Broadband Router Quick Setup Guide V1.
Table of Contents TABLE OF CONTENTS ................................................................................................................................ 2 WARRANTY ..................................................................................................................................................... 4 FCC CAUTION ................................................................................................................................................ 5 SAFE SEATING GESTURES: ..
Copyright Statement This user’s manual, includes the products and software may be reproduced, transcribed, transmitted and stored. That totally depends on the legal authorized copyright. Furthermore, it can be translated into any language in any form or by any means, except some documents or public software without the copy permission of our company. ACCORDING TO THE AMERICA COPYRIGHT RULES IN 1976, PEOPLE CANNOT PUBLISH ANY UNAUTHORIZED CREATION IN ANY FORM OR BY ANY MEANS.
Warranty One-Year Warranty is provided for consumer products. This warranty is subject to the conditions and limitations set forth herein. ("We") warrants and tests the Product to be free from defects in material and workmanship and to conform to published specifications. During the warranty period, should the Product fail under normal use in the recommended environment due to improper workmanship or materials, we will repair the Product or replace it with a comparable one.
FCC Caution The device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Safe Seating Gestures: You should follow the manufacturer’s instructions for adjusting the backrest to fit your body properly. λ An adjustable chair that provides firm, comfortable support is best. λ Adjust the height of the chair so your thighs are horizontal and your feet flat on the floor. λ The back of the chair should support your lower back (lumbar region).
Chapter 1 Broadband Router’s Quick Setup 1.1 Router Mode’s Quick Setup Instruction Please open a Microsoft Internet Explorer, and enter http://192.168.1.
Please click on “Router” and “Apply Change”, then you will see the main page of “Router Home”, which means you already enter the page of Router mode’s Quick Setup. 1.
1.2.1 Time Zone Setting The section provides to change the Time. However, change the router’s date and time does not affect the date and time on your PCs. Please select your time Zone Please click on “Next” button to connect to next step.
1.2.2 LAN Interface Setup If you are using Broadband Router with multiple PCs on your LAN, please set up this function for multiple users to connect it. The default LAN IP for Broadband Router is 192.168.1.1. Please click on “Next” button to connect to next step.
1.2.3 WAN Interface Setup Broadband Router supports 4 connection types to WAN, select one of the WAN connection modes required by your ISP in below “WAN Access Type” page, the WAN setting pages will differ depending on what kind of WAN Type you select.
1.2.3.1 WAN Interface Setup–Static IP Choose Static IP Address if all WAN IP information is provided to you by your ISP. Broadband Router will not accept the IP address if it is not in this format, and the blanks of “IP Address”, “Subnet Mask” and “Default Gateway” must be input. Input the data provided by ISP DNS also needs to be inputted,otherwise you can’t use the domain name. Please click on “Next” button to connect to next step.
1.2.3.2 WAN Interface Setup– DHCP Client Choose DHCP Client to obtain IP address information automatically from your ISP. Select this option if your ISP does not give you any IP numbers to use. Please click on “Next” button to connect to next step.
1.2.3.3 WAN Interface Setup– PPPoE If your ISP uses PPPoE connection, your ISP will provide you with a username and password. Input it by your ISP provided. Input it by your ISP provided. Please click on “Next” button to connect to next step.
1.2.3.4 WAN Interface Setup– PPTP Some DSL service providers supply a special DSL modem in Europe or Big Pond Cable in Australia. This kind of modem only supports the PPTP tunnel to access the Internet; Please enter the account’s information of Account and Password which provided by your ISP. IP Address, Server IP Address and Subnet Mask are all input as necessary. Please click on “Next” button to connect to next step.
1.2.4 Wireless Basic Settings The first step of setting up the “Wireless Basic Settings” is to give a name for SSID, herewith the default name of SSID is Broadband_Rouetr, it’s suggested to use. Select the suitable item for you to use. It’s suggested to use. Please click on “Next” button to connect to next step.
1.2.5 Wireless Security Setup The “Encryption” item of “Wireless Security Setup” is optional; which means you can choose it under your demand, herewith it’s divided into two categories of “WEP” and “WPA”, if you want to protect your transmitting data; you can select it depended on the level of your request. Please follow the instruction below to complete “Wireless Security Setup”. It’s an optional item. a.
