Head up Display User Manual EL-311 EL-311R EL-101 Thank you for purchasing the Head Up Display! The User Manual will teach you how to operate the product. Please read the User Manual before starting using the product to make sure you operate the HUD correctly. After reading the User Manual, please save it in case if you need any information later.
Safety Warning The product operates safely as a design and manufacture were given priority in development. To avoid any potential risks, please follow the instructions when you are going to install, operating and cleaning the product. ● Before using the product, please read and understand all instructions, and save all instructions as they may be useful in the future. ● You are required to follow all warning instructions for the product.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC RF Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance.
I.
EL-311R DVR connector (Option) 12V Power input Reflective cover Screen on/off Brightness sensor Reset button -6-
EL-101 Reflective cover Screen on/off & brightness sensor Full-color and high brightness Micro SD card port Microphon Note： ：Long press the power button with 5 seconds for RESET device 5V Power input (USB Knob) DVR Video input Rear camera video -7-
II. Product features ● 4” TFT high-resolution image with full-color display layouts indicate rich information. ● Bright screen does not hurt the eyes. ● Brightness sensor: automatic detection when light reaches the sensor.
III. Specification EL-311 Voltage Storage Temperature Working temperature Current consume DC 12V -40℃ ~ +85℃ -30℃ ~ +80℃ 1A After turning off car engine, the products current consume ≦0.13mA 311 Overall size(L*W*H) 122.2mm*111.4mm* 29.
EL-311R Voltage Storage Temperature Working temperature Current consume DC 12V -40℃ ~ +85℃ -30℃ ~ +80℃ 1A After turning off car engine, the products current consume ≦0.13mA 311R Overall size(L*W*H) Length146.3mm*Width116mm*Height17.
EL-101 Voltage Storage Temperature Working temperature 5V -40℃ ~ +75℃ -30℃ ~ +75℃ Current consume 2A 101 Overall size(L*W*H) Length122mm*Width187mm*Height22mm - 11 -
IV. Instructions for starting the product [Preface] Before using the product, please follow below steps in order to sure the regular connections.
Bluetooth Connect Setting (Android System) Step 1 Install E-Where on your phone and HUD Remote APP. When you are doing route planning, you can share all hot spot (scenery) to SmartHUD via E-Where. HUD Remote is like a controller to remote HUD. Step 2 Turn on the blue tooth function：Setting>Bluetooth>Open, choose device named “SmartHUD”, and entering password 0000 for pairing.
Step 3 Enable the blue tooth function：Setting>Bluetooth>Open，Choose console equipped 「Smart HUD」，Enter password 「0000」。 14
When building a connection, SmartHUD will ask for confirmation to make sure you want to give the telephone saving authorization.
Bluetooth Connect Setting (iOS System) Step 1 Install E-Where on your phone and HUD Remote APP. When you are doing route planning, you can share all hot spot (scenery) to SmartHUD via E-Where. HUD Remote is like a controller to remote HUD. Step 2 Turn on the blue tooth function：Setting>Bluetooth>Open, choose device named “SmartHUD”, and entering password 0000 for pairing.
Step 3 Turn on Cellular：Settings＞Cellular >Cellular Data Step 4 Select Bluetooth and USB only 17
Step 5 Turn on personal Hotspot：Settings＞Personal Hotspot＞Personal Hotspot Bluetooth connect successful screenshot on mobile Color change from gray to white 18
Bluetooth connect successful on SmartHUD You can check connecting status at down-left side in safety mode. The icon will indicate status from (no connected)→ (Bluetooth connected)→ 19 (PAN connected).
Product Operation─ ─HUD Remote APP After establishing PAN, you can enable HUD Remote operation. The gesture operation is the same as using a mouse mode. HUD Remote will indicate functional teaching window at first operation. Click on the HUD Remote right side can review the functional teaching again after completing installation.
Note: When HUD Remote is in digital video record mode or safe mode, use long press follow by a down gesture to go back the Main Menu, do not support go back gesture to go back to Main Menu.
