-KanalFlugzeugempfänger Récepteur aérien avec revêtement 6 canaux AR610 Ricevente aereo AR610 6 canali con rivestimento
IT Replacement Parts • Ersatzteile • Pièces de rechange • Pezzi di ricambio Part # | Nummer Numéro | Codice Description Beschreibung Description EFL3851 EFL3852 Fuselage: Timber X Wing Set: Timber X Timber X: Rumpf Timber X: Tragflächen Timber X - Fuselage Timber X - Aile EFL3853 Horizontal Stab W/Tube: Timber X Timber X: Höhenleitwerk mit Verbinder EFL3854 Steel Stab Joiner: Timber X Stahlstabschreiner: Timber X EFL3855 Leading Edge Slat: Timber X Timber X: Vorflügel EFL3856 EFL5253 EFL5254
IT Optional Parts • Optionale Bauteile • Pièces optionnelles • Pezzi opzionali Part # | Nummer Description Numéro | Codice EFL5261 Float Set: Timber EFLA250 Park Flyer Tool Assortment, 5 pc Description Timber: Schwimmerset Park Flyer Werkzeugsortiment, 5 teilig Timber - Flotteurs Assortiment d'outils park flyer, 5pc EFLAEC302 EC3 Battery Connector, Female (2) EC3 Akkukabel, Buchse (2) Prise EC3 femelle (2pc) EFLAEC303 EC3 Device/Battery Connector, Male/ Female 11.1V 3S 30C 2200mAh Li-Po 14.
Timber ® X 1.2m © 2019 Horizon Hobby, LLC. E-Flite, Timber, AS3X, DSM, DSM2, Airware, Bind-N-Fly, BNF, the Bind-N-Fly logo, Plug-N-Play, SAFE, the SAFE logo, ModelMatch, Dyanmite, EC3, Passport, Prophet and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, LLC. The Spektrum trademark is used with permission of Bachmann Industries, Inc. Futaba is a registered trademark of Futaba Denshi Kogyo Kabushiki Kaisha Corporation of Japan.
