Datasheet
General Specification
and Information
General Specifications for Precision Pin Sockets
Mechanical data
Average forces for available clip types:
Standard type
Low force type
Super low force type
High force type
„Jumbo“ contact
Other clips and forces available on request
Contact life
Vibration as per EN60352-4
Shock as per EN60352-4
Thermal shock as per IEC 60068-2-14
Solderability as per IEC 60068-2-58
Dry heat steady state as per IEC 60068-2-2
Cold stead state as per IEC 60068-2-1
Damp heat cyclic as per IEC 60068-2-30
Moisture sensitivity Level (JEDEC J-STD-020C)
1.80N insertion / 0.90N extraction
0.70N insertion / 0.25N extraction
0.40N insertion / 0.15N extraction
4.00N insertion / 2.50N extraction
1.40N insertion / 0.25N extraction
min. 100 cycles
sinusoidal, 10 to 500 Hz, 10g,
1 octave/min, 10 cycles for each axis
half sine, 50g, 11ms, 3 shocks in 3
axes
-55°C/+125°C, 5 cycles, 30 minutes
245°C to 255°C 5 sec; Sn97Ag3
solder alloy
260°C for 20 sec.
-55°C, 2h
55°C, 90-100%rH, 24h
2 for PBT & Nylon
Material (RoHS compliant)
Standard temperature plastic: PBT
UL 94 V-0
High-temp plastic: Nylon, PCT, SPS, PPS, LCP
UL 94 V-0
Epoxy FR4:
UL 94 V-0 & UL 94 V-1
PBT, Nylon, PCT, SPS, PPS, LCP & Epoxy FR4
Terminal: CuZn
Contact: BeCu
Belongs to page:
14, 15, 16, 23, 17,19, 20, 24
25, 26, 27, 29
5, 6, 7, 8, 9, 10, 11, 12, 13, 14
15, 16, 21, 22, 20, 25, 26, 27
28, 33, 34, 35, 36, 37, 38, 39
40, 41, 42, 43
32, 5, 6, 7, 18, 22, 24, 29
If necessary pls. contact E-tec
for Material specification.
PCB holes for 2.54mm pitch standard connectors
Coplanarity thru-hole
General tolerances
1 for all other materials
1.00mm diameter
0.30mm
+/- 0.10mm
Male pin dimensions for standard clip
( except „Jumbo Contact“ )
( DIN 41 870, IEC 191 for square IC-legs )
Operating temperature (standard)
Processing temperature
injection molded insulator (high temp)
injection molded insulator (PBT)
Epoxy FR4 (Standard)
Epoxy FR4 (hi temp)
Electrical data
Contact resistance at 1A
Current rating (except “Jumbo” contact)
“Jumbo” contact
Contact capacitance at 1MHz
Insulation resistance at 500V DC for std & hi-temp
Insulation resistance at 500V DC for FR4 Epoxy
Breakdown voltage at 60 Hz
Contact resistance after 1000 ins./ext. cycles
55C to 125C
+250°C +0/-5°C for 20~40 sec.
(reflow solder)
+250°C +0/-5°C for 10 sec.
(wave solder only)
+220°C min. for 10 sec.
+260°C min. for 60 sec.
4,3 m typ.
1A max.
3A max.
2pF max.
5 10
9
min.
>10
4
M
500 V AC min.
7 m
DIM
„A“
„B“
„C“
min.
0,42
.016“
0,36
.014“
0,20
.008“
max.
0,56
.022“
0,55
.023“
0,30
.014“
General information concerning the E-tec interconnect products
Plating:
Standard tin plating:
min. 2.50μm Sn (leadfree) over Ni
Standard gold plating:
flash, max. 0,10μm Au over Ni
Higher gold platings are offered on request
Specifications:
The data contained in this catalog is of general nature and refers to standard products.
For example a „Current rating“ at an ambient temperature of 25° C reflects the value per individual contact.
Should you require any further data or test reports, you can obtain this information from your nearest E-tec
sales office.
The E-tec connectors conform with signal integrity requirements at high data and frequency rates. However
we cannot offer a general information about the max. frequency or data transmission rate. For such a
statement, it would require more information about the chosen configuration and pin-out, the length of the
cable and/or any other specific requirements regarding the application itself and its related signal integrity.
E-tec SMT connectors, male or female, are offered with a coplanarity of max. 0,10mm. They are adapted to
all modern SMT soldering processes and they can be handled easily with all currently existing placing
techniques. Customers may choose between various packaging options, such as tray, tube and tape & reel.
GENERAL POLICY
All information contained in this catalog, including illustrations, specifications and dimensions are accurate to the best of our knowledge, and reflect the
status as at the date of publication. Due to technical progress, it is subject to change without notice. Application information is informational in nature and
shall not be construed to warrant suitability of products for any particular purpose as performance may vary depending on the conditions to which a product
is subjected. Unless otherwise confirmed at the time of order, all E-tec products are non cancellable and non returnable items (NCNR). E-tec products are
warranted for 30 days and the warranty is limited strictly to replacement of products. This warranty does not cover any claims for natural wear and tear, nor for
any compensations, such as loss of production, loss of use, loss of orders, loss of profit, nor any other direct or indirect damages.
49