It has low level (64-bit) and high level (128-bit). It has “10 characters” and “26 characters”; it will be listed under your selection is low level (64-bit) or high level (128-bit). No matter if your selection is either 10 or 26 hexadecimal digits (0~9, a~f, and A~F) in the pull-down menu bar of “Key Format”; it will be based on whether you select 64-bits or 128-bits in the “Key Length” pull-down menu.
Select it by your request Please select it under your demand Please input it as necessary After setting up, please click on “Finished” button to connect to next step.
1.2.6 Quick Setup Finish The Quick Setup has been completed successfully when you see this screen: The system will be rebooting automatically and goes to the Product’s Diagram Homepage after countdown completed.
Chapter 2 AP Mode’s Quick Setup 2.
2.
2.2.1 LAN Interface Setup If you are using the Broadband Router with multiple PCs on your LAN, please set up this function for multiple users to connect it. The default LAN IP address for Broadband Router is 20.64.64.64 The default data is suggested to use. Please click on “Next” button to connect to next step.
2.2.2 Wireless Basic Settings The first step of setting up the “Wireless Basic Settings” is to give a name for SSID, herewith the default name of SSID is Broadband_Router, it’s suggested to use. Select the suitable item for you to use. It’s suggested to use Please click on “Next” button to connect to next step.
2.2.3 Wireless Security Setup The “Encryption” item of “Wireless Security Setup” is optional; which means you can choose it under your demand, herewith it’s divided into two categories of “WEP” and “WPA”, if you want to protect your transmitting data; you can select it depended on the level of your request. Please follow the instruction below to complete “Wireless Security Setup”. It’s an optional item. a.
It has low level (64-bit) and high level (128-bit). It has “10 characters” and “26 characters”; it will be listed under your selection is low level (64-bit) or high level (128-bit). No matter if your selection is either 10 or 26 hexadecimal digits (0~9, a~f, and A~F) in the pull-down menu bar of “Key Format”; it will be based on whether you select 64-bits or 128-bits in the “Key Length” pull-down menu.
Please select it under your demand Select it by your request Please input it as necessary After setting up, please click on “Finished” button to connect to next step.
2.2.
Then please enter http://20.64.64.
Chapter 3 WiFi ISP Mode’s Quick Setup 3.
Then you will enter the page of “Wireless Site Survey”, This function provides you with scanning the wireless network; which means if any Access Point is found, you could choose to connect it manually when the client is enabled, and after you choose the desired Access Point; this name will be listed automatically in the “SSID” of “Wireless Basic Settings” page for you to check.
Then you will see the main page of “Setup Wizard”, which means you already enter the page of WiFI ISP mode’s Quick Setup:
3.
3.2.1 LAN Interface Setup If you are using the Broadband Router with multiple PCs on your LAN, please set up this function for multiple users to connect it. The default LAN IP for Broadband Router is 10.64.64.64 Please click on “Next” button to connect to next step.
3.2.2 Wireless Basic Settings This function is used to configure the wireless LAN clients which may connect to your Access Point; once you connect the desired Access Point successfully, this name will be listed automatically in the “SSID”. It’s up to the Access Point of wireless LAN clients that you connect. Please click on “Next” button to connect to next step.
3.2.3 Wireless Security Setup The “Encryption” item of “Wireless Security Setup” is optional; which means you can choose it under your demand, herewith it’s divided into two categories of “WEP” and “WPA”, if you want to protect your transmitting data; you can select it depended on the level of your request. Please follow the instruction below to complete “Wireless Security Setup”. It’s an optional item. a.
It has low level (64-bit) and high level (128-bit). It has “10 characters” and “26 characters”; it will be listed under your selection is low level (64-bit) or high level (128-bit). No matter if your selection is either 10 or 26 hexadecimal digits (0~9, a~f, and A~F) in the pull-down menu bar of “Key Format”; it will be based on whether you select 64-bits or 128-bits in the “Key Length” pull-down menu.
Please select it under your demand Select it by your request Please input it as necessary After setting up, please click on “Next” button to connect to next step.
3.2.4 Quick Setup Finish The Quick Setup has been completed successfully when you see this screen: Once if the countdown is at 0 seconds, please enter http://10.64.64.
The system will go to the main page of “Operation Mode”, and you will see the “WiFi ISP Home” appearing on left sub menu, which means the Quick Setup of WiFi ISP mode is successfully completed:
4. The 20cm safe distance from antenna to the user shall be maintained.