Installation Instructions

ManualsBrandsE. L. Mustee ManualsBathMustee CareGiver 30" Deep x 60" Wide Single Threshold Shower Floor, Left Hand, in White

Table Of Contents

4. Place Shower Floor directly on sub-floor or slab, level in both directions (Place level along top edge of tile

flange) do not use floor area which is tapered for water drainage.

HINT: You may want to install Shower Floor in a bed of gypsum cement or panel/floor adhesive for additional

support.

5. Seal "sanitary waste" by installing Drain Seal around pipe, tamp in place to bottom of drain body using a

1/4" (inch) diameter rod. Make sure top of drain seal is even with top of 2" (inch) waste pipe as shown in

sectional view and in full compliance with local code regulations pertaining to below floor waste connections.

6. You have been furnished with six (6) mounting clips to secure the Shower Floor, do not drill holes in Shower

Floor. Position two (2) clips per side and back, resting clip on top edge of tiling flange and securely fastening to

stud or bracing with screws provided. See Fig. 1.

CARE AND CLEANING

Quality Plumbing Products

E.L. MUSTEE & SONS, INC.

5431 West 164th Street • Brook Park, Ohio 44142 SI-171 (5•19)

MODEL: 360R ..............Right Hand Drain - White

360RBN ..........Right Hand Drain - Bone

DRAIN IS NOT FURNISHED

360L ..............Left Hand Drain - White

360LBN ..........Left Hand Drain - Bone

SI-171 (5•19)

The surface of your Molded Fiberglass Shower Floor may be cleaned with a mild soap solution in warm water using a soft

cloth. For stubborn stains use “Soft-Scrub” by Clorox or Lysol “Tub & Tile Cleaner” or a powdered detergent such as

“Spic-n-Span”. Do not allow cleaners to sit or soak on the surface. Wipe surface clean and rinse completely with water

immediately after cleaner application. Rinse and dry any overspray on nearby surfaces.

Never use abrasive scouring powder or steel wool pads, as they will scratch the surface.

AVAILABLE DRAIN ASSEMBLIES

PN 60.300A.........1 1/2" or 2" DRAIN ADAPTOR KIT COMPLETE - WHITE

PN 60.300A-BN...1 1/2" or 2" DRAIN ADAPTOR KIT COMPLETE - BONE

PN 82.400A....1 1/2" PVC - 90 DEG. WASTE CUP - PVC (SCH. 40) PIPE - SOLVENT WELD

PN 42.400A....2" PVC - 90 DEG. WASTE CUP - PVC (SCH. 40) PIPE - SOLVENT WELD

OPTIONAL ACCESSORIES

PN 360.100........ENTRY RAMP (WHITE)

PN 360.100BN...ENTRY RAMP (BONE)

PN 360.210...COLLAPSIBLE WATER BARRIER KIT

Summary of content (4 pages)

PAGE 1
4. Place Shower Floor directly on sub-floor or slab, level in both directions (Place level along top edge of tile flange) do not use floor area which is tapered for water drainage. HINT: You may want to install Shower Floor in a bed of gypsum cement or panel/floor adhesive for additional support. 5. Seal "sanitary waste" by installing Drain Seal around pipe, tamp in place to bottom of drain body using a 1/4" (inch) diameter rod.
PAGE 2
ROUGH-IN FRAMING-NEW CONSTRUCTION SHOWER FLOOR INSTALLATION NOTE: THIS DRAWING REFERS TO INSTALLING MUSTEE/PN 42.317A DRAIN ASSEMBLY DRAIN ASSEMBLY IS NOT FURNISHED - SEE "AVAILABLE DRAIN ASSEMBLYS" BACK COVER FIG. 1. 1. The Shower Floor must not be installed on exposed floor joists, if there is no sub-floor at the desired location, a one-piece section of sheating (CDX) the same thickness as the surrounding subfloor must be securely fastened in position, so that the Shower Floor is fully supported.
PAGE 3
ROUGH-IN FRAMING-NEW CONSTRUCTION SHOWER FLOOR INSTALLATION NOTE: THIS DRAWING REFERS TO INSTALLING MUSTEE/PN 42.317A DRAIN ASSEMBLY DRAIN ASSEMBLY IS NOT FURNISHED - SEE "AVAILABLE DRAIN ASSEMBLYS" BACK COVER FIG. 1. 1. The Shower Floor must not be installed on exposed floor joists, if there is no sub-floor at the desired location, a one-piece section of sheating (CDX) the same thickness as the surrounding subfloor must be securely fastened in position, so that the Shower Floor is fully supported.
PAGE 4
. Place Shower Floor directly on sub-floor or slab, level in both directions (Place level along top edge of tile flange) do not use floor area which is tapered for water drainage. HINT: You may want to install Shower Floor in a bed of gypsum cement or panel/floor adhesive for additional support. 5. Seal "sanitary waste" by installing Drain Seal around pipe, tamp in place to bottom of drain body using a 1/4" (inch) diameter rod.