Product Operation─ ─Knob Choose up-right corner at Main Menu for checking the operation gesture. Note: Long press 3 seconds can start up voice recognition function on mobile (iOS system will start up Siri). If Siri is started up from mobile under connecting with HUD condition, HUD screen will pop up incoming call page.
Music 1. SD Music Playing page shows as below pictures. This icon go back to folder， refresh folder’s list. Support external capacity up to 32GB maximum and available to read MP3 and WAV music files.
2. BT Music Support to read the music list from mobile and work function as below indicated.
3. Internet Radio Data source is MUZEE.
Safety Free run / No route planning Road name of two blocks ahead Road name of one block ahead Current speed limit (Red circle will flash while speeding) Driving directions Current driving speed Current Temperature Next hour’s temp. Next 2 hours’ temp. Current time(show after GPS positioned) PAN connected Current road name Note: The triangles in the up-right corner indicate how close to your destination or next direction change. The first triangle will indicate to you at 200m to the destination.
With route planning Name of road one block ahead The distance of one block ahead Driving Directions Current speed limit (Red circle will flash while speeding) Current time(show after GPS positioned) PAN connected Distance to Current speed limit destination Current road name GPS Positioning Status: Check icon located at the right side of the main screen if changed from (No GPS signal) to current time, that means your GPS is positioned successfully.
V. Navigation For more details info please refer to navigation user manual. You can share POI(Point Of Interest) on your mobile via E-Where as destination to SmartHUD.
Android System (Share scenic from Google Maps) Step 1: Download E-Where APP Step 3: Look for scenic area (enter address or location into the search bar or pick a specific scenic area with address) E-Where Step 2: Enter Google Map on your mobile 29
Step 5: Step 4: Sharing the Scenic Area 30 Sharing to SmartHUD
Step 6: Set as destination Step 7: Sent successfully System will indicate text as “Sent successfully” if your mobile is connected with HUD. System will indicate text as “No connected car device. E-Where will send to device by server.” If your mobile is not connected with HUD.
iOS System (Share scenic from Apple Maps) Step 3: Enter keyword in search bar using Step 1: Download E-Where APP an address, select one place you want to go. E-Where Step 2: Allow E-Where to use your current location, so you are able to continue.
Step 5: Click the scenic information on the pin to enter edit page, then set it as destination. Step 4: Available for previewing the selected POI in map. You can also use your finger to move the map to select POI.
Step 6: Sent successfully System will indicate text as “Sent successfully” if your mobile is connected with HUD. System will indicate text as “No connected car device. E-Where will send to device by server.” If your mobile is not connected with HUD.
VI. Applications Content: News: Support to read news with Text to speech technique. Weather: Indicate current temperature and next three hours’ temperature. E-Where: Available to edit scenic to prefer group, pre-saving POI and share POI…etc. EZ-Talk: In-time communication software, need to work with installed APP on mobile. Available to send text, voice message, current location, and pictures…etc. to your contacts. Calendar: Need to use with EZ-Account APP to connect your Google account.
Traffic Report: The active traffic report enables the user to pass along information to those upcoming drivers about issues or incidents on the road ahead.
News Default setting is real-time news. Click Pause / Play / to switch to different kind of news.
Weather Indicate the weather information of your current located GPS position. The area description is written with local default language. Besides local language and English, system will directly indicate as English once the setting is changed to others. : Indicate the weather information of current position, data will be updating automatically per 5 minutes under stable internet connecting environment.
E-Where To use this function, please download eLeadrive and E-Where APPs on your mobile in advance. eLeadrive: The main entrance of E-LEAD cloud service, you can access the related information more easily by this application.
Connect with SmartHUD: 1. Click eLeadrive on your mobile to enter logging screen. Enter your account and password. (For initial operation, please select sign up and follow the indicated steps to finish signing process) 2. Please enter your phone number or e-mail address and password to log in. (Refer to the left picture as below) 3. After logging, eLeadrive will indicate the message of car device added at the bottom.
E-Where: By E-Where, you can search/collect POIs and share it with friends. It provides a more effective way to locate and navigate on SmartHUD.
