Installation Instructions

ManualsBrandsE. L. Mustee ManualsBathMustee Durawall 36" x 36" White Corner Shower Wall Surround

Sl-154 (06•06)

MUSTEE

FIBERGLASS

SHOWERWALL

Before you assemble and install your MODEL 736C three-piece Molded Fiberglass Shower Wall unit you will have

to prepare the rough-in area, determine which side wall will have the shower head & control valve and if unit will be

equipped with a shower door or curtain. Please read instructions before proceeding with installation. The shower

wall unit does not require any trimming or cutting for normal installations.

FITS MUSTEE:

3636C - 36” X 36” NEO-ANGLE

3636DT - 36” X 36” DOUBLE THRESHOLD

SHOWER RECEPTORS

SEE BACK PAGE FOR SHOWER DOOR (ENCLOSURE) LISTING

IMPORTANT:

Quality Plumbing Products

E.L. MUSTEE & SONS, INC.

5431 West 164th Street • Brook Park, Ohio 44142

INSTALLATION INSTRUCTIONS

3636C - NEO ANGLE

SHOWER RECEPTOR

INSTALLATION INSTRUCTIONS

3636DT - DOUBLE THRESHOLD

SHOWER RECEPTOR

DIRECT MOUNTING TO STUDWALLS

Summary of content (6 pages)

PAGE 1
MUSTEE FIBERGLASS SHOWERWALL INSTALLATION INSTRUCTIONS DIRECT MOUNTING TO STUDWALLS INSTALLATION INSTRUCTIONS 3636C - NEO ANGLE SHOWER RECEPTOR 3636DT - DOUBLE THRESHOLD SHOWER RECEPTOR FITS MUSTEE: 3636C - 36” X 36” NEO-ANGLE 3636DT - 36” X 36” DOUBLE THRESHOLD SHOWER RECEPTORS IMPORTANT: SEE BACK PAGE FOR SHOWER DOOR (ENCLOSURE) LISTING Before you assemble and install your MODEL 736C three-piece Molded Fiberglass Shower Wall unit you will have to prepare the rough-in area, determine which side wa
PAGE 2
TOOLS AND MATERIALS* See back cover page. ROUGH-IN FRAMING After you have determined where your MUSTEE SHOWERWALL is to be located, you will have to construct the appropriate alcove. Be sure to plan your rough plumbing requirements (drain-venting-supply lines) at this time. Refer to “ROUGH-IN” illustrations for dimensions, Fig. A, B & E.
PAGE 3
. Place shower receptor directly on sub-floor or slab, level receptor in both directions — place level along top edge of tile flanges — do not use floor area which is tapered for water drainage. HINT: 4. You may want to install shower receptor in a bed of gypsum cement or panel/floor adhesive for additional support. Seal waste by installing drain seal around 2” (inch) waste pipe.
PAGE 4
A. One of the Side Panels will require drilling for the mixing/control valve handle(s). The showerhead may be located through the Side Panel or above it (which ever you chose in your rough plumbing). Double check all measurements before you do any drilling. The drilling should be completed before the unit is installed. Drill from the finished (inside) surface. B.
PAGE 5
SHOWERWALL INSTALLATION Trial fit the Corner Panel and both right and left Side Panels in place before applying any adhesive or mounting screws. Be sure to check alignment of the front edges of the Side Panels with the front surface of the shower receptor threshold as shown in drawings Fig. H or Fig. J. If any gap is present between the backside of the mounting flange and the face of the stud, a tapered piece of wood (shingle) should be inserted to take up the space.
PAGE 6
MUSTEE FIBERGLASS SHOWERWALL ACCESSORIES (OPTIONAL) 36” NEO ANGLE ENCLOSURE (use with: 3636C SHOWER RECEPTOR) PN - 36.750 ---- SILVER FINISH, OBSCURE GLASS PN - 36.770 ---- GOLD FINISH, OBSCURE GLASS PN - 36.760 ---- SILVER FINISH, HORIZONTAL STRIPE/GLASS PN - 36.780 ---- GOLD FINISH, HORIZONTAL STRIPE/GLASS 36” CORNER ENTRY ENCLOSURE (use with: 3636DT SHOWER RECEPTOR) PN - 36.200 ---- SILVER FINISH, HORIZONTAL STRIPE/GLASS PN - 36.201 ---- GOLD FINISH, HORIZONTAL STRIPE/GLASS TRIM KIT PN - 700.