Installation Instructions

ManualsBrandsE. L. Mustee ManualsBathMustee, Durastall 32" Deep x 32" Wide x 76" Tall Standard Shower Stall

SHOWER STALL

ASSEMBLY • INSTALLATION • REPAIR PARTS

FOR ONE OF THE FOLLOWING MODELS:

MODEL: 80 (32”) 140 (36”)

Cabinet (rigid corners) with Standard Base

complete with Curtain and Valve assembly.

MODEL: 82 (32”) 142 (36”)

Cabinet (rigid corners) with Extended Base

complete with Curtain and Valve assembly.

ROUGH-IN:

DURASTALL

SI-188 (8•07)

NOM. MODEL DIMENSION

SIZE NO.

AB CD

32” 80 & 82 32-5/8” 32-5/8” 16-5/16” 16-5/16”

36” 140 & 142 36-5/8” 36-5/8” 18-5/16” 18-5/16”

MODELS

80 & 140

MODELS

80 & 140

MODELS

82 & 142

MODELS

82 & 142

Summary of content (6 pages)

PAGE 1
® DURASTALL SHOWER STALL ASSEMBLY • INSTALLATION • REPAIR PARTS FOR ONE OF THE FOLLOWING MODELS: MODEL: 80 (32”) 140 (36”) Cabinet (rigid corners) with Standard Base complete with Curtain and Valve assembly. MODEL: 82 (32”) 142 (36”) Cabinet (rigid corners) with Extended Base complete with Curtain and Valve assembly. ROUGH-IN: NOM. SIZE MODEL NO.
PAGE 2
1. Suspend Center Panel off floor. Angle Corner Lock Strip slightly, and engage a short section of Center Panel into Lock Strip channel making sure smooth (gloss) side of panel will be on inside of shower stall. Align top edge of Corner Lock Strip with top edge of Center Panel. After total length of Lock Strip has been started, secure the strip by tapping from top to bottom with a mallet or hammer handle. Repeat procedure for remaining Lock Strip. (FIG. 1) FIG. 1 2.
PAGE 3
NOTICE: Standard Base is for use with Mustee free-standing cabinets only! NOT for “built-in” alcoves! STANDARD BASE A. Check shower base carefully making sure it is not damaged. Refer to the “rough-in” drawing and determine location of shower base. B. Assemble drain to shower base (see illustration) using all washers provided. Do not use any putty or thread sealant on either drain body or locknut. Hand tighten locknut, then wrench an additional 3/4 turn – maximum. C.
PAGE 4
NOTICE: Extended Base is for use with Mustee free-standing cabinets only! NOT for “built-in” alcoves! EXTENDED BASE A. Check shower base carefully making sure it is not damaged. Refer to the “rough-in” drawing and determine location of shower base. B. Assemble drain to shower base (see illustration) using all washers provided. Do not use any putty or thread sealant on either drain body or waste fitting.
PAGE 5
. Apply a small bead of quality waterproof caulking (not furnished) in track on Base – see illustration. Use the Safety Rail to lift the panel unit and place into the track against the caulking. It may be necessary to re-tap the Corner Lock Strips to ease installation. (FIG. 5) 6. From the outside, insert a 1/4”-20 x 1/2” Truss Head Screw in the Base and through the pre-punched hole in the Front Support. Secure with a 1/4”x 20 Hex Nut on the inside. Repeat for the remaining Front Support.
PAGE 6
PARTS ILLUSTRATION * Hardware NOT used (x 2) PARTS LIST KEY NO. PART NUMBER 32” 36” 1 2 3 4 5 6 7 8 9 80.318 80.318 80.316 80.220 70.108 70.204 80.310 80.803 40.803 40.317 40.317 40.315 80.220 40.105 40.207 40.310 80.803 40.803 10 40.806 40.806 DESCRIPTION Panel-Right Hand Panel-Left Hand Center Panel Corner Lock Strip (2 req’d) Top Frame - Molded Curtain Rod Safety Rail #10-”U” Nut (2 req’d.) 1/4”-20 x 1” Flat Head Screw (6 req’d.) Safety Rail Washer (6 req’d.) KEY NO.