™ ™ UMX Whipit Instruction Manual Bedienungsanleitung Manuel d’utilisation Manuale di Istruzioni
EN NOTICE All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby LLC. For up-to-date product literature, visit www.horizonhobby.com and click on the support tab for this product.
EN Table of Contents Transmitter Setup ..................................................4 Wing Installation ....................................................4 Transmitter and Receiver Binding...........................5 Flight Battery Installation and Receiver Arming ......6 Center of Gravity (CG) Adjustment ..........................7 Control Direction Test .............................................7 Control Centering ..................................................8 Control Horn Settings .......
EN Transmitter Setup Dual Rates To obtain the best flight performance, we recommend using a DSM2/DSMX radio capable of adjustable Dual Rates. The suggested settings shown here are the recommended starting settings. Adjust according to the individual preferences after the initial flight. NOTICE: Do not set your transmitter travel adjust over 100%. If the TRAVEL ADJUST is set over 100%, it will not result in more control movement, it will overdrive the servo and cause damage.
EN Transmitter and Receiver Binding Binding is the process of programming the receiver to recognize the GUID (Globally Unique Identifier) code of a single specific transmitter. You need to ‘bind’ your chosen Spektrum™ DSM2/DSMX technology equipped aircraft transmitter to the receiver for proper operation. Any full range Spektrum DSM2/DSMX transmitter can bind to the DSM2/DSMX receiver. Please visit www. bindnfly.com for a complete list of compatible transmitters.
EN Flight Battery Installation and Receiver Arming Arming the receiver also occurs after binding as previously described, but subsequent connection of a flight battery requires the following steps. It is normal for linear servos to make noise. Noise is not an indication of a faulty servo. 1 Power ON the transmitter, then wait 5 seconds. CAUTION: Always disconnect the Li-Po battery from the aircraft receiver when not flying to avoid over-discharging the battery.
EN Center of Gravity (CG) Adjustment The CG location is 36mm back from the leading edge at the wing root. This CG location has been determined with the recommended 1S 150mAh 3.7 Li-Po battery installed in the battery cavity located on the bottom of the aircraft. Balance the model on edge of a metal ruler to find the Center of Gravity. Place the ruler on the underside of the airframe at the CG location shown in the image to the right.
EN Control Centering Before the first flights, or in the event of an crash, make sure the flight control surfaces are centered when the transmitter controls and trims are neutral. The transmitter sub-trim must be set to zero. Adjust the linkages mechanically if the control surfaces are not centered. Use of the transmitter sub-trims may not correctly center the aircraft control surfaces due to the mechanical limits of linear servos. Make the U-shape narrower to make the connector shorter.
EN Flying Tips and Repairs Consult local laws and ordinances before choosing a location to fly your aircraft. We recommend flying your aircraft outside in calm conditions. Always avoid flying near houses, trees, wires and buildings. You should also be careful to avoid flying in areas where there are many people, such as busy parks, schoolyards or soccer fields. For additional tips on flying, refer to the product page at horizonhobby.com. causing one side of the airplane to rise, rather than the entire airplane.
EN Post Flight Checklist 9 9 1. Disconnect the flight battery from the receiver (Required for safety and battery life). 2. Power OFF the transmitter. 3. Remove the flight battery from the aircraft. 4. Recharge the flight battery. 5. Store the flight battery apart from the aircraft and monitor the battery charge. 6. Make note of the flight conditions and flight plan results, planning for future flights.
EN Limited Warranty What this Warranty Covers Horizon Hobby, LLC. (“Horizon”) warrants to the original purchaser that the product purchased (the “Product”) will be free from defects in materials and workmanship at the date of purchase.
EN include this request with your item submitted for service. Non-warranty service estimates will be billed a minimum of ½ hour of labor. In addition you will be billed for return freight. Horizon accepts money orders and cashier’s checks, as well as Visa, MasterCard, American Express, and Discover cards. By submitting any item to Horizon for service, you are agreeing to Horizon’s Terms and Conditions found on our website http://www.horizonhobby. com/content/_service-center_render-service-center.
EN Compliance Information for the European Union Declaration of Conformity (in accordance with ISO/IEC 17050-1) No. HH2014122205 Product(s): E-flite UMX Whipit DLG BNF Basic Item Number(s): EFLU3150 Equipment class: 1 The object of declaration described above is in conformity with the requirements of the specifications listed below, following the provisions of the European R&TTE Directive 1999/5/EC: EN 301 489-1 V1.9.2: 2012 EN 301 489-17 V2.1.1: 2009 Signed for and on behalf of: Horizon Hobby, LLC.
Replacement Parts – Ersatzteile – Pièces de rechange – Pezzi di ricambio Part # • Nummer Numéro • Codice Description EFLU3106 EFLU3102 EFLU3103 EFLU3104 EFLU3101 EFLU3105 PKZ3352 Beschreibung Description Decal sheet: UMX Whipit UMX Whipit: Dekorbogen Planche de décoration: UMX Whipit Wing: UMX Whipit UMX Whipit: Tragfläche Aile: UMX Whipit Tail Set: UMX Whipit UMX Whipit: Leitwerk Empennage: UMX Whipit Nose Cone: UMX Whipit UMX Whipit: Nasenkonus Cône de nez: UMX Whipit Fusleage: UMX Whipit UMX Whipit: Ru
™ ™ UMX Whipit © 2015 Horizon Hobby, LLC. E-flite, Whipit, Celectra, UMX, DSM, DSM2, DSMX, ModelMatch, Bind-N-Fly, the BNF logo and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, LLC. The Spektrum trademark is used with permission of Bachmann Industries, Inc. Futaba is a registered trademark of Futaba Denshi Kogyo Kabushiki Kaisha Corporation of Japan. All other trademarks, service marks and logos are property of their respective owners. US 7,898,130. US D578,146.