Instruction Manual Bedienungsanleitung Manuel d’utilisation Manuale di Istruzioni
EN NOTICE All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit www.horizonhobby.com and click on the support tab for this product.
EN Table of Contents Transmitter and Receiver Binding..........................4 Low Voltage Cutoff (LVC) .......................................4 ESC/Receiver Arming, Battery Installation and Center of Gravity ...................................................5 Control Direction Tests ..........................................6 Control Centering .................................................7 Control Horn Settings ............................................7 Dual Rates and Expos .....................
EN Transmitter and Receiver Binding For a list of compatible DSM2/DSMX transmitters, please visit www.bindnfly.com Binding Procedure CAUTION: When using a Futaba transmitter with a Spektrum DSM® module, you must reverse the throttle channel and rebind. Refer to your Spektrum module manual for binding and failsafe instructions. Refer to your Futaba transmitter manual for instructions on reversing the throttle channel. 1.
EN ESC/Receiver Arming, Battery Installation and Center of Gravity CAUTION: Always keep hands away from the propeller. When armed, the motor will turn the propeller in response to any throttle movement. 1 Arming the ESC/receiver also occurs after binding as previously described, but subsequent connection of a flight battery requires the following steps. AS3X The AS3X® system will not activate until the throttle stick or trim is increased for the first time.
EN Control Direction Tests Traditional Control Direction Test You should bind your aircraft and transmitter before doing these tests. Move the controls on the transmitter to make sure the aircraft control surfaces move correctly and in the proper direction. Make sure the tail linkages move freely and that paint or decals are not adhered to them. AS3X® Control Direction Test This test ensures that the AS3X® control system is functioning properly.
EN Control Centering Before your first flight make sure the aircraft’s control surfaces are centered. 1. Power on the transmitter and then the aircraft. 2. Set all transmitter trims and sub-trims to zero. 3. Check the control surfaces to make sure they are centered. 4. If centering is required, use a pair of pliers to carefully bend the metal linkage (see illustration). Make the U-shape narrower to make the connector shorter. Make the U-shape wider to make the linkage longer.
EN Flying Tips and Repairs We recommend flying your aircraft outside in calm conditions. Always avoid flying near houses, trees, wires and buildings. You should also be careful to avoid flying in areas where there are many people, such as busy parks, schoolyards or soccer fields. Consult local laws and ordinances before choosing a location to fly your aircraft.
EN Power Components Service Disassembly CAUTION: DO NOT handle the propeller while the flight battery is connected to the ESC. Personal injury could result. Propeller 1. Carefully remove the screw (A) and propeller (B) from the motor shaft. B A Motor 1. Remove the battery hatch by gripping the front of the hatch, then pulling it up and away from the fuselage. 2. Disconnect the motor wire connector from the ESC/receiver connector. 3. Remove the screw (C) and motor (D) from the motor mount. C D 4.
EN Troubleshooting Guide AS3X Problem Possible Cause Solution Control surfaces not at neutral position when transmitter controls are at neutral Control surfaces may not have been mechanically centered from factory Center control surfaces mechanically by adjusting the U-bends on control linkages Aircraft was not kept immobile for 5 seconds after battery was plugged in Keep the aircraft immobile for 5 seconds after plugging in the battery Model flies inconsistently from flight to flight Aircraft was no
EN Troubleshooting Guide (Continued) Problem LED on receiver flashes rapidly and aircraft will not respond to transmitter (after binding) Control surface does not move Possible Cause Solution Less than a 5-second wait between first powering on transmitter and connecting flight battery to aircraft Leaving transmitter on, disconnect and reconnect flight battery to aircraft Aircraft bound to different model memory (ModelMatch™ radios only) Select correct model memory on transmitter and disconnect and recon
EN Horizon reserves the right to inspect any and all Product(s) involved in a warranty claim. Service or replacement decisions are at the sole discretion of Horizon. Proof of purchase is required for all warranty claims. SERVICE OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY.
EN Warranty and Service Contact Information Country of Purchase United States of America Horizon Hobby Phone Number/Email Address Horizon Service Center (Repairs and Repair Requests) servicecenter.horizonhobby. com/RequestForm/ productsupport@horizonhobby.
EN Compliance Information for the European Union Instructions for disposal of WEEE by users in the European Union EFL UMX Waco BNF Basic (EFLU5350) EU Compliance Statement: Horizon Hobby, LLC hereby declares that this product is in compliance with the essential requirements and other relevant provisions of the RED Directive. A copy of the EU Declaration of Conformity is available online at: http://www.horizonhobby.com/ content/support-render-compliance.
Replacement Parts – Ersatzteile – – Pièces de rechange – Ricambi – Part # • Nummer Description Numéro • Codice Beschreibung EFLU5351 Fuselage: Waco Rumpf: UMX Waco UMX Waco - Fuselage Fusoliera: Waco EFLU5352 Wing Set Waco Flügelsatz: UMX Waco UMX Waco - Aile Set ali Waco EFLU5353 Tail Set: UMX Waco Leitwerksatz: UMX Waco UMX Waco - Empennage Gruppo coda: UMX Waco EFLU5354 Pushrod Set: UMX Waco Schubstangensatz: UMX UMX Waco - Tringlerie Waco Description Descrizione Aste di comando: UMX
– Optional Parts and Accessories – – Optionale Bauteile und Zubehörteile – – Pièces optionnelles et accessoires – – Parti opzionali e accessori – Part # • Nummer Description Numéro • Codice Beschreibung Description Descrizione PKZ1039 Hook and Loop Set (5): Ultra Micros Klettband (5): Ultra Micros Bande autoagrippante (5) Set fascette fissaggio (5): Ultra Micros SPMA3060 USB-Interface: UM AS3X Programmer UM AS3X Programmiergerät Interface USB pour module AS6410NBL Interfaccia USB di programmazio
© 2017 Horizon Hobby, LLC. E-flite, AS3X, UMX, DSM, DSM2, DSMX, ModelMatch, Bind-N-Fly, BNF, Celectra and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, LLC. The Spektrum trademark is used with permission of Bachmann Industries, Inc. Futaba is a registered trademark of Futaba Denshi Kogyo Kabushiki Kaisha Corporation of Japan. All other trademarks, service marks and logos are property of their respective owners. US 7,898,130. US D578,146. PRC ZL 200720069025.
