EFL1850 X-VERT Manual

ManualsBrandsE-flite ManualsAirplanesX-Vert VTOL BNF Electric Airplane / Multirotor Drone (504mm)

Operating the FPV Mount

The FPV camera mount does not require any programming or additional channels

in the transmitter. All functions are controlled by the ﬂ ight control board on the

aircraft. Changing between the ﬂ ight modes with the ﬂ ight mode switch moves

the camera to one of two preset positions.

• While in multirotor mode the camera faces toward the bottom of the aircraft.

This allows for a forward view while ﬂ ying in multirotor mode.

• While in either of the forward ﬂ ight modes, stability or acro, the camera faces

toward the front of the aircraft.

The angle of the camera can be adjusted slightly for your preferred optimal viewing

angle by adjusting the length of the control rod on the camera mount. Refer to the

Control Centering section for a description of how to adjust the length of the control

rod. Ensure any adjustments made to the camera control rod do not cause binding

in either the multirotor or forward ﬂ ight mode camera positions.

NOTICE: Never try to move the mount up or down by hand. Damage to the

mount servo may result.

Operating the Video Transmitter

Consult local laws and ordinances before operating FPV equipment.

In some areas, FPV operation may be limited or prohibited. You are

responsible for operating this product in a legal and responsible manner.

See the Available Frequency table to ﬁ nd the desired video channel and band. The

video transmitter channel and band are changed using the button on the video

transmitter, as shown. There are 6 LEDs on the video transmitter board. The red

LED is the channel indicator. The next 5 blue LEDs are the band indicators.

Channel Selection:

1. Channel 1 is indicated by the red LED glowing solid.

2. Press the button to cycle through the channels (1-8). The red LED will ﬂ ash

once as you cycle through each channel. Press the button once for each

channel until the desired channel is reached. If unsure of the current

transmitter channel, press the button to cycle the channels until you reach

channel 1, indicated by a solid red LED, then cycle to the channel desired.

Band Selection:

1. Press and hold the button to change the video transmitter band.

2. Each time the button is pressed and held, the blue band LED will indicate a

change to the next available band. The blue LEDs indicate FS/IRC band, band E

(North America only), band A, race band and band B, as shown in the illustration.

NOTICE: Due to the additional current draw of the camera, servo and video

transmitter on the aircraft electrical system, using the optional FPV system will

shorten the expected ﬂ ight times.

Band

CH 1 CH 2 CH 3 CH 4 CH 5 CH 6 CH 7 CH 8

Band A 5865 5845 5825 5805 5785 5765 5745 5725

Band B 5733 5752 5771 5790 5809 5828 5847 5866

Band E 5705 5685 5665 5665 5885 5905 5905 5905

FS/IRC 5740 5760 5780 5800 5820 5840 5860 5880

RaceBand 5658 5695 5732 5769 5806 5843 5880 5917

Band CH 1 CH 2 CH 3 CH 4 CH 5 CH 6 CH 7 CH 8

Band A 5865 5845 5825 5805 5785 5765 5745 5745

Band B 5733 5752 5771 5790 5809 5828 5847 5866

FS/IRC 5740 5760 5780 5800 5820 5840 5860 5860

RaceBand 5732 5732 5732 5769 5806 5843 5843 5843

Video Transmitter LEDs

150mW

North American

version

25mW

version

Band

Channel

Available Frequencies, North America (mHz)

Available Frequencies, European Union (mHz)

Channel button

LEDs