EZ-Talk To use this function, please download eLeadrive and EZ-Talk APPs on your mobile in advance. eLeadrive: The main entrance of E-LEAD cloud service, you can access the related information more easily by this application. Features: - Bridge between your mobile and E-LEAD products - Profile picture settings - Supports E-Where& EZ-talk login Connect with SmartHUD: 1. Click eLeadrive on your mobile to enter logging screen.
2. Enter your account and password. (For initial operation, please select sign up and follow the indicated steps to finish signing process) 3. Please enter your phone number or e-mail address and password to log in. (Refer to the left picture as below) 4. After logging, eLeadrive will indicate the message of car device added at the bottom.
EZ-Talk Messenger: EZ-Talk Messenger is a FREE intstant messaging app make you be able to chat with your friends anywhere, anytime. This app not only supports mobile phones but also specific E-LEAD head units. You can send voice messages and location in car, and receive overall messages on phone. What we want to provide is a seamless experience from insinde of vehicle to outside of vehicle.
Support function at SmartHUD device: - Sync chats from mobile - : create new chat - : Account information - : Scenic transmits record, select one scenic and set it as destination to navigation - : Picture transmits record - : Add new member at this chatting room/Check members/Share current position(linked with Google Maps for preview)/Leave chat - : Set as Auto talk, turn on Auto play and Auto send function at same time. Auto Play: auto play incoming message.
a hold at any page. Calendar Click EZ-Account APP on your mobile, and set your Google account to connect with SmartHUD. After setting, you would be able to see the edited schedule.
Traffic Report The active traffic report enables the user to pass along information to those upcoming drivers about issues or incidents on the road ahead. It also enables the user to report problems or issues with your current position. You can choose to report situation directly or report vocally by uploading additional voice message to our server. While entering recording page, system will directly start recording voice for maximum time limit as 20 seconds.
- 48 -
VII. Mobile Support to loading dial pad, phoneBook, call history and messages from mobile. Note: iOS system is not supported for blue tooth message function. Dial pad / Call history / Message / : Update contact list to phone book. ※ Blue tooth phone function: Based on driver’s safety is top priority, all incoming calls will be popped up as full-screen notification besides you are staying at navigation and safety mode. At these two modes, incoming call will inform you as notify bar from top of screen.
function. If the incoming phone number is not within contact list, it will be presented as unknown. Dial pad Click the number you want to call. After keying, click during entering process, please use delete , clear - 50 - for calling. If there is any mistake for cancel.
Call history Downloading from the calling history on mobile. Missed calls Outgoing calls Incoming calls Message : update new messages.
VIII. Setting Provide personal favorite setting for Speeding Alert / Car Speed / Brightness / FM Transmitter / Volume / Language / Bluetooth / Car speed unit.
Car speed Set the number to adjust the indicated value from 0. The setting range is -50~50.
Speeding Alert The speeding indicator will remind you by color change when you are driving above the speed. You can set the value from 0. The setting range is -50~50. Brightness The device is able to detect outside light to switch screen presentation automatically. As personal preference you can switch by yourself, switch range is -5 to 5. Add or subtract by 1, use + and -.
FM Transmitter The ability to use FM Transmitter to listen to FM channels, using the car stereo channels and switches to listen to HUD music signal. (FM range: 88.1-107.9 MHZ) Volume Change to your personal preference.
Language According your personal preference you can set the language. The console support English, Traditional Chinese and Simplified Chinese. Bluetooth Auto-answer: Default is on. HUD will directly answer the incoming call after it keeps ringing till 10 seconds. For turning off this function, please cancel the block. New BT Pairing: Default is off for auto-connecting function.
Car Speed Unit Change the unit to your personal preference.
Version checking Step 1：Please enter to primary links/setting /language's screen Step2：Please practice how to use actuated button turn left move, and select a target toward to up one space gesture. Step 3：Please practice using rotated button turn right move, then select a target to move down once space gesture.
unsuccessful when updating. Step2：Put Micro SD card inside the console's SD card slot, And at the same time turn off your car.。 Step3：Turn on car engine and the automatic system will begin to update, please be patient and wait for the update. The program will alert you when you are able to remove the SD card. The console will also automatically restart after the update is complete. Step4：The preparation time before the update starts may be 1 minute.
